深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 遥控器产品规格书 Remote control Specification 文件编号: 产品名称 Product name RF439A IR/BLE Voice Remote Control C&D 产品型号 Part NO 135439A0001 客户型号 Funai Part No URMT26CND001 生产厂家 Production factory Shenzhen C&D Electronics Co., Ltd.
If any matter related to these specifications needs to be clarified, discussions shall be hold promptly the two parties concerned the to determine the issue. 如规格书中的任何内容需要解释,需双方讨论定夺. 版本记录 Version: 版本 Version 日期 Date 姓名 Name V1.0 2021-2-2 Yanling Fu V1.1 2021-3-22 Yanling Fu 备注 Notes Draft 2、目录 Index NO.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 三、检验内容及要求 1、 (Verification content & Requirement) 一般项目(General Items) 1.1、 适用范围 Apply for: RF439A Remote Control 1.2、 工作环境 Working Environment: 0℃~45℃、5﹪~80﹪RH 1.3、 存储温度 Storage Environment:-20℃~60℃,5﹪~90﹪RH 1.4、 试验环境 Test Environment:5℃~35℃、45﹪~75﹪RH、86~106Kpa 1.5、 额定电压 Rating Voltage:DC3.0V 1.6、 适用电池 Battery: R03/AAA x2pcs 1.7、 重量范围 Weight:77g(Without battery) 1.8、 产品尺寸:165.30*48.00*20.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 3、 电气性能 Electric Capability 序号 项目 测试要求 Test Requirements 3.0 主控芯片 IC Airoha AB1613 3.1 软件版本 FW Version RF439A-V06 3.2 蓝牙版本 Bluetooth version Bluetooth LE 4.2 3.3 按键数量 Number of Keys 26 Keys (including Mic. Key) 3.4 遥控器设备名称 Remote control device name Philips TV Voice RC_6 3.5 载波频率 Carrier frequency 2402MHz ~ 2480MHz 跳频 3.6 工作电压 Working Voltage 2.0v ~3.3v ≤10uA 在 3.0V 电压下,配对后的遥控器静置 30 秒后(进入深度睡眠状态) 3.7 待机电流 Static Current 后测量其电流.At 3.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. Google ATV Voice On-air data rate: 64kbps [16kHz/16bit/4:1 ADPCM Compression]and 3.13 语音采样率 Audio feature 32kbps [8kHz/16bit/4:1 ADPCM Compression] Press & Release Talk Voice timeout: 30sec Evaluate the SNR of Voice data(wav.) that be captured 评估所评估语音的信噪比如下: 3.14 语音信噪比 Audio SNR [Google ATV Help] THD MUST be less than 5% @1kHz, (94dB SPL as referenceAudio input sensitivity: 94dB SPL as refrence sound pressure level). - 3.15 低电压提示 Battery Level 3.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. Target 36 months -Idle 理想的状态是 36 个月 ● Calculate based on quiescent current Target 12 months -Active 基于静止与工作电流计算,目前是 12 个月 ● Calculate based on daily key presses and BLE voice usage 基于日常按键使用和语音使用计算 Battery life test 3.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. remote control has changed and whether the 0.1ml,面积约 1cm²,然后软布擦干。Drop the 60℃ characters and marks have been erased. warm water on the surface of the remote control in three different parts (including character and graphic symbol parts) with the dropper. Drop 0.1ml on each part, with an area of about 1cm, and then wipe the soft cloth dry. Alcohol tolerant test 99% methanol with 4.9N load ->Printing SHOULD not fade .丝印要求不掉色. 耐酒精测试 99%甲醇,4.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. Cross cut test 百格测试 4.9 Should cut lines (11×11) at intervals of 1mm with ->a square SHOULD not cling to the tape. cutting knife, 胶带上不能粘碎屑 用刀每隔 1mm 割一条线(11X11) measure force of adhesion, count number of Paste the scotch tape on cutting area and peel it pealed section in cutting area. off quickly at an angle of 45° 测量附着力,计数切割区域内已剥落的截面数。 在被割的区域贴上透明胶带并且在 45°角快速撕 下胶带. Waterproofing test Pour water 200ml on the keys, specially the gap 1.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. wet or mark of liquid infiltration shall be observed on the PCB (circuit patterns side). 7. 打开上壳观察内部。在电路的那一面,不能有 水渍如板子的痕迹. 4.11 盐 水 测 试 Salt water test 检查遥控器的外观是否异常.字符标志应清晰可 用浸过 20%食盐水的棉球或软布,轻轻擦拭遥控器 见。Check the appearance of the remote 表面(包括按键字符部位)50 次。Gently wipe the control surface of the remote control (including for abnormalities. Character markings should be clearly visible.