User's Guide
Statement
Thank you for purchasing our product! This quick user guide will talk about main
usages of the product.More information can be found on our website and the help
center. This user guide may contain inaccurate content due to hardware and software
upgrade.It is subject to change without previous notice.
Safety Caution
Please do not put any uid container on the product.
Please use the product in ventilated environment and prevent blocking the vents.
Please use included power supply with the product to prevent damage to the
product.
Please use the product under its standard working temperature and humidity.
(advised in this manual or distributor’s website)
Dust on PCB may cause short circuit.It is suggested to clean the dust on PCB
timely to make the product work properly.
Please obey the regulation and policy in your country and area during the
installation of this.
NVR
IPC
Wireless Mini NVR kit manual
<
Antenna port:Dual antennas expand the WIFI range;
WAN port: Connect the NVR to the Internet;
TF card slot: TF card interface;
HDMI interface: Connect to high-denition TV;
USB port: Connect mouse and U disk;
Power supply: DC power input (12V 2A);
RESET: Press and hold for 3 seconds to reset (clear the password, network and
other settings, do not clear the camera channel, release the button and restart to
take eect), continue to press the reset button for 10 seconds to reset all (clear
the password, including all settings such as camera channels and so on);
Connect the system as shown in the steps below
System wiring diagram
System connection and installation
Open the hard disk cover on
the back of the chassis and
remove the cover.
Align the hard disk socket with the
wiring port on the NVR, insert the
hard disk, and pay attention to the
direction of the hard disk.
Use TM3*6 silver screws to lock the
silver disk to the hard disk cover
Use KM2*6 silver screws to lock the
hard drive cover to the rear case.
Insert one end of the HDMI cable into the HDMI port of the NVR rear panel, and
the other end into the HDMI port of the TV or monitor;
Insert the USB mouse into the USB port on the NVR rear panel;
Connect one end of the network cable to the WAN network interface of the NVR
rear panel, and the other end to the home router or network access point;
Connect the power adapter connector to the power socket on the NVR rear panel,
and then insert the adapter into the surge protector or uninterruptible power
supply (UPS); make sure that the surge protector or uninterruptible power supply
(UPS) switch is ON, After a few moments, the NVR splash screen will appear on
the screen;
Press and hold the power button of the camera for 2 seconds to turn it on.
Hard disk installation
Configure WNVR on TV or Monitor
After powering on, please follow the steps of the setup wizard to complete the
settings of language, network, time, view real-time screen, password, hard disk
and download APP and device. If you see the prompt "Network status is good!" in
the network setup wizard interface, it means your recorder has successfully
connected to the Internet.
(Tips: If there is no Internet near your video recorder device, you can also choose
to use it without connecting to the Internet. This method will make it impossible to
use the mobile APP to watch the video from a long distance.)
Menu bar
Right-click and you'll go to the main menu, right-click again to exit the menu or
go back.
Split screen selection:
Change the view state, you can choose to view
multiple or single cameras.
Video playback: Enter the video playback interface to play the recorded
video.
Camera Settings: View the settings related to the added camera.
System Settings: Manage all system settings.
Channel Sort: Adjust the camera channel sorting order.
Device Diagnosis: Diagnose camera status, signal and rmware version.
Network Settings: View your device's network connection.
Exit the system: logout, restart, shutdown functions.
System Settings
Channel Toolbar
Right click on the mouse → select System Settings: You can modify system
-related settings.
General settings: Set language, display resolution, audio volume and view rmware information.
Camera settings: All camera settings, alarm settings, recording settings.
Date/Time: Set device time, date and time zone information.
Network settings: Network connection to router settings, wireless channel settings.
Device Diagnosis: Device and added camera status detection and diagnosis.
Storage settings: View hard disk or TFcard information and format.
Move the left mouse button to the corresponding channel, and the toolbar at the bottom of the pop-up
channel will be activated. Click the corresponding icon to enable the corresponding function settings.
From left to right: Audio output switch button, camera light control
and color adjustment button, PTZ control button, talkback button,
channel full-screen playback button.
3
Recording settings
Right click on the mouse ĺ select camera settings ĺ select recording mode on
the right side of the interface
Camera working mode
The battery camera includes three modes: Best power saving, best video
recording, and always video recording;
The constant power camera includes two modes: constant recording and event
recording; the specic mode function introduction is entered into the setting
interface for detailed viewing, and the corresponding working mode is selected
according to the usage scene of your device.
Smart detection settings
Right click on the mouse button ĺ select camera settings ĺ enable smart
detection on the right side of the interface, click smart detection settings.
You can set the camera's detection area, sensitivity level, detection type
(humanoid), humanoid frame switch and other functions;
Smart detection period setting
Right -click on the mouse ĺ select camera settings ĺ detect time period
settings on the right side of the interface.
During the set time period, the device will detect the motion and start recording,
here you can set any time period you want to record, such as 0:00:00-23:59:59
every day , which is 24h*7 days of recording; video recorder When the hard disk
is detected, the system defaults to record 24h*7 days.
1
2
Video Playback
1
1. Right-click on the video preview interface and enter the playback interface, it
will automatically start retrieving the video of the day (default video playback);
2. Select the video playback type (video playback or smart playback), select the
date and channel, and select the recording type (movement, timing, humanoid),
and the recording will be retrieved in real time;
3. Function introduction:
QUICK USER GUIDE
Button description: Play; Fast forward 2 times, 4 times, 8 times;
Switch between 1 and 4 channels; Play in full screen;
Mini NVR can be combined with dierent cameras to form a kit.
The interface description below only takes common cameras as an example. Please
refer to the actual interface position of the camera in the package.
Antenna: for wireless signal transmission
DC Port: Input power 12V 1A;
Reset button: Press reset button for 5 seconds to restore factory setting and enter
into matching-code mode.
Status light:
Unbright: IPC system is not ready or abnormal
Flash: IPC is in the code-matching state
Long time bright: IPC and NVR have been coded, the connection status is normal
Slow Flash: IPC is coded with the NVR, but the connection is disconnected
Note: In night vision mode, the device is normal for 5s, the indicator light will be
turned o to prevent light interference.
DC 12V
USB
HDMI
WAN
RST
TF
1
Antenna
Base
Speaker
Human InfraredSensor (PIR)
Lens
microphone
hard photosensitive
NVR
,3&DPHUD
3RZHU
86%,QWHUIDFH
0RXVH
&211(&7725287(5
+'0,2XWSXW
0RQLWRU
on
of
the
hard
dis
Product name: NVR Model: NVR-1008M-b
Company: 4IFO[IFO%$5JNFT5FDIOPMPHZ$P-UE
Address: 'MPPS#VJMEJOH++JODIBOHEB*OEVTUSJBM;POF4IBOHXFJ7JMMBHF
;IBOHLFOHKJOH(VBOMBO5PXO-POHIVB/FX%JTUSJDU4IFO[IFO$IJOB