Walkie Talkie User Guide US
CAUTION 1 Read this operating instruction carefully before using your two way radio, including the part on Product Safety and Important Notice. 12 13 2 14 3 11 4 10 9 5 15 6 7 8 1 . Antenna 2. Backlit LCD Display 3. Menu/Power Button 4. Call/Lock Button 5. Up Button 6. Microphone 7. Speaker 8. External Speaker/ Microphone/Charge Jack 16 9. Down Button 10.Scan/Lamp Button 11. PTT(Pull to talk) Button 12. Lamp 13. Wrist Strap Connection 14. Belt Clip 15. Battery Compartment 16.
Product Features Channel Frequency(MHz) Channel Frequency(MHz) 1 462.5625 12 467.6625 2 462.5875 13 467.6875 3 462.6125 14 467.7125 4 462.6375 15 462.5500 5 462.6625 16 462.5750 6 462.6875 17 462.6000 7 462.7125 18 462.6250 8 467.5625 19 462.6500 9 467.5875 20 462.6750 10 467.6125 21 462.7000 11 467.6375 22 462.7250 Installing Batteries To install or replace batteries: 1. Remove the belt clip by pulling the tab and sliding it up. 2. Pull the battery door lock tab up to release the battery cover.
Product Features Features • 22 Channels • 121 Privacy Codes (38 CTCSS codes/83 DCS codes) Backlit LCD Display 2 3 4 5 1 6 • Hands-Free Operation (VOX) 7 • Scan Channels,privacy codes 12 11 • Backlit LCD Display • Call Alert Ten selectable tones • Button Lock • Speaker/Microphone/ Jack/Charge Jack • Roger Beep Selectable On/Off • Battery/Power Saver • Keystroke Tones • Battery Level Indicator • Low Battery Audible Alert • Auto Squelch • Belt Clip 10 9 8 1. 2. 3. 4. 5. 6. 7. 8.
Quick Start 1. Press and hold the Menu/Power button to turn on your radio. 2. Press the Menu, Press the Up or Down button to select a channel. Both radios must be tuned to the same channel/privacy code to communicate. 3. Press and hold the PTT button while speaking into the microphone. 4. When finished talking, release the PTT button and listen for a response. Turning on Your Radio Press and hold the Menu/Power button until you hear a series of audible tones indicating the radio is on.
Auto Battery Save If there are no transmissions within 3 seconds,the radio will automatically switch to Battery Save mode and the Power Saver icon will displayed. This will not affect the radio’s ability to receive incoming transmissions. Communicating with Another Person 1. Press and hold the PTT button. 2. With the microphone about two inches (2.5-5 cm) from your mouth, speak in a normal voice. 3. Release the PTT button when you are finished talking and listen for a response.
Call Button Press and release the Call button. The other person will hear a two second call tone. This tone is used only to establish voice communications.See page 8 on how to select between ten call tone settings. Lock Function The Lock function locks the Channel Up, Channel Down and Menu/Power buttons to prevent accidental operation. To turn the lock on or off: –Press and hold the Call/Lock button for two Lock Icon seconds. A double beep sound is used to confirm your lock on or off request.
To successfully communicate using a privacy code, both the sending and receiving radios must be tuned to the same channel and to the same privacy code system (CTCSS or DCS) and privacy code number. Each channel will remember the last privacy code system and number you select. The privacy code 00 is not a privacy code, but allows all signals to be heard on a channel that is set to 00 on both the CTCSS and DCS systems. Set CTCSS Privacy Codes To select a CTCSS privacy code: 1.
Voice Activated Transmit (VOX) In VOX mode, your radio can be used “hands-free,” automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise. The current VOX sensitivity level is displayed with letters “ vox ” and a Number 1 through 3, with Number 3 being the most sensitive level and Number 1 being the least sensitive level. 2. Press the Up or Down button to change the setting. 3.
Roger Beep Confirmation Tone Your listener will hear an audible tone when you release the PTT button.This alerts the other party that you are finished talking and it is OK for them to speak. To turn roger beep on or off: 1. Press the Menu/Power button until the Roger Beep icon is displayed . The current on or off setting flashes . 2. Press the Up or Down button to select roger Roger Beep On beep on or off. 3. Choose one of the following: a.
Channel Scan Your radio can automatically scan channels. To scan channels: 1. Press and release the Scan button until the Scan icon and the channel numbers appear on the display. 2. Press and hold the Scan button to begin scanning channels. The radio ignores specific privacy codes while scanning channels. The Scan icon will continue to be displayed when scan is on. Your radio will continue to scan all channels and stop if an incoming transmission is detected.
a. Press and hold the PTT button to communicate on that channel/ privacy code. Your radio will remain on that channel/privacy code and return to Standby mode. b. Press the Up or Down button to resume scanning privacy codes. If you do not press any button within 10 seconds, your radio will automatically resume scanning privacy codes. Select Channel Scan Privacy Codes Safety Information for Radios Your wireless handheld portable transceiver contains a low power transmitter.
FCC Statement This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.