T21 User Manual 1
Content 1 Product Outline ................................................................................................ 1 2 System Parameter............................................................................................. 1 2.1 3 Transmitter Parameter ........................................................................... 1 Product appearance .......................................................................................... 4 3.1 3.2 Transmitter Appearance ................
6 5.2 Staff Paging ......................................................................................... 23 5.3 other special function .......................................................................... 24 Breakdown & Solution .................................................................................. 24 7. FCC Important Note ........................................................................................ 25 FCC Part 15.19 Warning Statement ...................................
1 Product Outline Guest Paging System including: Transmitter+Coaster Pagers. When using, dispatch the Coaster Pager which with the Exclusive Code to the customers. The customer could find a seat to relax or go outside stroll about. When the Dishes are ready or have the empty seat, the staff would input the coaster pager No to notice the customer return. The Customer would notice this by Coaster pager ring, light or vibrate prompt.
Power Supply 12V/ 3A Interface type USB、RS485（Ethernet available） Frequency Customization available Paging number in 40 cache Queuing display 3 digit LED nixie tube Card type RF Card Transmitting Power 0-2W adjustable Antenna External BNC Socket Coaster Pager —999 System Capacity Waiter Numbers——999 Default single key paging ——10 Timely paging ——10 Table 2.1 Transmitter Parameter 2.
Coaster pager 3 digit，001-999 number Alert mode Vibration and sound，with LED flashes Out of Range Alert Alarm when out of the transmitter range Lower Power Buzzer sounds “didi” Prompt Water resistant Surface water resistant design Power supply 2.4V/600mAH Standby Current 500uA Temperature -0℃—+65℃ Table 2.2 Coaster Pager Parameter 2.3 Charger Parameter Overall size 112mm(diameter) × 17mm(thickness) Input DC-12V/1.
Table 2.3 Charger Parameter 3 3.1 Product appearance Transmitter Appearance The Transmitter Panel including the display area, key area, swipe card area and The Buzzer speaker mouth.
Display area keypad Buzzer speaker mouth 3.1 Transmitter Transmitter Interface picture 3.2 Power Swipe Card 485 internet 3.
3.1.1 Transmitter Display Area Divide Current Interface User information Time Icon Indicator From Left to Right : wireless sending, timely paging 、 Open Voice 、 input method Main Information Input the sending Serial No area 3.2 Interface 3.1.2 Transmitter Interface Area explanation Sending message inputting area 1、Current Interface Indication Area This interface is used to indicate the user the current status.
3.2 Transmitter Function 1、Single Call Single call one coaster pager or pager receiver, won't page the other receivers. 2、Class Call Could call in class. One is call the staff pagers, the other is call the staff coaster pager. Once call, the class pagers would ring. 3、Group call It could edit and make a group through the PC software in advance, name the same group pagers in 1 group, then send the message to the transmitter.
special situation the upgrade failed, the system won't be broken down, it could return back to the program code before the upgradation following the below step: In the power cut off status, press the F1 and F2 key simultaneously, then plug the power in, the screen would turn black, then appear the yellow font. When the first line displaying: Reply_original_program...., it indicates that could restore the original backup program.
Battery The charging column Induction Display Pic 3.3 coaster pager 3.3 Coaster pager Function 1、When put the coaster pager on the charger, won't receive the calling data, only charging, the LED light would Marquee cycle flicker to indicate the charging, the Nixie tube showing the pager number. When enter into the charging status, the LED would flicker all the time. When the LED enter into the light all the time, that indicate the charging finished.
command in the transmitter. The prompt voice is long Di...Di and vibration, and the LED flashing. It would enter into the standby status after the acousto-optic vibration Ended. 6、 When the queue number prompt function open, it would send the queue number message when sending the heart beat protocol data. When the queue number decreased, it would prompt by showing current queue number and the pager ID, Long Di....Di and vibration, LED light would flash twice.
and flash showing "LLL" . At this time, the user has to charge immediately. 13、Communicate with the PC software function. The parameter could be set up through the PC software. By the special burning connector download the data into the coaster pager memory. 14、In the transmitter testing mode, all of the coaster pagers receive the testing data. the pager would flash twice for 0.5s in colorful light after got the data. In the coaster pager it could store as much as 7 addresses. It named ADDR1-ADDR7.
