Walkie Talkie User Guide US
CAUTION Read this operating instruction carefully before using your two way radio, including the part on Product Safety and Important Notice. 1 2 3 12 11 4 10 5 13 9 8 7 1 . Antenna 2. External Speaker/ Microphone 3. Backlit LCD Display 4. Call/Monitor Button 5. Up Button 6. Microphone 7. Speaker 14 6 15 8. Down Button 9. Menu/Lock Buttonn 10.Power /Scan Button 11.PTT(Pull to talk) Button 12.Wrist Strap Connection 13. Belt Clip 14. Battery Compartment 15.
Product Features Features • 22 Channels Backlit LCD Display 2 • 121 Privacy Codes (38 CTCSS codes/83 DCS codes) 3 4 5 1 • Hands-Free Operation (VOX) 6 • Scan Channels • Backlit LCD Display 9 • Call Alert 8 Ten selectable tones • Button Lock • Speaker/Microphone/ Jack • Roger Beep Selectable On/Off 1. 2. 3. 4. 5. 6. 7. 8. 9.
Product Features Channel Frequency(MHz) Channel Frequency(MHz) 1 462.5625 12 467.6625 2 462.5875 13 467.6875 3 462.6125 14 467.7125 4 462.6375 15 462.5500 5 462.6625 16 462.5750 6 462.6875 17 462.6000 7 462.7125 18 462.6250 8 467.5625 19 462.6500 9 467.5875 20 462.6750 10 467.6125 21 462.7000 11 467.6375 22 462.7250 Installing Batteries To install or replace batteries: 1. Remove the belt clip by pulling the tab and sliding it up. 2. Pull the battery door lock tab up to release the battery cover.
Quick Start 1. Press and hold the Power/ S can button to turn on your radio. 2. Press the Menu, Press the Up or Down button to select a channel. Both radios must be tuned to the same channel/privacy code to communicate. 3. Press and hold the PTT button while speaking into the microphone. 4. When finished talking, release the PTT button and listen for a response. Turning on Your Radio Press and hold the Power/Scan button until you hear a series of audible tones indicating the radio is on.
Communicating with Another Person 1. Press and hold the PTT button. 2. With the microphone about two inches (2.5-5 cm) from your mouth, speak in a normal voice. 3. Release the PTT button when you are finished talking and listen for a response.You cannot receive incoming calls while pressing the PTT button.Both radios must be tuned to the same channel/privacy code to communicate. To Select a Channel With the radio on, select any of the 22 channels by pressing M enu and the Up or Down button.
Lock Function Lock Icon The Lock function locks the Up, Down and Menu buttons to prevent accidental operation. To turn the lock on or off: – Press and hold the Menu/Lock button for three seconds. A double beep sound is used to confirm your lock on or off request. When in Lock mode,the Lock icon will be displayed. Scrolling Through the Menu Function By scrolling through the MENU function, you will be able to select or turn on preferred features of your radio.
Set CTCSS/DCS Privacy Codes Privacy Code To select a CTCSS/DCS privacy code: 1. After selecting a channel, press the Menu/Lock button until the small numbers next to the channel number flash on the display. 2. Press using the Up or Down button to select a privacy code. You can hold the Up or Down button for fast advance. 3. When your desired CTCSS/DCS privacy code is displayed (CTCSS:01 through 38,DCS:39 through 121) , choose one of the following: a.
VOX Icon The current VOX sensitivity level is displayed with letters “ ” and a Number 1 through 3, with Number 3 being the most sensitive level and Number 1 being the least sensitive level. 2. Press the Up or Down button to change the setting. 3. Choose one of the following: a. Press the Menu/Lock button to enter the new setting and proceed to other functions. b. Press PTT button to enter the new setting and return to Standby mode. To turn VOX mode off: 1.
Setting the TX POWER LOW/HI 1. Press the Menu/Lock button seven times until pr displays. 2. Press the UP or DOWN button to select the Lo or HI level. 3. Press the PTT button to save the TX POWER LOW/HI setting. Roger Beep Confirmation Tone Your listener will hear an audible tone when you release the PTT button.This alerts the other party that you are finished talking and it is OK for them to speak. To turn roger beep off: 1. Press and hold the Power button turn the radio off. 2.
radio will continue to scan all channels and stop if an incoming transmission is detected . Your radio will remain on that channel for 10 seconds . During scanning (while receiving an incoming transmission), you can choose from the following: a. Press and hold the PTT button to communicate on that channel . Your radio will remain on that channel and return to Standby mode . b. Press the Up or Down button to resume scanning channels . c. Press and hold the Scan button to return to Standby .