DD-806W
Contents Thank you for purchasing a Valor Multimedia unit. We hope you will find the instructions in this user manual clear and easy to follow. If you take a few minutes to look through it, you will learn how to use all the features of your new unit for your maximum enjoyment. After you have finished reading the instructions, please keep this manual in a safe place for future reference.
Auto Store (AS) ·······················································································21 Program Scan (PS) ··················································································21 DX and LOC Stations Signals······································································21 DVD Player Operation····················································································22 Insert/Eject Disc···············································································
Precautions To avoid the risk of injury or accident, read the following precautions before installing and operating the unit. On Safety Comply with your local traffic rules and regulations. While driving You must not watch or operate the monitor. It may distract you and cause an accident. Park your car in a safe place to watch and operate the unit. While operating Do not insert your fingers or foreign object into the unit’s loader while a CD/DVD is playing.
Preparations Please read all of the instructions below before beginning your installation. We recommend that you have your unit installed by an experienced car audio/navigation system installer. IMPORTANT NOTICE: It is very important that you read the WARNINGS and NOTES in this manual to ensure correct installation and use of your unit. Features 6.
NOTE: If the unit is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.
Controls and Indicators Button Operation Eject Press to eject disc. Reset Menu Press to enter MAIN menu, press again to return to previous source. Source Press to change the source. Power Off/VOL Press and hold to turn off the unit. Press once to power on when the unit is turned off. Short press while unit is on to mute the volume. Rotate to adjust the volume.
Key Areas for the Touch Screen The key areas are outlined below, for DVD, VCD playback mode and so forth. A — Return to MAIN MENU B — Select previous chapter C — Select next chapter D — Display the on-screen controls, and different mode displays different menu.
Remote Control Remote Control Functions Name Ref # Power Open Mute SRC Numeric button VOL up VOL down Information GOTO search 1 2 3 4 Stop/Band 10 Select ESC Menu Picture Repeat AB OK Direction buttons 11 12 13 14 15 16 Turn the power on/off Eject Disc Toggle on/off audio output Select source Directly access certain chapter / track / preset station in current band Increase the volume Decrease the volume Display playing information Position search function on VCD/DVD mode Select FM/AM band on Tuner
Title 18 Go back to title while playing DVD Root 19 Enter the main menu of the disc Turn on PBC while playing DVD Repeat 20 Repeat playback for current chapter Next 21 Previous 22 Fast Reverse 23 Fast reverse the disc content Fast Forward 24 Fast forward the disc content Audio 25 Change the audio language for disc playback Zoom 26 Zooming in/out on an image Angle 27 Play in different angle for a scene(if it is applicable) SUB Title 28 Language selection for subtitle Select the
TFT Monitor Operation Rear Camera Mode When the vehicle is placed in "Reverse", and a rear camera is connected to the unit, the monitor will automatically switch to the camera input source. Please make sure the reverse wire is connected. Screen Adjustment ―COLOR‖ ―CONTRAST‖ and ―BRIGHTNESS‖ can be adjusted. Screen Adjustment Procedure 1. Enter the Screen adjustment mode: Press the PIC button on the remote or go to main menu, then Set-up, then press Screen. 2.
Operation Instructions Power On / Off Press the POWER /VOL button to turn the unit on. You can also turn on the unit by pressing the button ( ) on the remote. Press and hold the POWER/VOL button on the front panel or press the POWER button ( ) on the remote to power off the unit. Source Selection Press the MENU Button on the front panel to change sources: TUNER, DISC, NAVI, CARD, FLASH DRIVE, BT-TEL, F-AUX, R-AUX, SETUP, and STANDBY. The source is displayed on the top left of the screen.
restores the settings before it was last powered off. Mute The volume can be mute by the following: ) on the remote to mute the volume from the unit. 1. Press the MUTE button ( 2. Press the /VOL knob on the panel. 3. Turning the /VOL knob counter-clockwise on the panel to volume to "0". NOTE: Press the MUTE button on the remote again to restore the volume. Adjusting the volume or using any of the audio set-up features will cancel the mute function. Standby 1.
Setup Menu Main Menu There are three methods to access the SOURCE menu. ·Press the MENU button on the front panel. ·Press the MENU button on the remote control. ·Touch the A area (Top left corner) on the touch-screen. Note: Touch screen must be used to select menu and adjust settings. The remote arrows cannot be used to select features on screen. The following instructions will show the different ways to access menus and settings. Screen Setting Press the SETUP icon on the main menu.
