ETC62D-2.
Catalog 02 Function of Transmitter 03 Contents 04 Specifications 04 Notice for use 04 Notification before Using 05 Transmitter particular introductine 06 Menu introduction 07 Other function of the transmitter 11 Receiver 12 Electronic speed controler 10 Operation for transmitter and servo 13 The process of frequency bind for 2.4 GHz R/C system 15 Adjust order 14 Charge method of battery 16 Flow list 17 www.art-tech.
Thanks for purchasing ETC62D-2.4GHz radio control set. For safe use, please read this manual before using carefully. Any damage or loss to radio control set and model due to inproper use will not be shouldered by Art-Tech. Function of Transmitter ETC62D-2.4GHz is a newly developed 6 channel proportional transmitter. The latest developed product of ART-TECH RC Hobby Corporation. The 2.
Contents: Transmitter: ETC62D-2.4GHz Receiver: ER62-2.4GHz Simulator cable: 1pcs 1pcs 1pcs Belt: Manual: CD: 1pcs 1pcs 1pcs We do not offer servo, speed controller, battery or changer with the radio control system . Users can buy as spare parts. Servo: AS-100(9 g) Speed controller: ESC-30A 3pcs 1pcs Bettery packs: 9.6V/Ni-MH Charger: 1pcs 1pcs Specifications Number of channels: 6 Voltage Display: LCD Charging jack: yes Color: Black 3D switch: yes Antenna length: 15 cm Power supply: 12 V (1.
Notification before Using Indications of Special signs Please pay more attention to signs in this manual and safety while using Show Logo Meanings WARNING I improper operation may cause injury or hurt CAUTION I improper operation may cause injury or hurt Storage note ▲Please do not place the radio control set in the below situation: hot or cold（60℃above or -10℃below） under the sunshine long time moist condition dusty place vibration condition ▲long time without using, please pick up batteries from t
Transmitter particular introduce A B W C E F D G H I K M J L N P O Q R Y/UP LCD DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM MENU SUB ETC62-2.
Menu introduction After turn on the radio, the screen displays the time page. Press menu several times to enter the required main menu, Press the sub button during this period you can enter into the sub-menu of corresponding main menu. In the menu operation, the success of the button operation will accomplish with a prompt sound. If there is no prompt sound, maybe the button is not in place or this button has no function in this menu.
3. Popular options: 1. Press the menu button, enter into the Set menu. (There are 5 submenu included: D'R, Exp, Epa, Gyr, Mrv) 3.1 D'R (Dual Rate) settings: 1. Press the sub button; enter into the D'R menu (Dual Rate Settings). 2. Press the Left or right button, choose a channel (aileron, elevator or rudder), press the y / up or n / down button to increase or reduce the value. The values set take effect when the D'R switch is switched on.
(C mode) 1. Press the sub button to enter the Swash menu (Swash Rate Setting). The following Figure (1) is 120° CCPM and Figure (2) is 90° CCPM. Press y/up button or n/down button to choose to connect the aileron to CH1 or CH6, elevator to CH2, Pitch to CH6 or CH1. (1) 2. (2) Press the left button or right button to choose the right option (A for aileron, E for elevator, P for pitch).
0%),press the y / up or n / down button to increase or reduce the value. The values set take effect when the 3D switch is switched on. The value may be set anywhere between 0% and 100%) 5.mixing settings (A, V, D mode) Press the menu button, enter into the Mix menu (mixing).There are 2 sets of mixing settings. 5.1 Mixing setting: 1. Press the sub button; enter into the Mix1 menu (mixing 1). 2.
6.3 Auxiliary trim settings: 1. Press the sub button; enter into the Trm menu (Trim Settings). 2. Press the Left or right button, choose a channel. 6.4 Mode I and Mode II setting: 1. Press the sub button, enter into the Mode I and Mode II setting menu. Before Mode Setting, please unplug the power supply of the plane. Adjustment of joysticks The screws for mode setting are in the rear cover.
Receiver Specifications Operating voltage：4.8V~5.2V Current drain： ≤40mA Weight：12g dimension：44mm*23mm*15mm Channels: 6 Channels Range(Height)：≥350m Adjacent channel rejection：≥-85dBm± 16kHz Function For operating helicopter Operation for aeroplane CH CH RECEIVER ER61-2.4GHz RECEIVER ER61-2.4GHz B. Battery/Bind B. Battery/Bind 6. Pitch 5. Undercarriage 6. Pitch 5. Gyro gain 4. Rudder 4. Rudder 3. Throttle 3. Throttle 2. Elevator Signal + - 1. Aileron 2. Elevator Signal + - 1.
Operation for transmitter and servo For operating helicopter (Mode 1) Before adjusting, please be familiar with transmitter operation and servo(Below description in case of all neutral) Aileron Operation Joystick for ailoren left forward plane moves left Joystick for ailoren right forward plane moves right Elevator Operation Joystick for elevator up forward tail is up,and plane will go downforward Joystick for elevator down forward tail is down,and plane will go upforward Throttle Operation Joystick is
Operation for transmitter and servo Operation for aeroplane (Mode 1) Before adjusting, please be familiar with transmitter operation and servo(Below description in case of all neutral) Aileron Operation Joystick for ailoren righ forward the right ailoren up and left ailoren downand vice versa Elevator Operation Climb upforward Operation Joystick for elevator is down forward, the elevator is up,and tail is down, then the plane will climb up, and vice versa Operation for throttle Joystick for throttle is
The process of frequency bind for 2.4GHz R/C system (R eceiver with one antenna ) If oil aircraft, please connect the power of receiver to other channel at first, and then plug it to BATT after frequency bind. 1. Press the frequency bind button, then turn on the transmitter's power. 2. Connect the ESC to receiver for electricity supply, wihch results to the indicator light glitter. And then plug the short- circuit plug into the Receiver in the position of BATT. 3.
The process of frequency bind for 2.4GHz R/C system ( Receiver with two antenna ) If oil aircraft, please connect the power of receiver to other channel at first, and then plug it to BATT after frequency bind. 1. Plug the short-circuit plug into the Receiver in the position of BATT. Connect 2. Press the switch for frequency bind, then turn on the transmitter's power. the ESC to receiver for electricity supply, wihch results to the indicator light glitter. 3.
Adjust order Open the battery bay, and range the 8 cells AAA battery into the battery bay, then close the bay. 1. enter into the Chv menu, press the Left or right button, check whether the channels are in the right positions, at this time channel 1, 2 and 4 should be 0% ,the minimum value of channel 3 should be -100%, and the maximum should be 100%. If curve setting values are changed, it should be the set value. If the values are different Please adjust the channels mid points.
Flow list (1-9,A,b,C) (1-9,A,b,C) (CH1-6) Key 图示 (CH1,2,4) Menu Sub Left right y/up n/down (CH1,2,4) (CH1-6) (A , E , r) (A,V,D) (PT1-5) (H, C) (PT1-5) (PT1-5) (PT1-5) (A,V,D) (Mix 2,3,4 Set as Mix 1 ) (CH1-6) (CH1,2,4,6) 16 www.art-tech.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
