WIRELESS HD SENDER USER MANUAL EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with you local authority or retailer for recycling advice.
Important Information Please read this user manual before you use this product, it contains all the notes and important things regarding operating this product.In accordance with the safet precautions and operating instructions listed on this user manual, our applies provided the product is handled properly for its intended use, but may not apply to below cases: ● Repairs or product modification and alterations have been executed by unauthorized personnel.
CONTENTS About The Instructions 01 CONTENTS About the instructions 02 Brief introduction 02 Packing List 03 Interface Introduction 05 Wireless HD Transmitter introduction(CV6608, CV8801, CB8808, CB2601) 05 Wireless HD Receiver introduction(CV6620, CV3801) 07 Installation and Use 09 Connect to HD player 09 How to connect to PC 10 CB2601 Loop Output Installation Instruction 12 Installation instructions for CB3801 14 Basic Function 16 IR Remote Extension Connector Instruction 16 Un
TX:CV6608 AV Sender Packing List Wireless HD Transmitter CV6608 x 1 Base x 1 IR Remote Extension Connector X 1 Power Supply (5V/2A) x 1 RX:CB3801 Please check the packing list carefully after unpacking, if any part is missing, please contact your dealer. Accessories of all models are subject to the following packing list.
Interface Introduction CB2601 Wireless HD Transmitter Model: CB2601 Transmitter Interface Introduction CV6608 Wireless HD Transmitter Model: CV6608 VGA IN NETWORK INDICATOR VGA 2 INDICATOR NETWORK INDICATOR IR slot VIDEO INDICATOR VIDEO INDICATOR HDMI 1 INDICATOR HDMI OUT MINI USB IN AUDIO IN IR HDMI IN CODE KEY DC IN HDMI IN DC IN CODE KEY CB8801 Wireless HD Transmitter Model: CB8801 CODE KEY VIDEO INDICATOR NETWORK INDICATOR MINI USB IN HDMI IN CB8808 Wireless HD Transmitter Model: CB8808
CB8801/CB8808 On: The wireless network connection between transmitter and receiver is successful . Flash Slowly: Transmitter is ready for connecting. Flash Rapidly: The device is faulty. 9. VIDEO INDICATOR On: The HD AV source is connected successfully. Off: The HD AV source is failed to connect. 10. HDMI INDICATOR ON:HDMI input is selected currently. OFF:HDMI input is not selected currently. 11. VGA INDICATOR ON: VGA input is selected currently. OFF: VGA input is not selected currently. 12.
Product Installation Instructions Connect to HD player 1. Install the transmitter and receiver respectively on base. *To avoid affecting the transmission distance and image effect, please do not place any article on or beside the transmitter. 7.Wait for 15 to 25 seconds, the network and video indicators will turn on, after that, the video connection is successful. TV screen display player's broadcasting content and OSD information on TV screen will be prompted as “NETWORK CONNECTED, VIDEO CONNECTED" RX:1.
Vid Ne tw 5. Wait for 15 to 25 seconds, the network and video indicators will turn on , the video connection is successful. OSD information on projector (HDTV) screen will be prompted as “NETWORK CONNECTED, VIDEO CONNECTED" and display video source content of PC/ Laptop's desktop. eo ork VGA adapter VGA TX:CB8808 VGA Interface Transmitter AUDIO OUT Audio cable USB USB cable RX:1.x.xx TX:1.x.xx 1920x1080P Fre q : 5 x x x N E T W O R K C O N N E C T E D. V I D E O C O N N E C T E D.
3. Connect“HDMI OUT”port on CB2601's front panel to the HDTV1 by the HDMI cable, the TV screen will show the content of default input source. Switch VGA / HDMI input source by pressing code matching key shortly. 1. Screw CB3801 with the bracket, rotate the screw clockwise until fix it, adjust the receiver up and down, then fix it with proper angle, and twist the wrench clockwise to fix the direction of receiver. 1.
3. Wait for 15 to 25 seconds, the network and video indicators will turn on, the video connection is successful. OSD information on projector (HDTV) screen will be prompted as “Connected to CB3801" and display video source content of PC/ Laptop. Notice: As to the specific model of transmitter's installation steps, please refer to the product installation instruction in this chapter. Basic Function IR Remote Extension Connector Instructions Use HD player's remote control at TV's side to control HD player.