15
Time Setting Press the TIME icon while on the SETUP menu. Selecting a Setting for Adjustment Touch directly the options on the screen to select a setting to be adjusted.
DVD Setting Press the DVD icon while on the SETUP menu. Selecting a Setting for Adjustment Touch directly the options on the screen to select a setting to be adjusted. Parental Control To set the parental control the default password is 8888 you can then adjust your parental guidance. If a new set Password is used you must not forget the new set password, please write down on the manual. Once a new password is set you cannot use the default password or reset the password if forgotten.
System Setting Press the SYSTEM icon while on the SETUP menu. Selecting a Setting for Adjustment Touch directly the options on the screen to select a setting to be adjusted. Steering Wheel Control Setting Press YES to enter Steering Wheel Control setting. 1. If there is only one steering wheel control wire connected to the unit, select Mode One. If there are two steering wheel control wires connected to the unit, select Mode Two. 2. Press a function icon in the list. 3.
Basic Settings Press the BASIC icon while on the SETUP menu. Selecting a Setting for Adjustment Touch directly the options on the screen to select a setting to be adjusted.
Other Settings Press the OTHER icon while on the SETUP menu. Selecting a Setting for Adjustment Touch directly the options on the screen to select a setting to be adjusted.
21
Tuner (AM/FM) Operation Tuner Display : Press to change between FM and AM. : Press to seek down. Touch and hold for 3 seconds to scan the previous station. : Press to seek up. Touch and hold for 3 seconds to scan the next station. : Press to scan and store all stations in current band automatically. : Press to scan the stations in the 12 preset channels in the current band.
Using Preset Stations 12 preset buttons are used to save your favorite stations for each band. First 6 saved stations (P1-P6) for the current band appear on the screen. You can touch the arrow buttons or on the screen to see the other 6 stations. Saving a Station 1. Select a band (AM/FM), and then select a station. 2. Press and hold a present (P1-P40) on the right side of the screen for three seconds. The station will then be saved on the selected preset number. Select a Station 1.
DVD Player Operation NOTE: When properly installed, DVD video cannot be displayed on the main screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is in motion, the screen will display ―caution‖ with a blue background. Rear video output, (if used) will operate normally. Insert/Eject Disc Inserting a Disc When inserting a DVD disc, DVD mode will be enabled and disc will begin to play.
: Press to return to DVD main menu : Press to select Title, Chapter, and Time. : Press to enter EQ setup. Controlling Playback Stop Playback Press the stop button on the screen or press the ( the DVD playback; press the play/pause button remote control to resume play. ) button on the remote control to stop on the screen or the (OK) button on the Pause Playback Press the play/pause button on the screen to pause or to resume play. Accessing the DVD Menu 1. 2. 3. 4.
VCD Track Search Time – Go to specific time in the current track Track – Go to specific track Disk Search Time __:__:__ Track VCD Disc Search Time – Go to specific time on disc Track – Go to specific track --- / --- 3. Enter a Time/Track number into the field using the numeric keypad on the remote control or on the screen. 4. Press the OK button on the remote control or on the touch screen to go to the specified location on the disc. 5.
between Left Channel, Right Channel, and Stereo. Changing Subtitle Language If you are watching a disc that contains multiple languages subtitles, press the (SUBT) button on the remote control to choose the language in which you would like the subtitles to appear. You also can touch area E, and then press the button.
: Indicates the Current source playing. : Indicates the playback time of the current title. : Indicates the tracks on the VCD and current track that is currently playing.
CD/MP3/WMA/JPEG Operation Instructions for Insert/Eject, Play/Pause, Stop Playback, Track Selection, Fast Forward/Fast Reverse, Scan, and Random Play are the same for DVD, CD and MP3 operation. Please see the DVD Player Operation section for information about these topics.
MP3/WMA Discs This player allows you to playback MP3/WMA files recorded on CD-R, CD-RW, DVD+R/RW and DVD-R/RW. For CD-RW discs, please make sure to use a slow speed write and not the fastest speed in order to prevent improper disc writing. When recording MP3s up to the maximum disc capacity, disable additional writing. Please use the "Disc at once" setting. The touch keys for CD/MP3/WMA playback are described below.
FLASH DRIVE Operation Accessing the Flash Source 1. To switch to FLASH source, press the Menu button on the front panel and press the Flash Drive icon or press the (SRC) button on the remote control until the FLASH appears at the top of the screen. NOTE: Make sure the USB cable is connected with a flash drive device. 2. Select the Main menu, and then touch the FLASH DRIVE icon to select FLASH as your source.