4 4.1 Operation Guide Transmitter operation Guide 4.1.1 Paging Customer Interface Sn is the queue serial No. ，Num is the customer's Serial No. In the waiting for fetching the dish mode, Pn stand for persons numbers.In the fetching the dish mode, Pn stand for order message, Cn is the status, wheen it is in green, it means the message has been sent out. Time is the queue record time. 4.
system would position the chosen message automatically, and pitch on, at this time you could Press the SEND key to send. If in the fetching the dish mode, if inputting the SN, it would search according to it, if typing # plus order No. It would search according to the order #. Such as to search the order 1234, just input#1234，if input #125, then it would turn to red which means the wrong typing. 2：use the upper key to move the cursor to the middle message area, the message would be inverse.
picture 4.2 Staff Calling interface In the staff calling interface, the method of inputting SN is the same as paging the customer. The only difference is that the message input in this interface message input box as the sending message. After the number was input, press the "ENT" to enter into the message edition interface, in this interface it would show the fixed message. When the cursor move to the fixed message, it could page turn.
Paging indicator to send. Picture 4.3 input message interface 4.1.
Picture 4.4 Staff Group Paging Interface The staff group paging interface is the same as the single paging. The only difference is that the display content in the main display area. The group displayed in the screen is edited by the operator in advance, and download it in the transmitter. After chosen the group number, the middle area would show the group members number , click "Send" the message would be sent to all of the chosen members.
Picture 4.5 Setting interface In the setup interface, the bottom two input boxes would turn gray. The yellow cursor is valid. Just as the picture shown: the left area is setting item, the right area is the concrete setting content. Using ENT enter the setting content area, ESC to return back to the setting up item. Picture 4.6 is the power setting up interface. Choosing the setting up item，then click ENT to enter into the concrete setting item, then the position which need modified would turn yellow.
"Close the voice", Yellow "Open the voice" Pic 4.7 voice setting up interface The cursor position is blue inverse. Pic 4.8 time set up interface Call Space (send interval) ，Call Power ，these all could modify through the direction key.
Pic 4.10 is the testing interface In this interface, the green menu is the work mode choosing position. Current mode is TakeMeal. To modify the mode, according to the > guide, press the right key, it would turn to the other waitmeal mode. The indicator before the waitmeal mode turn into < , it means you could switch to take meal mode through left key. Pic 4.11 working Mode Remark：Working mode setting is valid only operate before there's no any swipe card operation. Pic 4.
4.1.5 Single key paging interface Pic 4.13 Single key paging interface Single key paging interface is shortcut manner. To page directly through one key, the one key page list is downloaded in the equipment in advance, these information are edited by the operator. In this interface, could page turn to check the paging Number and Paging content through pg up and pg dn. Through F3 key to enter or exit operation. 4.2 Coaster Pager Operation Instruction 4.2.
Pic 4.14 Download Parameter Position Remark：pls make sure the coaster pager in wake status before download. If it isn't in the wake status, pls swaying the coaster pager to light the Nixie tube to be in the working status. 4.2.2 Queue There's a induction card area in the coaster pager upper cover.
2、Check whether there's battery in the coaster pager. 3、Charge the coaster pager to full. 4、Power on the transmitter. 5、Transmitter parameter setting. There's memory function in the transmitter setup part. It would remember the last time saved setting information.Unnecessary to set it up each time, if any modification, pls enter into the set up interface to modify. 6、Enter the coaster pager data into the transmitter, and download it into the transmitter through the data wire. 5.1.
tube. Remark：This function only valid when the queue number within 9. 3、Out of the range warning 5.1.4 Delete the wait meal information When the customer take back the paging coaster pager, firstly to delete the number in the transmitter then put the pager onto the charger. At this time the pager would stop paging and enter into the charging. 5.2 Staff Paging 1、in the customer paging interface, press"F1" enter into the staff paging interface.
If the BP is a digit， it would send the corresponding code. Otherwise, you could press the ENT ,the message would be chosen, it is editable. 5.3 other special function 1、If the staff want to delete the unuseful message, follow the following process： （1）Chosen the message would to be deleted （2）Press“*”key，a tip box would be bounced up （3）press ENT to delete，otherwise press ESC 6 Breakdown & Solution 1、When Swiping there's warning tone but there's no queue message in the screen.
transmitter then press “F1+F2”key，Then restart up，after the prompt letter then release F1、F2，then start up again. 4、Transmitter paging lose message Reason：During paging, check the paging icon position, which would display the queue number. The treatment Max number is 40pcs. The data over 40 would be discarded. 5、The transmitter sending message too slowly Reason：Pay attention to the sending time interval and the heart beat data setting.
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. FCC Part 15.
