User’s Manual Bluetooth Speaker BTS11 1
A. Important Don’ts • Do not place naked flames, such as lighted candles on or near the product. • Do not place objects filled with liquids, such as vases on or near the product. • Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration. • Do not keep or store this product in wet conditions for long period. • Do not clean this product with water or other liquids. • Do not block or cover the slots and holes in the product.
B.
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Control Silicon Cover (for protect I/O port) Silicon Hanger (for lanyard) Speaker Bass Radiator Battery Indicators (LED x 4 for charge status or battery level) AUX Input (Under Silicon Cover) USB Micro Socket (Under Silicon Cover) USB Type-A Socket (Under Silicon Cover) Button (Power on and off) Button (Volume, Previous Song) MIC Hole (For Hand-free) Button (Volume, Next Song) Mode Indicator (blue for wireless, red for AUX) Toggle Button (for Power Bank Control)
- If the LED 4 blinking < 100%) - If all LEDs remain solid, the unit is fully charged. 6. Disconnect the USB cable when it is done. D. Use Power Bank Function (Output DC 5V 1A max.) Before use the power bank function, make sure that the Speaker’s internal battery is full charged. Or, we recommended, it has enough energy, about 51 ~ 75% or more, for charge the external device. a. To check the battery remaining energy level: 1.
Bluetooth devices, you may need to input “0000” as pairing password) 3. If pairing is successful, a beep sound will heard and the “Mode Indicator (13)” will slow blinking each 4 ~ 5 seconds once. 4. Now, you can start to music play from the mobile device by it music player program. c. Power Off: 1. Press and hold the “ (9)” button again to turn off the Speaker when it is not in use. 2. A series of tones will sound from speaker and the Speaker will turn off.
g. Wireless Music Playing Control Function: (on Speaker) 1. In playing music, press “ / (16)” button to pause the music. To resume the music press it again. 2. Press and hold the “ 12)” button to increases the volume level. 3. Press and hold the “ (10)” button to decreases the volume level. 4. When maximum or minimum volume is reached, a tone will sound. 5. Press once the “ (12)” button to go to next music. 6. Press once the “ (10)” button to go to previous music. h. Hand-Free Function 1.
2. The Speaker will switch to “AUX In” mode automatically from wireless, and the “Mode Indicator (13)” will switch to red from blinking blue. 3. Now the AUX In function is ready, start to music play from your external device by it control and or program, for example, Play, Stop, volume control…etc. 4. You also can use Speaker control; 5. Press and hold the “ (12)” button to increases the volume. 6. Press and hold the “ (10)” button to decreases the volume. 7.
I. Specification Dimension 63.2 mm (L) x 36.3 mm (W) x 132 mm (H) (not included lanyard holder) Weight 316g Specification BT V2.1 + EDR Wireless Supported Profile A2DP, AVRCP, HSP Connection Distance In 10 meters (open area) Lithium 3.7V, 4000mAh Built-In Battery Playing Time: 10 ~ 12 hours (at 75% of volume setting) Power Input USB Micro Port DC 5V 1A Output Power 3W (RMS) at 4 Ohm Freq.
Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.