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 4.16 4.17 按键工作寿命 Key ->All functions SHOULD operate normally. Press working life test. No harmful defects to appearance and structure 200,000times. 所有的功能要正常,表面和结构没有严重的损坏 用规定的荷重按压按键 20W 次。 After performing the lid opening / closing cycle, Attach and detach the battery cover 200times.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. Drop test (Abnormal height) 跌落测试(非正 4.22 常高度) Drop the RCU onto concrete- or asphalt- floor 不可以有遥控器结构破损,遥控器零件散落等连接 from 150cm height, about the weakest planes of 性的问题发生 RCU in the Normal height Drop test And the edges of broken cabinet should not be 将遥控器最弱那面从 150cm 高度跌下,跌在混凝 sharp. 土或者沥青地面上 accepted. ->SHOULD be free from abnormality such as 断裂的结构件边缘不能是锋利的。 scattering of broken cabinet etc.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 共 6 小时) *测试后,在室温中放置 30 分钟,然后检 查外观和电气性能. after testing, leave it at room temperature for 30 minutes, then check appearance and electrical properties. 4.26 包装运输试验:跌落 没有功能失效或材料损坏 No functional failure 将整箱产品从 60cm 高度跌落到地面,对其中三 试验 Packing and or material damage 个轴向,1 边和 1 个角进行试验. FCL products transportation were dropped from a height of 60cm to the test: drop test ground, and three axial directions, one side and one Angle were tested. Key 4.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. *Discharge with the battery removed 不带电池测试 >If the RCU recovers by reinsertion of the battery, it is DESTRUCTION. 如果遥控器从新装上电池后才回复,这就是损毁。 >If the pairing memory is erased, it is DESTRUCTION. 如果配对信息擦除,这就是损毁。 >If RCU reconnects automatically after disconnecting with the TV, it is MALFUNTION. 如果遥控器于电视机断连后又从新自动回连,这是 故障 5、环境测试 Environmental Test 序号 No. 项目 Item 测试要求 Test Requirements 遥控器在装电池,不包装的状态下,放入具有室温的试验箱内,试验箱内的温度以 1±0.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. reaches the stable laboratory environment temperature, take out the remote controller and check whether the functions of the remote controller are normal. 遥控器在不包装不装电池的状态下,放入具有室温的试验箱内,然后将箱温调节至 40±2℃,当遥控器达 到温度稳定后再加湿度在相对湿度为 93%,搁置 96H,先把试验箱内的相对湿度在 0.5h 内降低到 75%±3%,然后在 0.5H 内把试验箱内的温度调到正常试验大气条件下,取出遥控器 。遥控器恢复 4H 后,检查遥控器的各项功能是否正常.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 分功能、灵敏度) 测试完成后行为模式正常,无误触,反应慢。The rising temperature is 45 degrees above zero,60% humidity (keep the temperature for 3 hours or so and check the function of the remote control, feel of the keys and the function and sensitivity of the touch control part), the behavior mode is normal after the test is completed, without accidental trigger or slow reaction. Conduct the heat shock(-20℃⇔+60℃) cycle 100+/-5cycle. Measure perfprmance after leaving Thermal 5.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 五、按键码值 Code Table Peak Wavelength TYP 940nm Format RC6 format: In addition to specification of “RC6 mode 0”, Carrier Frequency 36kHz ±0.36kHz Duty 33% [Mic. Key] Paired : send key-code by BLE the followings should also be satisfied. Unpaired : send key-code by IR [the other Keys] send key-code by IR Philips RCU Code Table Position Front No.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. -Unpairing from the Host clears bonding cache -Operating Unpairing key function clears bonding cache 5.Voice search [Start] - Push [Google Assistant ] key [LED behavior] 6.Bug Report - LED turns on after ACK from host when voice search is ready - LED turns off after end of speech is detected from the host, or - LED turns off after 30 seconds of time out [Start] - Output the key code during pressing and holding [OK] and [BACK] [Code sending] 7.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD.
深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. IC WARNING: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.