IPC100 Baby Monitors User Manual Features MJPEG with two-way communications; P2P iOS / Android support; SpO2 and Pulse Rate (PR) measurement; Room temperature measurement; Lullabies; Pictures; Video Night light.
Overview of front side Camera Infrared light Microphone Night light Night light button Pedestal Overview of back side
1. Power switch 2. Micro SD card socket 3. USB interfaces 4. Sarus light 5. Power light 6. Speaker 7. Temperature sensing antenna Photoresistor: Senses light automatically switching from day to night.
Step 2: Click "Next"→ "Next" as shown in below figure. The password is default and tap next.
You can operate the IPC100 and remote control the pan tilt. Step 4: While the IPC100 connected to WIFI or another mobile phone adds IPC100. Open the software of IPC100, to tap "add new camera"→ "LAN searching" (make sure no camera in the camera list), as shown in below figure: Tap "IPC-E8ABFXXXX" and then "Save", the password is default blank. The signal icons " " in blue indicate well connected to the WIFI, as shown in below figure: You can operate the IPC100 and remote control the pan tilt.
till the night light on) 1. Temperature: tap the temperature value to change the unit Centigrade and Fahrenheit. 2. Photos 3. Video recording 4. Photograph 5. Previous song 6. Play & pause 7. Next song 8. Volume up 9. Volume down 10. MP3 11. Talkback 12. Monitor 13. Nightlight 14. Time 15.
Warning: To prevent strangulation with the power cord, always keep the baby unit and the power cord out of baby's reach, at least 1metre/3.5 feet away. Do not use extension cords.
Install mobile phone software Step 1: Connect the mobile phone to WIFI. Step 2: Set the regional Network: open the software --Refresh--Searched IP --Edit. Step 3: Preview--Save--save Step 4: Set the P2P network: P2P-please click here to add the camera.
Step 6: Click the red square → input the password (888888)→ save. Step 7: Click the camera Step 8: The available settings for camera are audio frequency, talkback, video recording, and resolution value, with the function of photographing, cruise, mirror and flip. You can switch among the camera list, video list and instruction at the bottom of the screen. Remark: the video from camera list is connected to the regional network and P2P is connected the outside network.
Technical parameters Model IPC100 Description IP camera for baby monitoring Modulation MJPEG with 2 way audio Frames per second 15~25/s SpO2 Range 35% - 100% SpO2 Alarm Low limit 90% Pulse Rate Range 30bpm – 240bpm Pulse Rate Alarm High limit 160bpm Low limit 70bpm APP / APK Android/iOS Infrared night view Yes AC adapter 6V 500mA Walkie-talkie function Yes Night light function Yes Temperature detect Yes Monitor with motor Yes Other functions Smart size, nice appearance,
transmission. Alarm function: when the measured SpO2 or Pulse Rate value exceeds the preset alarm limit, then the smart phone will activate the audible and visual alarm indications. Infrared night vision function, you can see your baby even he/she is in the darkness. Pleasing nightlight and lullaby to comfort baby. Especially suitable for infant care, elder care, monitoring, etc., it can also be used for general real time security monitoring. Cautions: This product is intended as an aid.
Troubleshooting Problem: Power indicator light not working. Possible cause: Does not switch on; Power is not getting to the unit; Low batteries. Solution: Turn on the units; Make sure the units are connected to the power supply; Replace the batteries. Problem: Power indicator flashing. Possible cause: Not connected well with adapter; Low batteries. Solution: Make sure well connected; Replace the batteries. Problem: Parent unit makes loud noises.
Supplementary Operation Instruction for Pulse Oximeter Instructions for Connection Insert the sensor tips into the slots on the probe holders. Place the sensor tip labeled “LED” into the stationary probe holder on the silicone wrap belt, and place the sensor tip labeled “PD” into the sliding probe holder, as illustrated in Figure 1 and Figure 2.
and the photo- detecting tip (PD) are aiming at each other, then thread the end of wrap belt through the outside slots on the probe holders and tighten the rubber belt with proper force. The final placement is shown in Figure 4. Figure 3 Sensor wrapping up Y-type SpO2 Sensor with Rubber Wrapper Pulse Oximeter Figure 4 Placement of the Oximeter and the Sensor It's recommended that wrapping up the sensor onto the baby's first toe if the foot is too thick to be tighten, as shown in figure 5.
Instructions for Operation After all connection have been completed, press the Power Button ( ) for 3 seconds to power on the oximeter, referring to below figure. When the oximeter is powered up, the Power Indicator (yellow lamp ) will light constantly. If the heart beat is detected, the Heartbeat Indicator (red lamp ) flashes according with the heart rate.
Distributed by: eH4H LLC 1200 Abernathy Road, Suite 1700, Atlanta, GA 30328 Website: www.Dormebaby.com Tel: 888-741-2224 ext. 2 Fax: 832-442-4000 For mobile phone with Android system, please go to Google Play and search "Dorme Baby" to download and install the responding application; For mobile phone with iOS system, please go to APP Store and search "Dorme Baby" to download and install the responding application. FCC Caution. §15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. §15.105 Information to the user.
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver.