Unicast (point-to-point) Code Matching Procedures Code matching are defult set in factory ,user do not need to repeat this operation. Operation of re-matching code for TX and RX 1. Power on transmitter and receiver. 2. Use tweezers or paper clips to press the code key of transmitter and receiver for 5 seconds and then loosen from the code key. 3. Wait for 30 to 60 seconds, the network indicators of transmitter and receiver will turn on, after that, the code matching is successful.
5. Wait for 15 to 25 seconds, the network and video indicators will turn on, the OSD information on TV screen will be prompted as the following picture and the disappear in 3 seconds. Connected to Stick0203 Add New Video Source (WHDI Product Code Matching) WHDI supports multiple transmitters with one receiver. You can add additional transmitters as refer to the following steps: 1.
Rename Video Source Select Video Source 1. Press [Source] key, the list of video sources will be displayed on screen. 2. Use [UP]/[DOWN] direction keys to choose a video source, press [OK] key to confirm connecting to the one selected. Select Video Source Connected to Stick0203 Stick0203 SONY BD DVB 1. Press [MENU] key and choose "Modify Video Source " from main menu. 2. Select the video source needed renaming from the video source list and press [OK] to confirm.
HID Remote Control Operation Instruction * Product model suffix with a "H" means supporting HID function. Supported model: CV6620H, CB8801H, CB8808H, ,CB3801H,CB2601H Function Instruction Installation of HID Driver 1. Run the driver installation package , at the first installation, the language selection dialog box will pop up as follows: HID Keyboard/Mouse Remote Control function support users to use keyboard/mouse at receiver(Monitor) side to control the PC at transmitter side.
3D Video Transmission * Product model suffix with a "D" means supporting 3D video transmission function. Supported model: CV6620D, CV6608D, CB8801D, CB3801D,CB2601D Function Instruction 3D Video Transmission requires transmitter and receiver's hardware supporting of wireless transmission for 3D audio and video signal. Function Application 1.Please make sure that both of the transmitter and receiver with the Model No. can support 3D video transmission function. 2.
Graphic Card Setting Appendix Windows 7 System OSD (On Screen Display) 1 2 3 4 5 6 RX:1.5.44 TX:1.5.44 1920*1080 Freq:5230 NETWORK CONNECTED. VIDEO CONNECTED. 1. Receiver software version number; 2. Current video resolution; 3. Network connection status indicator: Network Connecting: Being in the process of network connecting; Network Connected: Network connection is successful. 4.
4. Select "The same on both displays (Clone) " or "Configured independently from each other (Dualview) ", click "Apply"; 5. When computer screen shown on the display device, click "Yes" to save the setting. 6. As below picture show, select the "Change resolution" option, you can modify the computer output resolution as dragging the "Display Resolution" progress bar. 7.
Indicator Description Model Indicator Indicator Status ON Network Indicator Windows XP System (INTEL Graphic Card Series) TX:CV6608 1. Right-click the mouse on the desktop, select "Graphics Properties .."; 2.
Product Specifications Indicator Indicator Status ON Network Indicator Video Working Status successful between transmitter and receiver. Flash Slowly — Receiver is ready for connecting. Flash Rapidly — The device is faulty. ON — The video source is connected successfully Indicator OFF CV6608 — The wireless network connection is — The video source fails to be connected Tramsmitter Model CB8801 5.15~5.25, 5.25~5.35, 5.47~5.725, 5.725~5.
Trouble Shooting Possible Reasons: Solutions: Transmitter is not electrified. Power on transmitter. Transmitter or receiver is not placed erectly. Place the TX or RX onto the base and maintain them erectly. Transmitter or receiver is not placed erectly. Place the TX or RX onto the base and replace them erectly. The transmitter and receiver are out of effect range. Move the receiver closer to the transmitter. The transmitter and receiver are too far away.
Possible Reasons: Solutions: Several solid walls partition transmitter and receiver. Reduce the number of solid walls between TX and RX. There are too many obstacles between TX and RX. Move the receiver closer to the transmitter. Haven't matched the code of TX and RX. Rematch the code of transmitter and receiver. Transmitter or receiver failure Please contact your distributor. Transmitter Indicator status of wireless connection is on, but video Indicator is off. Receiver and TV are not connected.