WCDMA 3G GPS Tracker For Vehicle S User Manual V2.
Ⅰ. Product Features.............................5 Ⅱ. Components and Accessories.....7 Ⅲ. SIM card Installation.....................8 Ⅳ. Terminal Installation...................11 4.1 Install the terminal................ 11 4.2 Terminal wiring definition.... 13 4.3 Relay wiring..........................15 Ⅴ. Power On / Off............................. 16 5.1 Power on............................... 16 5.2 LED Indicators......................16 5.3 Power off...............................18 Ⅵ.
7.5 Geo-fence Alarm...................20 7.6 Power disconnect Alarm....... 20 7.7 Low battery Alarm................ 20 Ⅷ. Terminal Setting........................ 21 Ⅸ. Trouble shooting.........................21 9.1 Cannot connect platform.......21 9.2 Offline status......................... 22 9.3 No positioned........................ 23 9.4 Position drift..........................24 9.5 Commands receiving abnormally.................................. 24 Ⅹ. Warranty rules..............................
Welcome to use our terminal,please read this manual carefully to install and operate the terminal exactly. This user manual is for reference only. If some contents and operation steps are inconsistent with those for the actual product, the latter will prevail. Using TK119 GPS tracker, we can position, monitor and control the vehicle on the position server via GPS,WCDMA,GPRS and Internet. It can help customers to manage transparently, reduce cost, maintain security and raise efficiency.
Ⅰ. Product Features ■ Supports WCDMA triple band ,GSM quad bands,universal in the world. ■ Input Voltage:7-36V DC. ■ Located by GPS / LBS, support A-GPS ■ GPS data uploaded by WCDMA/GPRS regularly, Web browser platform, Smart phone app and SMS query. ■ ACC and vehicle status detection. ■ Built-in battery, Power disconnect alarm & Low battery alarm. ■ Built-in G-sensor ,Vibration, collision and falling alarm. ■ GEO-fence alarm, speed & shift alarm. ■ Remotely cut oil by Relay.
Basic Specifications Voltage 12 / 24 / 36 VDC Work Current <50mA@12V Standby Current <10mA@12V GPS Accuracy 5-15m LBS Accuracy About 200m GPS Frequency 1575MHz GSM Frequency 850 / 900 / 1800 / 1900 MHz WCDMA Frequency W850 / W1900/ W2100 MHz Hot/warm/cold Start <3s,<15s,<60s Battery Capacity 70mAh Dimensions (mm) 87(L)X41.
Ⅱ. Components and Accessories ■ 2.
Power Cables(Fault) Relay(Optional) Relay for remotely cut off/resume oil,please note that the devices should be matched with accessories to realize these functions Ⅲ.
Insert SIM card to the device correctly waterproof silicone must be put 9
Tighten the screws after put the cover correctly Note: ●Please cut off the power before installing or uninstalling the SIM card. ●The SIM card should have network to internet. ●SIM card should open Caller Identification function for telephone querying. ●If you enable the PIN code of the SIM card, please use your mobile phone to disable the PIN code. ●Please make sure that the SIM card has sufficient balance.
Ⅳ. Terminal Installation 4.1 Install the terminal 4.1.1 Please install the terminal concealed by professional person Please make sure to install the terminal with this side upward, and use wide strong double-sided adhesive sponge to fix it. Please make sure to install the terminal with this side towards the ground, and use wide strong double-sided adhesive sponge to fix it. 4.1.2 Installation Notice ●Hide the terminal properly inside the car body in order to avoid damages.
without any metal material covered on the top.
4.2 Terminal wiring definition Total schematic wiring terminal 4.2.
is negative; Please ground the positive pole separately or ground it to ground connection, not to any other ground. Connect the ACC cable (orange cable) to ACC switch of the vehicle, then the position server can get the information about the vehicle power; the ACC cable can also be connected directly to the positive pole of the vehicle power, then the position server think that the vehicle is always ignited. Connect the 4# cable (yellow cable) to the 86 terminal(with small yellow cable) of the relay.
4.3 Relay wiring Relay wiring diagram shows how to wire the relay to control the fuel pump: 4.3.1 Connect the 85 terminal(with small white cable) to the positive pole of the vehicle power (+12V/+24V), connect the 86 terminal(with small yellow cable) to the 4# cable of the terminal. 4.3.
