1. Introduction. 4 2. Safety 4 3. Controls and Jacks. 6 4. Symbols and Annihilators. 7 5. Operating Instructions. 8 5-1. DG Voltage Measurements 8 5-2. AC Voltage (Frequency, Duty Cycle) Measurements. 9 5-3. DG Current Measurements. 10 5-4. AC Current (Frequency, Duty Cro) Measurements. 1 5-5. Resistance eerie 12 §-6. Continuity . . 18 §-7. Diode Test... ” 5-8. Frequency/Duty Cycle Measurements actor) 5-9. Temperature 5-10. Autoranging/Manual Range Selection. 5-11. ccc.
Settee— 1. Introduction ‘This mater measures AC/DC Voltage, AC/DC Currant, Resistance, Frequency {electrical & electronica, Diode Test, and Continuity. 1t features a waterproof, rugged design for heavy duty use. Proper use and Cara of this meter will provide many years of blare service. 2. Safety A ‘This symbol adjacent to anther symbol, terminal or operating device Indicates that the operator must refer ta an explanation In the Operating Instructions to avoid personal Injury or damage to the meter.
elo PER [EC1010 OVER VOLTAGE INSTALLATION CATEGORY (OVER VOLTAGE CATEGORY | Equipment of OVER VOLTAGE CATEGORY | Is equipment fer connection to results In which measures are taken to Limit the transient overaggressive to an appropriate low level. Note — Examples Include protracted electronic cults. (OVER VOLTAGE CATEGORY Il Equipment of OVER VOLTAGE CATEGORY 1 Is energy-consuming equipment 10 be supplied from the fixed Installation. Note — Examples Include household, office, and laboratory appliances.
elo | | s ETT, 8 by one or more of tha following measures: Contrarian or relocate the receiving antenna Increasing the separation between the equipment and receiver. Conn act the equipment into an outs on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. The device must not ba co-located or operating in conjunction with any other amen or transmitter.
elo pT FTE 3. Controls and Jacks counts LCD display bunion 3-RANGE button 4-Soda bunion S-Function switch 6-ma, pA and 10A input jacks 7-COM input jack 8-Positive input jack 9-Hz and % button 10-HOLD and Fightback bunion 11-RELATIVE button Note: Tilt stand and battery compartment are on rear of unit. 4.
Metternich 5. Operating Instructions 'WARNING: Risk of electrocution. High-voltage circuits, both AC and DC, are ‘vary dangerous and should be measured with great care. 1. ALWAYS turn the function switch to the OFF position wham the meter Is nat In use. 2.1 "OL" appears In the display during a measurement, the values exceeds the range ‘you java selected. Change ta a higher range. 5-1.
5-2. AG Voltage (Frequency, Duty Cycle) Measurements WARNING: Risk of Electrocution. The probe tips may not be ion enough to contact the live parts Inside some 240V outlets for appliances because the contacts SARS recessed deep In the outlets. As a result, the reading may show 0 volts when the outlet actually has voltage on It. Make sure the prob tips are touching the metal contacts Inside the outset he fora assuming that no voltage Is preterit.
o oe 6-3. DC Currant Measurements CAUTION: Do not mae 20A current measurements for longer than 30 seconds. Exceeding 30 seconds may cause damage to the meter and/or the test leads. 1. Insart the black test lead banana pig Imo the negative COM Jack. 2 For current measurements up to 4000pA DC, set the function switch to the yellow ssh position and Insert the red test lead banana plug Ino the WA/MA jack. 3.
Tran RMS Transactor Dial Multi meter User Man gal 5-4. AC Current{Frequency, Duly Countermeasures CAUTION: Do not aka 20A current measurements for longer than 30 seconds. Exceeding 30 seconds may cause damage to the meter and/or the test leads. 1.
True AMS Estranging Digital Mutterer User Manga! w 5-5. Resistance Measurements 'WARNING: To avoid electric shock, disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements. Remove the batteries and unplug the line cords. 1 Sat the function switch to the gran £2 aq position. insert the black test lead banana plug into the negative COM jack. Insert the red test lead banana plug into the positive £2 jack.
elo a. err ® 5-6. Continuity Check WARNING: To avoid electric shock, never measure continuity on circuits or wires that have voltage on them. 1.Sat the function switch to the green £2 a § potion. insertions back ead banana plug Into the negative COM Jack. Insert the red test lead banana pig Into the positive £2 jack. 3.Press the MODE button to Indicate * and * “CY on tha display 4 Touch the test probe tps to the cultural or wire ‘you wish to check. 5.
elo a. EET ¢ 5-8. Frequency/Duty Cycle Measurements (Electronic) 1.Sat the rotary function switch to the green “Hz %" position. 2.Press the Hz/% button to Indicate “Hz” on the display. 8. Insart the black sad banana plug Int the negative COM Jack and the red test lead banana pig Into the positive Hz Jack. 4.Touch the test prob tips to the cultural under test. 5.Read the piquancy on the display. oh 6. Prass the Hz/% bunion again to Indicate on — the display. i 7. Rsad the % of duty cycle on tha display 5-9.
elo oe a. ere © 1.Press the RANGE key. The “AUTO” display indicator will tum off. 2 Press the RANGE key to step through the available ranges until you select the range you want. 3.To exit the Manual Ranging mode and return to Auto ranging, press and hold the RANGE key for 2 seconds. Note: Manual ranging does nat apply for the Frequency functions. 5-11.
elo ¢ a. ETT, ¢ ‘will appear on the display. 3. The display will now indicate the difference between the stored value and the measured value. 4 Press the REL button to ext the relative mode. Note: The Relate function does nat operate In the Frequency function. 5-14. Display Back light Press and hold the HOLD key for > 1 Second to tum on ar off the display back light function. The fightback will automatically tum off after 30 seconds. 5-15. HOLD The hold function freezes the reading in the display.
Dropping It can damage the Electron parts or the sacs. 4 KEEP THE METER CLEAN. Wipe the case occasionally with a damp cloth. DO NOT use chemicals, cleaning solvents, or detergents. 5.USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE. Remove old or weak batteries so they do not leak and damage the unit. 6.IF THE METER I$ TO BE STORED FOR A LONG PERIOD OF TIME. ‘The batteries should ba removed to prevent damage ta the unt. 6-1.
® & Function | Range Resolution | Accuracy Frequency | 0.
elo oe a. airs © Enclosure Double molded, waterproof $hock(Drop Test) 6.5 forefeet maters) Diode Test Test currant of 0.9mA maximum, open circuit voltage 2.8V DC typical Continuity Cheek Audible signal will sound If the resistance Is less than approx ), test current <0.
{162 x 82 x 58mm) (includes holster) Safety This meter Is Intended for origin of Installation use a nd protracted, against the users, by double Insulation per ENG1010-1 and IEC61010-1 2 Edition(2001) to Category IV 600V and Category Ill 1000V; Solution Degas 2. The meter also meats UL 81010-1, 2 Edition{2004), CANCAN C22 2 No.