User's Manual

ManualsBrandsShenzhen Belter Health Measurement and Analysis Technology ManualsElectronicsBluetooth wi-fi smart health scale

Koogeek-S1

Function

View 8 Groups of Body Composition Data via the app.

Weight: Check your weight trends

Lean Mass %: Track muscle gain

Fat Mass%: Measure body fat percentage, track fat loss

BMI: Check your healthy range

Bone Mass %: Check your bone mass percentage

Body Water %: Check your body water percentage

BMR: Check your basal metabolic rate

Visceral Fat %: Check your visceral fat percentage

Warning

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities of lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and any understand

the hazards involved. Children shall not be play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

This product will send the measurement data only after the completion of the human body

measurement

How to use

Summary of content (10 pages)

PAGE 1
Koogeek-S1 Function View 8 Groups of Body Composition Data via the app.
PAGE 2
1. Make sure the power supply is normal before using the smart health scale. 2. When a user stands barefoot on the smart health scale ( face the direction of smart health scale display with each foot stepping on the ITO film of the smart health scale), once the body weight is more than 5kg, the smart health scale will start measuring weight and body resistance and display weight on the screen. The smart health scale will automatically turn off five seconds after the user stepping off the scale. 3.
PAGE 3
PAGE 4
POWER Battery: 4xAA batteries SWITCH OFF OR AUTO OFF 1， After finish weighing or if no any operation of the scale, the scale will automatically switch off after approximate 30 seconds. LOW BATTERY INDICATOR When the battery power is low, scale will display "Lo", please replace the battery in time. ATTENTION 1， Place the scale on a hard and flat surface to ensure the greatest accuracy and reliability. 2， Do not use any chemical cleanser to clean the scale.
PAGE 5
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
PAGE 6
RF emissions 5 Class B The SF-371 body fat scale is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply netw ork that supplies buildings used for domestic purposes.
PAGE 7
Surge IEC 61000-4-5 ± 1 kV differential mode N/A ± 2 kV common mode < 5 % UT (>95 % dip in UT ) for 0.5 cycle Voltage dips, 40 % UT short (60 % dip in UT ) interruptions and for 5 cycles voltage variations on power supply 70 % UT input lines (30 % dip in UT ) for 25 cycles IEC 61000-4-11 N/A < 5 % UT (>95 % dip in UT ) for 5 sec Power frequency (50/60 Hz) magnetic field IEC 61000-4-8 NOTE 3 A/m 3 A/m Mains power quality should be that of a typical commercial or hospital environment.
PAGE 8
Guidance and manufacturer’s declaration – electromagnetic immunity – for EQUIPMENT and SYSTEM that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration – electromagnetic immunity The SF-371 body fat scale is intended for use in the electromagnetic environment specified below. The customer or the user of the SF-371 body fat scale should assure that it is used in such an environment.
PAGE 9
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
PAGE 10
/ 3.8 7.3 100 / 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations.