UWB-03S User Guide UWB-03S User Guide 1. Functional description The UWB ceiling type anchor acts as a bridge between the tag and indoor positioning system. The precision positioning system transmits positioning data to the server via wire or wireless network. The UWB anchor has two kinds of design : embedded with wire network (RJ45) or wireless (2.4G WiFi) network for different environmental conditions. UWB ceiling type anchor (Model : UWB-03S) UWB Operational range: max.
Modules User Guide RJ45 Working mode : AP mode/ station mode Network protocol : PPPoE/ DHCP customer mode /DHCP Server Safety strategy : supporting 64/128 bit WEB encryption, WPA-PSK encryption, WPA2-PSK encryption Configuration management : Web user management entity (remote management/ local management), support SNMP, support TFTP/HTTP software upgrade WiFi Starting time requires 1 second Serial command : AT + ping Interface mode : UART/SPI/GPIO Interface speed : 1200~460800 bps Support SmartConfig– conf
UWB-03S User Guide 2.
Modules User Guide 3. Model specifications 1. UWB Ceiling Anchor （Standard） 1.Operational range : max. 100m ( 30~50m recommended ) 2.Communication interface : UWB/RJ45 /WiFi 3.Communication protocol : 802.15.4a UWB 4.Frequency : 3.25GHz~6.75GHz 5. Working method : TOF 6.Antenna angle : 360 degree 7.Installation : ceiling type 8.Input voltage : DC5V/PoE 9.Dimensions (W x Dx H) : 110×110×33 mm(outside) 10.
UWB-03S User Guide 4. Specifications (UWB) Items Detail Model Name UWB-03S Processor DW 1000+STM32 Flash Communication range Up to 100 m (max.) Communication interface UWB / RJ45 / WiFi Frequency UWB : 3.25~6.75GHz / WiFi : 2.412~2.484 GHz ＊.Transmitting mode < 50mA Power consumption ＊.Receiving mode < 50mA ＊.standby mode < 50mA ＊.Operating temperature -25~+75℃ Environment ＊.Storage temperature -40~+80℃ ＊.Operating Humidity max.
Modules User Guide 5. Specifications (WiFi) Items Detail Wireless standard IEEE802.11b/g 802.11n forcast Frequency 2.412~2.484 GHz 802.11b: -90 dBm @ 11Mbps Sensitivity （typical） 802.11g: -70 dBm @ 54Mbps （typical） Wireless 802.11b: 1,2,5.5,11 Mbps Data rate 802.11g: 6,9,12,18,24,36,48,54 Mbps Modulation system Output power Hardware 802.11b: 17±2 dBm（typical） 802.11g: 15±1 dBm（typical） IPX/micro strip Interface type UART/SPI interface speed 1200~460800 bps Working voltage 3.3±0.
UWB-03S User Guide Safety regime WEP/WPA-PSK/WPA2-PSK Encryption WEP64/WEP128/TKIP/CCMP(AES) Support 4 STA connection Support communication between STA and AP, but not support AP paradigm communication between STA and STA Encryption to support OPEN and WEP Working paradigm Auto/command Serial command AT+ping max. number of connection：8 max. number of client：8 TCP max. number of server：3~4 Local server that connects max. number of client：4 UDP Highest transmission rate max.
Modules User Guide 6. Installation UWB-03Smoduleusesasuctioncupinstaller.Withthedifferenttypeof installer,theinstallationprocessisdifferenttoo.Hereisademonstrationof howtomountasuctiontypemodule. 1. Installation instructions * This instruction is for reference only. 1.
UWB-03S User Guide Bracket slot Back View A removable bracket plate is included for the wall mounting system as shown 1-9
Modules User Guide Bracket hook Mounting Hole Dimensions： Front View 1-10 Side View
UWB-03S User Guide 2. Accessories included ： KA3X12 screw x 3 Make sure the screw head diameter does not exceed more than 8mm.
Modules User Guide 3. Drill 3 holes in the wall, each aperture is measured at 5mm and make sure the drilled holes are aligned to the mounting holes on the bracket plate. 4. Begin with the M6, insert it into the drilled holes.
UWB-03S User Guide 5. Align the mounting holes to the bracket plate. 6. Screw in the KA3X12 into each hole.
Modules User Guide 7. Installation complete: 8. Once the bracket had been mounted onto the wall, attach UWB-03S onto the bracket and rotate clockwise to secure and lock its position.
FCC Statement 15.19 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 15.21 Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
