WIRELESS HD TRANSMISSION SYSTEM USER MANUAL EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with you local authority or retailer for recycling advice.
Important Information Please read this user manual before you use this product, it contains all the notes and important things regarding operating this product.In accordance with the safet precautions and operating instructions listed on this user manual, our applies provided the product is handled properly for its intended use, but may not apply to below cases: ● Repairs or product modification and alterations have been executed by unauthorized personnel.
CONTENTS 01 About The Instruction CONTENTS About the instructions 02 Brief introduction 02 Packing List 03 Interface Introduction 05 Wireless HD Transmitter introduction(CV6608, CV8801, CB8808, CB2601) 05 Wireless HD Receiver introduction(CV6620, CV3801) 07 Installation and Use 09 Connect to HD player 09 How to connect to PC 10 CB2601 Loop Output Installation Instruction 12 Installation instructions for CB3801 14 Basic Function 16 IR Remote Extension Connector Instruction 16 Unica
Packing List Interface Introduction Please check the packing list carefully after unpacking, if any part is missing, please Transmitter Interface Introduction contact your dealer. Accessories of all models are subject to the following packing list.
1. MINI USB INPUT PORT connect Mini USB input port to the computer’s USB port or the 5V/1A power adapter by the USB cable for power supplying. * HID Keyboard/Mouse Remote Control function is supported when connected the mini USB input port to the computer. 2. HDMI IN Connect to the HDMI Output port of a HD AV source device. 3. VGA IN Connect to the VGA port of computer. 4. AUDIO IN Connect to the audio output port of computer by the audio cable. 5.
Product Installation Instructions How to connect to PC 1.CB8808 should be connected with the VGA port through the VGA adapter. 2.Connect CB8801/CB8808 to Laptop/PC USB port by the USB cable; connect the Audio In port of transmitter with Audio Out port of Laptop/PC by the audio cable. Installation instructions for CB3801 1.
3. Wait for 15 to 25 seconds, the network and video indicators will turn on, the video connection is successful. OSD information on projector (HDTV) screen will be prompted as “Connected to CB3801" and display video source content of PC/ Laptop. Notice: As to the specific model of transmitter's installation steps, please refer to the product installation instruction in this chapter.
5. Wait for 15 to 25 seconds, the network and video indicators will turn on, the OSD information on TV screen will be prompted as the following picture and the disappear in 3 seconds. Connected to Stick0203 Add New Video Source (WHDI Product Code Matching) WHDI supports multiple transmitters with one receiver. You can add additional transmitters as refer to the following steps: 1.
Rename Video Source Select Video Source 1. Press [Source] key, the list of video sources will be displayed on screen. 2. Use [UP]/[DOWN] direction keys to choose a video source, press [OK] key to confirm connecting to the one selected. Select Video Source Connected to Stick0203 Stick0203 SONY BD DVB 1. Press [MENU] key and choose "Modify Video Source " from main menu. 2. Select the video source needed renaming from the video source list and press [OK] to confirm.
HID Remote Control Operation Instruction Function Instruction HID Keyboard/Mouse Remote Control function support users to use keyboard/mouse at receiver(Monitor) side to control the PC at transmitter side. Note: Since one USB port in receiver can only support one wired keyboard or mouse at a time, there recommend to use the wireless keyboard/mouse set which share one USB wireless receiver connector for this HID function supporting. KRO Installation of HID Driver 1.
Graphic Card Setting Appendix Windows 7 System List of Supported HID Wireless Keyboard/Mouse Model Device Name RAPOO 1800E Device Type Result Mouse+Keyboard OK Lenovo KM4901 Mouse+Keyboard OK Fuhlen U79 2.
4. Select "The same on both displays (Clone) " or "Configured independently from each other (Dualview) ", click "Apply"; 5. When computer screen shown on the display device, click "Yes" to save the setting. 6. As below picture show, select the "Change resolution" option, you can modify the computer output resolution as dragging the "Display Resolution" progress bar. 7.
Indicator Description Model Indicator Network TX:CB8801 Video Windows XP System (INTEL Graphic Card Series) 1. Right-click the mouse on the desktop, select "Graphics Properties .."; 2. Select "Multiple Displays" in "Intel Graphics and Media Control Panel", change " Operating Mode" to "Clone Displays" or "Extended Desktop"; Indicator TX:CB8808 Indicator Model Indicator Indicator Status — The wireless network connection is Flash Slowly — Transmitter is ready for connecting.
Product Specifications Tramsmitter CB8801 CB8808 Transmission Frequency 5.15~5.25, 5.25~5.35, 5.47~5.725, 5.725~5.850 (GHz) Frequency Stability ±10PPM 20MHz / 40MHz Bandwidth Standard Protocol HDMI 1.3,HDCP 1.2 Receiving Sensitivity ≤- 75dBm System Latency ≤1ms ≤1ms TX/RX channel 2 TX / 1RX 2 TX / 1RX ≤- 75dBm Transmission Power 13±2dBm 10 ±2dBm Transmission Distance ≥25m ≥25m Power Supply 5V /1A 5V /1A Dimensions (W x D x H) 98 x 29 x 14.5 (mm) 91.5 x 31x 17.
Trouble Shooting Possible Reasons: Solutions: Transmitter or receiver is not placed erectly. Place the TX or RX onto the base and maintain them erectly. The transmitter and receiver are out of effect range. Move the receiver closer to the transmitter. Power on transmitter. Place the TX or RX onto the base and replace them erectly. The transmitter and receiver are too far away. Move the receiver closer to the transmitter. Several solid wall partition TX and RX.
Possible Reasons: Solutions: Several solid walls partition transmitter and receiver. Reduce the number of solid walls between TX and RX. There are too many obstacles between TX and RX. Move the receiver closer to the transmitter. Haven't matched the code of TX and RX. Rematch the code of transmitter and receiver. Transmitter or receiver failure Please contact your distributor. Transmitter Indicator status of wireless connection is on, but video Indicator is off.