- GPS TRACKER - For Vehicle User Manual MODEL:TK319 - Professional Tracking System - 1
CATLOG Ⅰ. Product Features ........................... 5 Ⅱ. Components and Accessories .... 7 Ⅲ. SIM card Installation.................... 9 Ⅳ. Device Installation ..................... 10 4.1 Install device ........................ 10 4.2 Device wiring definition ...... 12 4.3 Relay wiring......................... 14 Ⅴ. Power On / Off ............................ 15 5.1 Power on .............................. 15 5.2 LED Indicators..................... 15 5.3 Power off ............................. 16 Ⅵ.
7.2 Vibration Alarm ................... 18 7.3 Collision / falling Alarm ...... 18 7.4 Speed Alarm......................... 18 7.5 Shift Alarm........................... 18 7.6 Geo-fence Alarm .................. 18 7.7 Power disconnect Alarm ...... 19 7.8 Low battery Alarm ............... 19 Ⅷ. Device Setting .......................... 19 Ⅸ. Trouble shooting........................ 20 9.1 Cannot connect platform ...... 20 9.2 Offline status ........................ 20 9.3 No positioned .....................
Welcome to use our device,please read this manual carefully to install and operate device exactly. This user manual is for reference only. If some contents and operation steps are inconsistent with those for the actual product, the latter will prevail.
Ⅰ. Product Features ■ Supports GSM/WCDMA, include 9 band, universal in the world. ■ Super Wide Input Voltage:7-72V DC. ■ GPS precise positioning, Support A-GPS, uploaded by WCDMA/GPRS regularly, real-time tracking and history track playback. ■ ACC status detection ■ Support Temperature, SOS, External battery, GPIO(Hardware customization, Choose one of the four) ■ Serial port, also can be GPIO port(Firmware Customization). ■ Built-in battery, power disconnect alarm & low battery alarm.
Basic Specifications Voltage 12/ 24/ 36/ 48/ 60/ 72 VDC Work Current GPRS(140mA); HSPA(460mA) Standby Current IDLE(2mA@12V) GPS Accuracy 5-15m LBS Accuracy >100m GPS Band 1575MHz GSM Band 850/900/1800/1900MHz WCDMA Band W800/W850/W900/W1900/W2100MHz Hot/warm/cold Start <3s,<15s,<60s Temperature-Sensor Accuracy Temperature-Sensor Arrange ± 0.
Ⅱ.
■ Accessories Power Cable(Default) Relay(Optional) Temperature Sensor(Default Optional) SOS( Optional) External Battery(Optional) Relay for remotely cut engine, Temperature sensor used for monitoring temperature, SOS button used for help, External battery used for power supplier, (Temperature senor, SOS button, External battery can be only chose one of the three) Please note that device should be matched with accessories to realize these functions.
Ⅲ.
Press cover and close Note: ●Please cut off the power before installing or uninstalling SIM card. ●SIM card should have GPRS/WCDMA function, open it’s network through operator. ●SIM card should open Caller Identification function for telephone querying. ●If you enable the PIN code of the SIM card, please use your mobile phone to disable the PIN code. ●Please make sure SIM card has sufficient balance. Ⅳ. Device Installation 4.1 Install device 4.1.
Please make sure to install device with this side upward, and use wide strong double-sided adhesive sponge to fix it. 4.1.2 Installation Notice ●Hide device properly inside the car body in order to avoid damages. ●Keep device away from RF emission sources such as backing radar, car burglar alarm and other vehicle mounted communication devices. ●Suggest to use wide strong double-sided adhesive sponge to fix it, or use cable ties and other liable methods to fix it.
4.2 device wiring definition Total schematic wiring device 4.2.1 Power cables and interface The standard input voltage of device is 9V-72VDC, so please choose the our original power cables, the red cable is positive and the black cable is negative; Please ground negative pole separately or ground it to ground connection, not to any other ground.
ignition status of vehicle; the ACC cable can also be connected directly to the positive pole of the vehicle power, then the position server think that the vehicle is always ignited. Connect the 4# cable (yellow cable) to the 85 device(with small yellow cable) of the relay. Use cable ties to fix the relay to waterproof place, or use plastic bags to cover the relay.. Connect Temperature sensor with PIN7 & PIN8.
