Instruction Manual

ManualsBrandsShenzhen Deji Innovation Industrial ManualsElectronicsPet polisher

Instruction Manual

Please read the quick start before beginning.

Thanks for purchasing!

The dog training collar is designed to let dogs live safely, happily and get along with

people more harmoniously.

Warning

Do not use with aggressive dogs.

Aggressive dogs can cause severe injury and even death to their owner and others. If you

are unsure whether this product is appropriate for your dog, please consult your

veterinarian or certified trainer.

Caution

Safety during on-leash training.

It is vitally important that you and your dog remain safe while learning during on-leash

training. Your dog should be on a strong leash, long enough for him to attempt to chase an

object, but short enough for him not to reach a road or other unsafe area. You must also

be physically strong enough to restrain your dog when he tries to chase.

Caution

Risk of skin damage.

Please read and follow the instructions in this manual. Proper ﬁt of the collar is important.

A collar worn for too long or made too tight on the pet’s neck may cause skin damage

ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

 Avoid leaving the collar on the dog for more than 12 hours per day.

 When possible reposition the collar on the pet’s neck every 1 to 2 hours.

 Never connect a lead to the electronic collar; it will cause excessive pressure on the

contacts.

 If a rash or sore is found, discontinue use of the collar until the skin has healed.

 If the condition persists beyond 48 hours, see your veterinarian.

 This product is not a toy, please keep away from children.

 This product is only for use with healthy dogs.

Summary of content (10 pages)

PAGE 1
Instruction Manual Please read the quick start before beginning. Thanks for purchasing! The dog training collar is designed to let dogs live safely, happily and get along with people more harmoniously. Warning Do not use with aggressive dogs. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer. Caution Safety during on-leash training.
PAGE 2
Overview Remote A. Shock Level + B. Shock Level – C. On/Oﬀ Button D. Tone Button E. Vibration Button F. Shock Button G. Charging Port Receiver Collar H. Contact Points I. On/Off Button J. Charging Port (with cover) K. Contact spring sheet Setting Up the Product Before you can use the Dog Training Collar, you must set up the product as below steps: 1. Charging the Remote and the Receiver Collar. 2. Prepare the Remote and turn it on. 3. Prepare the Receiver Collar and turn it on. 4.
PAGE 3
1. Plug in and fully charge the Remote and the Receiver collar. 2 hours charging time is sufficient for battery to be fully charged. 2. When full charged, the red LED on the Receiver Collar will become green. The Battery Display of the Remote will stop cycling and appear full. 3. Please replace the rubber cover when the Receiver Collar is full charged. Tips: 1. Excessive charging will shorten battery life. Only charge them when batteries are low. 2.
PAGE 4
Assembly Collar Please refer to the picture to wear the collar on the dog's neck. Adjust the length of the collar. Turn on the Receiver Collar  Press the On/Off Button the Green LED light comes on.  In normal mode, the Green LED will flash every 2 seconds, indicating the Receiver Collar is on and ready to receive a signal from the Remote.
PAGE 5
Shock: sends 1-16 adjustable levels of static stimulation to the Receiver Collar. Slide up, control dog 1, slide down, control dog 2. Short press to turn on, long press to turn off. Press to increase the Shock Level Press to decrease the Shock Level. Note: The Shock Level can be adjusted from 1 to 16 levels , please adjust it properly as per your dog’s reaction. It is not recommended to press and hold the Vibration/Shock Button physical or psychological hurt to the dog.
PAGE 6
Pairing a Second Collar with the Remote 1. Use the Button on the Remote to select Dog 2. Then follow the above pairing steps from 2-4. Dog Training Selecting The Contact Points and The Contact spring sheet For the best results, select the correct Contact Points based on your dog’s coat. You can use the Contact point separately, or use the Contact point and spring at the same time. Collar Fitting Please fit the collar properly so that the Contact Points press firmly against the dog’s skin.
PAGE 7
Product Specification Battery Type Lithium battery Battery Life(typical use) Remote: 27 days Receiver: 11 days Remote Waterproof Rating Receiver Waterproof Rating Non-Waterproof(Keep away from water) IEC 60529 IPX7, waterproof Operating temperature range From 0-40℃(from 32-104℉) Wireless Range Max-300m(984 feet) The unit need to be charged under any of below situations 1. The indicator light on the Receiver Collar is emitting a red color every 2 seconds or flashes rapidly. 2.
PAGE 8
How long can I continuously Vibration/Shock to my pet? deliver The maximum amount of time you can press the Vibration/Shock Button and deliver Vibration/Shock to your pet continuously is 10 seconds. After this, there’s a time-out an Vibration/Shock cannot be delivered for 5 seconds. After the 5 second time-out period, Button can be pressed and Vibration/Shock delivered again. can be Troubleshooting Guide My pet does not respond when I press a  button. Make sure the Receiver Collar has been turned on.
PAGE 9
when any button is pressed on the remote, ensure that the batteries are charged properly.  If the first two solutions did not resolve your problem, Refer to “Pair the Remote and the Receiver Collar” Warranty and repair information 1- Year Limited Lifetime Warranty The original purchaser for this unit is provided with 1-YEAR WARRANTY. The warranty begins from the date of purchase. For the first year, coverage is for both Parts and Labor on warranty repair services.
PAGE 10
the unit has been altered or an unauthorized person has damaged the unit while attempting repair work. We reserve the right to retain and discard any parts or accessories that have been found damaged upon replacement and repair. Procedure for Repair Work If the unit is malfunctioning, please refer to the “Troubleshooting Guide” in the quick start before sending it back for Service. The cost of shipping products under warranty back is the customer’s responsibility.