Walkie Talkie M-900 US User Guide
CAUTION Read this operating instruction carefully before using your two way radio, including the part on Product Safety and Important Notice. 1 2 11 3 10 4 9 5 8 6 12 13 14 15 7 12. Wrist Strap Connection 1 . Antenna 13. Belt Clip 2. Backlit LCD Display 14. Battery Compartment 3. NOAA/Scan Button 15. Battery Door Latch 4. Down Button 5. Menu/Power Button 6. Microphone 7. External Speaker/ Microphone/Charge Jack 8. Speaker 9.Up Button 10.Call/Lock Button 11.
Product Features Features • 22 Channels Backlit LCD Display 2 3 4 5 1 • 10 Channel NOAA All 6 Hazards Radio 9 • Weather Alert 8 • 121 Privacy Codes (38 CTCSS codes/83 DCS codes) 13 7 12 • Hands-Free Operation (VOX) • Scan Channels,privacy codes • Backlit LCD Display • Call Alert Ten selectable tones • Button Lock • Speaker/Microphone/ Jack/Charge Jack 11 14 10 1. Battery Level Indicator 2. VOX Icon 3. Scan Icon 4. Roger Beep Icon 5. Lock Icon 6. Low Power Icon 7. DCS/CTCSS Icons 8.
Product Features Channel Frequency(MHz) Channel Frequency(MHz) 1 462.5625 12 467.6625 2 462.5875 13 467.6875 3 462.6125 14 467.7125 4 462.6375 15 462.5500 5 462.6625 16 462.5750 6 462.6875 17 462.6000 7 462.7125 18 462.6250 8 467.5625 19 462.6500 9 467.5875 20 462.6750 10 467.6125 21 462.7000 11 467.6375 22 462.7250 Installing Batteries To install or replace batteries: 1. Remove the belt clip by pulling the tab and sliding it up. 2. Pull the battery door lock tab up to release the battery cover.
Quick Start 1. Press and hold the Menu/Power button to turn on your radio. 2. Press the Menu, Press the Up or Down button to select a channel. Both radios must be tuned to the same channel/privacy code to communicate. 3. Press and hold the PTT button while speaking into the microphone. 4. When finished talking, release the PTT button and listen for a response. Turning on Your Radio Press and hold the Menu/Power button until you hear a series of audible tones indicating the radio is on.
Auto Battery Save If there are no transmissions within 3 seconds,the radio will automatically switch to Battery Save mode and the Power Saver icon will displayed. This will not affect the radio’s ability to receive incoming transmissions. Communicating with Another Person 1. Press and hold the PTT button. 2. With the microphone about two inches (2.5-5 cm) from your mouth, speak in a normal voice. 3. Release the PTT button when you are finished talking and listen for a response.
Call Button Press and release the Call button. The other person will hear a two second call tone. This tone is used only to establish voice communications.See page 8 on how to select between ten call tone settings. Lock Function The Lock function locks the Up, Down, Scan and Menu/Power buttons to prevent accidental operation. To turn the lock on or off: –Press and hold the Call/Lock button for two seconds. Lock Icon A double beep sound is used to confirm your lock on or off request.
To successfully communicate using a privacy code, both the sending and receiving radios must be tuned to the same channel and to the same privacy code system (CTCSS or DCS) and privacy code number. Each channel will remember the last privacy code system and number you select. The privacy code 00 is not a privacy code, but allows all signals to be heard on a channel that is set to 00 on both the CTCSS and DCS systems. Set CTCSS Privacy Codes To select a CTCSS privacy code: 1.
Voice Activated Transmit (VOX) In VOX mode, your radio can be used “hands-free,” automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise. To turn VOX mode on/off: 1. Press the Menu/Power button until the VOX icon on the display. 2. Press the Up or Down button to turn VOX On. The current " 0N” setting is displayed. VOX Icon 3. Press the Up or Down button to turn VOX Off.
Roger Beep Confirmation Tone Your listener will hear an audible tone when you release the PTT button.This alerts the other party that you are finished talking and it is OK for them to speak. To turn roger beep on or off: 1. Press the Menu/Power button until the Roger Beep icon is displayed . The current on or off setting flashes . 2. Press the Up or Down button to select roger Roger Beep On beep on or off. 3. Choose one of the following: a.
Channel Scan Your radio can automatically scan channels. To scan channels: 1. Press and release the Scan button until the Scan icon and the channel numbers appear on the display. 2. Press and hold the Scan button to begin scanning channels. The radio ignores specific privacy codes while scanning channels. The Scan icon will continue to be displayed when scan is on. Your radio will continue to scan all channels and stop if an incoming transmission is detected.
a. Press and hold the PTT button to communicate on that channel/ privacy code. Your radio will remain on that channel/privacy code and return to Standby mode. b. Press the Up or Down button to resume scanning privacy codes. If you do not press any button within 10 seconds, your radio will automatically resume scanning privacy codes. Scan Privacy Codes Select Channel NOAA* All Hazards Radio Channels • You can use your radio to listen to NOAA All Hazards Radio channels transmitting in your area.
To turn Weather Alert On or Off: 1. Press the Menu/Power button until the Weather Alert icon flashes on the display in the NOAA mode. The current On or Off setting is displayed. 2. Press the Up and Down button to turn Weather Alert On or Off. 3. Press and hold the Menu/Power button again to save the new setting and exit the Weather Alert Mode and return to Standby mode. This radio is rain resistant to JIS4 standards. Transmit and Receive Procedure Your two-way radio contains a transmitter and a receiver.
FCC Statement This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
