OT240M Baby Monitor User Manual Components Built-in MP3+4G TF card with songs and stories; User-friendly menu; Two-way talkback to comfort baby. One User Manual One parent unit One rechargeable Ni-MH battery for the parent unit One baby unit One power adapter One USB connected adapter One Pulse Oximeter (including one SpO2 probe) Two batteries for Pulse Oximeter Settings Step 1: Connect the baby unit to the power and insert battery pack into parent unit with correct polarity (+/-) as indicated.
Step 2: Toggle the key on the baby unit, press and hold the parent key until the green LED is on. The parent unit is now powered on and the parent unit will search for and link itself to the baby monitor. Baby unit settings 1. Play the next lullaby 3. Play previous lullaby 5. Volume up 7. Power switch 9. USB power jack 2. Pause/play 4. Nightlight 6. Volume down 8. MP3 TF slot 10.
11. Press to access menu settings, press and hold to power on/off. 12. Remote control the camera of the baby unit (turns left/right or up/down). 13. Turn on/off LED Press and hold to talk with your baby. Tips: To turn off LCD screen by pressing button 13 for power saving and more restful sleep at night. Talk with baby by pressing and holding the button 14. Press button 11 to open menu when parent unit and baby unit turned on. Constant LCD light mode and power saving mode are available in second item.
Power Signal SpO2 Value Pulse Rate Value 1. Volume settings Press menu button to access main menu when parent unit is turned on, choose this icon and then increase or decrease the volume of parent unit pressing the left or right direction keys. (Default is Mute) Constant LCD light/Power saving Press menu button to access main menu, choose this icon to set the display mode by pressing left or right direction keys. (The light under Power saving mode will self-adjust according to the environmental sounds).
Technical parameters Model OT240M Modulation system FSK Frequency 2.4G Channel Screen material 19 2.4” LCD SpO2 Range 35% - 100% SpO2 Alarm Low limit 90% Pulse Rate Range 30bpm – 240bpm Pulse Rate Alarm High limit 160bpm Low limit 70bpm Baby unit battery Dc 6v/2a Parent unit sensitivity Parent unit adapter Aa1800mA 3.6V NI-MH ≤85dBm Parent unit battery DCV / 500mA Battery cycle life Aa1800mA 3.
Technical features Low power indication: Should battery voltage fall below 3.5V, parent unit will alarm and will shut off if below 3.0V. Squelch: automatic filtering environment background noise. Automatic sound trigger: If the sound exceeds 50dB, the baby unit will transmit sound so as to prevent parent from noise interference.
substitute for responsible and proper audit supervision and not intended for use as a medical monitor. Please do not use power adapters that may not fit this product configuration. Please do not expose the baby monitor to extreme cold, heat, wet or direct sunlight. Make sure the baby unit and the adapter cord are always out of reach of the baby, at least 3 feet/1 meter away from the baby or crib, to avoid a possible strangulation hazard.
away from the baby unit; Turn down volume on the parent unit. Problem: Weak sound or mute coming from parent unit. Possible cause: Volume on parent unit or set too low or muted. Solution: Turn up the units closer to each other. Problem: Units may be too far from each other. Possible cause: No signals between units. Solution: Move the units closer to each other. Instructions for Pulse Oximeter Connection Insert the sensor tips into the slots on the probe holders.
Figure 2 Y-type SpO2 Sensor with Rubber Wrap NOTE: Make sure that the silicone button seat fully into the hole in the back of the probe holder. Wrap the oximeter on the leg near ankle with its belts and position the front panel to a proper place for convenient operation, as shown in Figure 4. Wrap up the Y-type sensor onto the baby’s foot by the rubber wrapper, as illustrated in Figure 3.
Y-type SpO2 Sensor with rubber wrapper Pulse Oximeter Figure 4 Placement of the Oximeter and the Sensor It's recommended that wrapping up the sensor onto the baby's first toe if the foot is too thick to be tighten, as shown in figure 5. Figure 5 IMPORTANT: The sensor connection is critical for the signal strength and quality. Try to make LED and PD facing each other in opposite side, so that the light beam is as vertically transmitted as possible and the light path is as short as possible.
Instructions for Operation After all connection are completed, press the Power Button ( ) for 3 seconds to power on the oximeter, referring to below figure. When the oximeter is powered up, the Power Indicator (yellow lamp ) will light constantly. If the heart beat is detected, the Heartbeat Indicator (red lamp ) flashes according with the heart rate.
Distributed by: eH4H LLC 1200 Abernathy Road, Suite 1700, Atlanta, GA 30328 Website: www.Dormebaby.com Tel: 888-741-2224 ext. 2 Fax: 832-442-4000 A division of Tele-H-for H Holdings, LLC FCC Caution. §15.19 Labelling requirements. This device complies with part 15 of the FCC Rules.
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. §15.105 Information to the user.
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
