Installation Instructions

USB充电接口
电源开关
多功能组合键
269.3x97.4x7.9mm
142.7x97.4x16mm
0.7mA
20
80
输入电压: 5V 输入电流: 50-100mA
1.5mA
电源指示 : 打开电源开关,蓝色指示灯点亮后熄灭.
通道指示 : 选择及切换通道,对应通道蓝色指示灯点亮后熄灭.
配对指示 : 按对码键,蓝色指示灯闪烁,配对成功后熄灭.
低压指示 : 红色指示灯闪烁表示进入低电压状态需充电.
充电指示 : 红色指示灯点亮,充满电后熄灭.
Capslock指示：绿色指示灯点亮.
电源指示 : 打开电源开关,蓝色指示灯点亮后熄灭.
通道指示 : 选择及切换通道,对应通道蓝色指示灯点亮后熄灭.
配对指示 : 按对码键,蓝色指示灯闪烁,配对成功后熄灭.
低压指示 : 红色指示灯闪烁表示进入低电压状态需充电.
充电指示 : 红色指示灯点亮,充满电后熄灭.
Capslock指示：绿色指示灯点亮.
0.7mA
20
80
1.5mA
269.3x97.4x7.9mm
142.7x97.4x16mm
165
Input: 5V/50-100mA
Power : Slide the keyboard on/off swith to on, the green is visible for seconds.
Bluetooth : Choose the mode, the blue light is visible for seconds.
Pairing : Press Fn+C, Blue light flash. When connected, the lights turns off
Low-Battery : Red light flash
Charging : Red light on. When fully charged, the light turns off.
Capslock : Green light on
Slide the keyboard on/off switch to on, select the
bluetooth model when green light is visible. Then
press Fn+C, start to pair when the blue light is flashing.
Slide the keyboard on/off switch to on, select the
bluetooth model when green light is visible. Then
press Fn+C, start to pair when the blue light is flashing.
Slide the keyboard on/off switch to on, select the
bluetooth model when green light is visible. Then
press Fn+C, start to pair when the blue light is flashing.
Slide the keyboard on/off switch to on, select the
bluetooth model when green light is visible. Then
press Fn+C, start to pair when the blue light is flashing.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.