4.3 Relay wiring Relay wiring diagram shows how to wire the relay to control the fuel pump: 4.3.1 Connect the 86 port to the positive pole of the vehicle power (+12V/+24V), connect the 85 port to the 4# cable of device. 4.3.2 Cut off the positive pole of the fuel pump, next serial connect the positive pole to the 87a port of the relay, and connect another pole to 30 port, showing as in the figure.
Notice: Be sure the voltage of the vehicle power should match up to the working voltage of relay, or relay will be damaged. Ⅴ. Power On / Off 5.1 Power on Power on: insert a valid SIM card and wire all the cables, device will power on. 5.2 LED Indicators The red LED flickers fast when device is searching for GSM network, it flickers intermittently when device has registered the GSM network successfully.
1. Red LED(indicates GSM working state) Searching for GSM/WCDMA network GSM/WCDMA works normally Fast blinking Slow blinking 2. Blue LED(indicates GPS signal state) Searching GPS Satellites GPS works normally Fast blinking Slow blinking 5.3 Power off Disconnect the external power and take off SIM card, after a while device will shut down. Ⅵ. Inquiry/Monitoring/Cut Oil 6.1 Inquiry by service platform 6.1.
your dealer to get installation package. 6.2 Inquiry by SMS You can write a positioning SMS sending to device to inquiry position, device will reply position SMS or map link. The SMS commands please refer to the Operation Commands 6.3 Cut Engine/Restore 6.3.1 Cut off oil circuits Server(GPRS) or Manager number (SMS) can send cut-fuel-circuit commands to device when needed. Engine can not start and vehicle will be locked.
7.2 Vibration Alarm Conditions: When the Vehicle Vibration occurs. Note: You need to set vibration sensitivity and time, there is an alarm switch. 7.3 Collision / falling Alarm Conditions: When Vehicle Collision or falling occurs. 7.4 Speed Alarm/Cut engine when over speed Alarm Conditions: When vehicle speed over and below the setting speed.
Note: You need to set the conditions of crossing fence, fence types and so on. 7.7 Power disconnect Alarm Conditions: When the device is disconnected from external Power. 7.8 Low battery Alarm Conditions: When the device is disconnected from external Power and built-in battery power falls below a certain value . Note: Alarm parameters must be set before work in 7.1, 7.2, 7.4,7.5&7.
Ⅸ. Trouble shooting 9.1 Cannot connect platform device is never online on the position server when installed at the first time. Please check device: 1)If power cables are wired correctly? Pay attention to not connect them to controlling cables of vehicle. 2)If SIM card is installed correctly? Please refer to the installation instructions. 3)Check the status of LED indicators. If device is OK, red LED and blue LED will intermittently flick.
operator If network is OK. 4)Check if SIM card has enough balance. 5)If device becomes offline on the last day of one month, please check GPRS is closed or not. 6)Inquiry parameters of device via commands and check replied parameters. 9.3 No positioned If the GPS is active, but device cannot be positioned for long time, please check device: 1)If the vehicle is in the place where there is no GPS signal. 2)The upside of device should be installed with face toward the sky.
open places. 9.5 Commands receiving abnormally 1)Check the commands format. 2)Check if the vehicle is in the places where there is GSM signal. 3)Check if the SIM card is properly installed. Ⅹ. Warranty Rules 10.1 Special statement 1)Technology change without notice. 2) If the color and appearance are inconsistent with those for the actual product, the latter will prevail. 3)Warranty card is only valid for devices with the following IMEI.
10.3 After sales Any of the following circumstances not covered by the warranty, but may be appropriate to pay repair: 1)More than the warranty period. 2)Unauthorized removal or repair damaged. 3)Damage caused by improper installation, use, maintenance, custody. 4)IMEI label is torn or Obscure. 5)Warranty certificate and product models do not match or warranty certificate be altered. 6)Damage caused by force majeure.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Warranty Card NAME TEL Address Model IMEI Number Selling Unit Purchase Date YY MM 24 DD
25 Date Description Records Completion Date Maintenance Records Engineer
26