CARD Operation Accessing CARD Source 1. To switch to CARD source, press the Menu button on the front panel and press the CARD icon or press the (SRC) button on the remote control until the CARD appears at the top of the screen. NOTE: Make sure the SD card is inserted properly into the unit. 2. Select the Main menu, and then touch the CARD icon to select CARD as your source.
Bluetooth Operation Before using the Bluetooth Before using the Bluetooth, it is necessary to perform the following steps. 1. Go to the Main menu and select the ―SET UP‖ icon, select the ―BASIC icon‖ option and select ―Bluetooth‖, make sure the ―On‖ option is highlighted to activate the Bluetooth feature. 2. Pair your mobile phone to this unit (refer to the ―Pairing‖ operation). It is necessary to pair your phone first with the unit. If not paired the Bluetooth feature will not work.
A2DP Pairing Access the Bluetooth ―Setup” and select ―Pair Mode‖ to ―Yes‖, then select ―Phone‖ and a ―Waiting to pair‖ will be displayed on the screen. Now you can pair a phone with the unit. This unit can pair with 5 mobile phones in all, but only one can be active at a time. The Default phone will be retained only if all other paired phones are deleted. (Default Phone: The phone that was first paired with the unit.
enabled. Note: Please make sure your phone’s Bluetooth is on before turning on the unit. If your phone’s Bluetooth is turned on after the unit has been turned on you must pair the phone again in order to connect. Making a Phone Call There are three ways to make a phone call from this unit: 1. Use the phone’s number keypad to make a call. 2.
Troubleshooting Problem GENERAL Cause Corrective Action Radio Fuse blown Car battery fuse blown Unit will not power on Illegal operation Remote control does not function Battery depleted Battery installed incorrectly Improper audio output connection Volume set too low Improper ―MUTE‖ connection No/low audio output Poor sound quality or distortion Unit resets itself when engine is off Speakers damaged Heavily biased volume balance Speaker wiring is in contact with metal part of car Unauthorized disc
Image blurred, distorted, or dark PBC cannot be used during VCD playback No repeat or searching while playing VCD MP3 Interruption occurred during playback Incorrect playback message displayed Disc rating exceeds Parental Lock rating limit Disc region code is not compatible with unit Disc is inserted upside down Disc is illegally copied Change Parental Lock settings to allow such restriction Use disc with proper region code Insert disc with label side up Use original disc PCB is not available on the disc
Remote control Remote control does not function Battery is covered with insulation tape Battery depleted Battery installed incorrectly Pull out the insulation tape Replace battery with new one Remove battery and install correctly 1. When using the remote for the first time, you must pull out the insulation tape. 2. Remove the battery if the remote control is not used for a month or longer. If the battery is depleted remove and dispose of the old battery immediately.
Install the battery Insert the battery holder NOTE: Only use one CR2025(3V) lithium battery. Danger of an explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery. Do not recharge, disassemble, heat or dispose of the battery in fire. Keep batteries away from children to avoid the risk of accident. Suggestions 1. Only use a clean silicone cloth and neutral detergent to clean the front panel or monitor’s screen.
Specifications CEA Power Ratings Main Amplifier Power Output: 20 watts RMS X 4 channels into 4-ohms @ < 10% THD+N Signal to Noise Ratio: 70dB below reference. (Reference: 1 watt, 4-ohms) MAX Power: 25 X 4 watts into 4-ohms, all channels driven Frequency Response: 20Hz to 20kHz, -3dB. Aux input used as source reference Reference Supply Voltage: 14.4VDC DVD/CD Player Compatible formats: DVD-R, DVD-RW, DVD+R, DVD+RW, CD-R, CD-RW, CD-DA, HDCD, SVCD, VCD.
• 30 degrees up • 60 degrees down General Auxiliary Input impedance: 10k Power Supply: 10.5 to 16V DC, negative ground Fuse: 10-amp, mini ATM type DIN chassis dimensions: 7" X 7" X 2" (178mm x 178mm x100mm) * Specifications subject to change without notice.
Accessory List Description QTY Micro SD card 1 Frame 1 USB cable 1 Power harness 1 GPS antenna 1 Remote control 1 3.
Note: 1) Manufactured under license from Dolby Laboratories.Dolby and the double-D symbol are trademarks of Dolby Laboratories. 2) Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3) This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.