Bottom of the relay Wiring Diagram Notice: Be sure that the voltage of the vehicle power should match up to the working voltage of the relay, or the relay will be damaged. Ⅴ. Power On / Off 5.1 Power on Power on: insert a valid SIM card and wire all the cables, then the terminal power on itself. 5.
intermittently when the terminal has registered the WCDMA network successfully. The blue LED flickers fast when the terminal is searching for the GPS satellite signal, it flickers intermittently when the terminal when the terminal has searched the satellites and can be positioned. WCDMA/GSM LED GPS LED 1. Red LED(indicates WCDMA/GSM working state) Fast blinking Slow blinking Searching for WCDMA/GSM network WCDMA/GSM works normally 2.
5.3 Power off Disconnect the external power and take off SIM card, after a while the terminal will shut down. Ⅵ. Inquiry/Monitoring/Cut Oil 6.1 Inquiry by service platform 6.1.1 Web Browser platform Login the service platform and enter your ID and password to check the position of the terminal. Please ask your dealer for the WWW address of the position service platform. 6.2.2 Smart phone applications You can use a smart phone to check the terminal’s position.
6.3 Cut Oil /Restore 6.3.1 Cut off oil circuits The position server or the managers can send cut-off fuel commands when needed. The fuel of the vehicle will be cut off on the premise of safety, and the vehicle will not be powered on. To make sure the safety of the vehicle, the fuel of the vehicle will be cut off only if the terminal has positioned by GPS and the speed of the vehicle is less than 20KM/h or the vehicle is not moving. 6.3.
7.2 Collision / falling Alarm Conditions: When the Vehicle Collision or falling occurs. 7.3 Speed Alarm Conditions: When the vehicle over and below the set speed. Note: You need to set the low speed limit and high speed limit. 7.4 Shift Alarm Conditions: When the vehicle occur the set shift in the Flameout state. Note: Only valid in flameout state and vehicle occur the set shift distance. 7.5 Geo-fence Alarm Conditions: when the vehicle entry / exit / across the Geo-fence.
external Power and built-in battery power falls below a certain value . Note: When above alarm occurs, the terminal will send alarm to service platform, meanwhile send a SMS message to the administrator number if the number is set. Note: Alarm parameters must be set before work in 7.1, 7.3, 7.4 & 7.5 , Please refer to the Ⅷ. Terminal Setting Please refer to the Ⅸ. Trouble shooting 9.
cables of the vehicle. 2)If the SIM card is installed correctly? Please refer to the installation instructions. 3)Check the status of the LED indicators. If the terminal is OK, the red LED and the blue LED will intermittently flick. 4)Inquiry the parameters of terminal via commands and check the accuracy of the parameters. 9.
4)Check if the SIM card has enough balance. 5)If the terminal becomes offline on the last day of one month, please check network is closed or not. 6)Inquiry the parameters of terminal via commands and check the accuracy of the parameters. 9.3 No positioned If the GPS is active, but the terminal cannot be positioned for long time, please check the terminal: 1)If the vehicle is in the place where there is no GPS signal. 2)The upside of the terminal should be installed with face toward the sky.
9.4 Position drift Serious position drift will be found in places where GPS signal is poor. Please drive the vehicle to the open places. 9.5 Commands receiving abnormally 1)Check the commands format. 2)Check if the vehicle is in the places where there is WCDMA signal. 3)Check if the SIM card is properly installed. Ⅹ. Warranty rules 10.1 Special statement 1)Technology change without notice. 2) If the color and appearance are inconsistent with those for the actual product, the latter will prevail.
10.2 Warranty period Since the date of purchase, passive waste host has one year warranty. 10.3 After sales Any of the following circumstances not covered by the warranty, but may be appropriate to pay repair: 1)More than the warranty period. 2)Unauthorized removal or repair damaged. 3)Damage caused by improper installation, use, maintenance, custody. 4)The IMEI label is torn or Obscure. 5)Warranty certificate and product models do not match or warranty certificate be altered.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Warranty Card NAME TEL Address Model IMEI Number Selling Unit Purchase Date YY MM 26 DD
27 Date Description Records Completion Date Maintenance Records Engineer