SWIFT 800 Wireless HDMI Video Transmission USER MANUAL This user manual applies to: Transmitter: 7072 Receiver: 3072 Version: 1.0 2019.01.
CONTENTS Foreword 01 Brief Introduction 01 Features 01 Packing List 02 Structure & Interface 03 The Transmitter 7072 03 The Receiver 3072 05 Product Installation 07 Digital Tube Status Indication 11 Operating Instructions 12 Application Case 13 Product Specifications 15 Troubleshooting 16
Foreword - Please read this manual carefully before you use this product and retain it properly for future reference - If there is any doubt or difficulty in the process of product usage, please feel free to contact us or the dealer. - The company reserves the authority to amend the specification.
Structure & Interface Transmitter 7072 Interface Introduction Transmitter:7072 Link indicator 1. Link indicator: Used to indicate the network working status of the product. Video indicator Antenna interface 3. Digital LED: Used to display the current working status and working channel of the transmitter. Digital LED CH button Mini USB 2. Video indicator: Used to indicate the video transmission working status of the product. Mode button 4.
Receiver 3072 Interface Introduction Receiver:3072 1. Link indicator: Used to indicate the network working status of the product. Link indicator Video indicator Antenna interface 3. Digital LED: Used to display the current working channel of the receiver. Digital LED CH button Mini USB 2. Video indicator: Used to indicate the video transmission working status of the product. Mode button 4. CH button: a: Short press to switch the frequency channel; b: Press and hold (3s) to turn on / off the fan.
Product Installation 3. The transmitter is mounted on a SLR camera and rotated clockwise. Connect the HDMI interface of the transmitter to the HDMI interface of the 7072 Wireless HD Transmitter Installation Instructions SLR camera via the HDMI cable (as shown in the figure). 4. Turn on (SLR camera, and transmitter) the power. 1. Install the antennas on the transmitter, turn it clockwise, and tighten the antennas.
3072 Wireless HD Receiver Installation Instructions 3. Install the receiver on the monitor. Connect the HDMI cable. Turn on the power (receiver and monitor power). 1. Install the antennas on the receiver, turn it clockwise, and tighten the antennas. Adjust the direction of the receiver antennas to assume an upright parallel state (as shown in the figure). 2. The receiver is equipped with a battery (as shown in the figures).
Digital Tube Status Indication Operating Instructions Transmitter / Receiver Digital Tube Status 1. Button function definition: LINK indicator VIDEO indicator Channel button (CH): channel switching function Mode button (Mode): Mode switching function 2. Operating instructions: Frequency channel setting, short press CH button to switch the operating frequency channel; Digital tube display Decimal point Fan ON/OFF, press and hold the CH button (3s) to turn on / off the fan. 3.
Application Case Connecting to transmitter... 1. Set the transmitter and receiver to the same frequency channel . 2. The transmitter and HD source device are connected and powered by the HDMI cable. 3. The receiver and monitor are connected via an HDMI cable. OSD display 5. Wait 25~35 seconds, the receiver’s network indicator and video indicator are always on, and the monitor displays the camera’s monitor screen. The OSD display is shown in the figure below.
Troubleshooting Product Specifications Issue 7072 Item 5.190-5.23 0/ 5.755-5.795 (GHz) Modulation mode OFDM Channel bandwidth 40MHz HDMI protocol HDMI 1.4 Power consumption 5.5W System Latency 70ms Antenna mode 2T2R Transmission range 800ft 4.8W Operating voltage DC (7~36V) Battery: SONY NP-F970 or compatible series Dimensions 100 x 68 x 22.
FCC Statement Sound Image Issue TV images are not clear, with noisy point or mosaic Troubles & Possible Reasons Solution The transmitter or receiver is not placed upright. Insert the transmitter or receiver into the base and keep it upright. The distance between the receiver and the transmitter is too far. The receiver and transmitter are separated by multiple solid walls. Move the receiver to a position closer to the transmitter..
