User's Manual

USER MANUAL
H2B-02Pro
Dual Hub
motor Long
board
Power button
Front truck
Heat sink
Battery case
Drive truck
Deck
Charge port
LED light
2
1
4
5
6
3
7
8
1
3
5
7
2
4
6
8
PARTS DIAGRAM REMOTE CONTROL
PAIR INSTRUCTION SPECIFICATION
USER MANUAL
At the first step, the Board and Remote must be paired.
Before starting, to ensure the Board and Remote are turn
off.
Turn on the board
Press the power button for 5 seconds,
then the power button light will flash.
Reverse button
Power switch
100% of the battery left
50% of the battery left
Signal indicator
10% of the battery left
The battery indicator of remote
Pair button
Speed mode toggle
High
Middle
Low
Speed control
1 2 3 4
5
6
7 8
PREPARATION
SAFETY INSTRUCTIONS
The electric skateboard is not a toy, should be treated
with appropriate caution. Always practice safety first-as
it is possible to lose balance and cause a collision or fall.
Ensure that you use the board in a safe appropriate
environment, and always wear appropriate safety gear.
Safety Gear: we recommend that you wear full safety
gear while riding. Please wear a suitable skateboard
helmet, elbow pads, knee pads, and gloves.
Wear shoes: Flipflops or similar loose footwear are not
suitable for riding wear.
The skateboard is designed for rider over 10 years old
and above.
Only one person riding for each skateboard at a time.
The maximum load of the board is 150kg. Exceeding this
weight will compromise the structural integrity of the
skateboard, as well as remote and functionality,and may
cause board damage, losing control or other breakage.
Please observe your local traffic laws and regulations.
The board is designed to drive on flat and paved
surfaces. Avoid driving on sand, gravel,mud, rugged or
open ground. Do not drive on slippery ground, such as
snow, ice or wet ground.
Keep fingers, hairs, and clothing away from motors,
wheels and moving parts.
Do not open or tamper with electronics housing.
Electricshock is possible and this also voids the
warranty.
10 +
150
4. Please start with the low speed
mode to be familiar with the
accelerate and brake of the
skateboard.
5. Please stop riding by remote
control brake operation,then get
down your front foot at first and
then get down your back foot.
3. Confirm the position on the
skateboard, The feet stand on
the widest front and back
skateboard.
2. Confirm the front direction of the
skateboard
Thank you for buy our electric skateboard
Do note that an electric skateboard is not a
toy. Please take time to learn it and read this
manual carefully. Particularly the safety
instruction pages.
We hope you will enjoy this product and have
lots of fun with it in the future
Charge port
Accelerate
Brake
Turn on the remote,then press the pair
button. the signal indicator will flash and
the power button light will flash with
same frequence. Then means the
paired successfully.
Push the joystick, forward to test the accelarate and
backward to test the brake. After tested all function work
normal you can start your riding.
1. Be sure that wear a helmet and
safty gear when you ride it
Inner Box Size
Product Size
Charge
Type
Capacity
Voltage
Deck
90mm
8 layers Canadian maple
Lithium Battery
4 hours
2.4GHz
14M
970*265*125mm
1025*310*170mm
Outer Box Size
1050*325*195mm
G.W.
N.W.
Type Hub motor *2
Max load
Speed
Specification
Motor
Weight
Wheel Size
Battery
Remote
Mileage
Watts
36V
6000mAh / 7500mAh
450W*2
15°
150KG
35KM
8.3KG
9.6KG
38KM/H
Dual Hub Motor
Climbing ability
Valid range
Frequency