C匡 二 CRYST L A VIDEO PROZ Zero Latency Channel Scan Wireless Video Transmission System ^ 3PAP 翌一 EU Environmental Protection Waste electrical products should not be disposed of with household waste.Please recycle where facilities exist.Check with you local authority or retailer for recycling advice.
Important Information Please read this user manual before you use this product, it contains all the notes and impor tant things regarding operating this product. In accordance with the safety precautions and operating instructions listed on this user manual, our applies provided the product is handled properly for its intended use, but may not apply to below cases: • Repairs or product modification and alterations have been executed by unauthorized personnel.
- Please read this manual carefully before you use this product and retain it properly for future reference.
- Packing List Please check the packing list carefully after unpacking. If any of them is missing, please contact your seller. ----Wireless HD Transmitter•1 a Antenna•2 Mushroom Antenna *2 * Articulating Magic Arm with Cold Shoe (7")•1 SDI Cable *1 tJP Wireless HD Receiver *1 Antenna•s D-Tap to 2-pin LEMO Cable *1 SDL Cable *1 * The shape, mark printing and accessories of all models are subject to the actual product you received. 02 _I - Specification Specification Frequency 5.1-5.
.... Structure & Interface Transmitter: 7118 I Antenna Sockets TX _ Transmitter Interface Description I I OLEDScreen Displays Channel info, video format, battery capacity, fan status, and other information.
Structure & Interface RX Receiver: 3118 Antenna Sockets C呵 ,一 ,一 I I J OLED Screen Antenna Sockets PUSH _ Receiver Interface Description Funcfon I OLEDScreen Displays Channel info, video format, battery capacity, fan status, and other information.
.... Mounting 2. Powered by the V-mount battery or DC power input. See below: For transmitter 7118 1. Install the antennas and make sure they are tightened. The angle between Battery Installation the transmitter's two antennas should be perpendicular to achieve the best wireless transmission performance.
For receiver 3118 3. The transmitter can be installed on camera with 1. Install the antennas and make sure they are tightened. The angle between the V-Mount or via 1/4 the receiver's two antennas should be adjusted to a 45 ° angle to achieve the screw threads at the best wireless transmission performance. See below: bottom. 4. Connect the transmitter to the video camera/SLR camera with 付 _ I _ __ 贮 sLR t. 勹贮 V 仁'� 矗 HDMI/SDI cable.
2. Powered by the V-mount battery or DC power input. See below: 3. The receiver can be attached to the tripod with the 1/4 or 3/8 screw thread, or it can be Battery Installation attached to the monitor with the magic arm. V-mount battery Receiver , Power Access 1lV 工 厂� Camera Battery 4. Connect the receiver to the monitor or other monitor equipment with HDMI/SDI cable.
- Power Supply and Start-Up 1. The transmitter can be powered with the following methods: b. Powered by D-Tap to 2-pin LEMO cable via other power sources. a. Install the V-Mount battery on the back of the transmitter. Both the camera and the transmitter can be powered by the V-mount battery.
2. The receiver can be powered with the following methods: a. Powered by V-mount battery. b. Powered by D-tap to LEMO power cable via other power sources. 3. After power is in use, the transmitter and the receiver takes approximate 10s to start up. When this kit boots up, it will automatically connect by default.
- OLED Display Description 3118 OLEO Status 7118 OLED Status Fan Status Fan Status Battery 6.5V Video Signal Video Signal CH Battery Displays battery voltage Fan Status $ Signal Strength 丫:••• OVIDEO Operating Channel Operating Channel Status [ 6.
- Channel Switching Operation 1. Press the Up or Down Button Receiver's Menu Button: Long-press for 3 seconds to enter the menu interface. The configurable settings are: channel scan, color space output, language settings, firmware version number. 2. Then press the Menu button to confirm. Important Reminder: When switching channels, please note that the transmitter and the receiver must be set to the same channel so they can stay connected.
- Precautions Installation Height and Distance c. When this kit and other wireless devices are operating simultaneously, in order to stop this kit from interference, please adjust distance at least 2 meters. a. The transmission range is up to 800m in wide-open, unobstructed, and optimal antenna installation cond代ion. This distance is shortened in non-optimal installation conditions.
__ - Troubleshooting HDMI/SDI Connection and Antenna Installation Recommendations a. First connect the HDMI/SDI cable, and then switch on the power source. b. These antennas are demountable. Install the antennas and make sure they are I No signal input tightened. Then start up the power source. If turning on the power source before Transmitter and receiver cannot establish a connection Solution I Examine whether the product's antenna is installed.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.