LCD DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM Opertating Manual
Catalog 02 Function of Transmitter 03 Contents 03 Specifications 03 Notice for flying 04 Notification before Using 05 Description of four flying modes 06 Transmitter particular introduce 07 Other function of transmitter 08 Receiver 09 Electrio speed controler 10 Operation for transmitter and servo 11 Adjustmen order 13 Charge method of battery 13 Explaination for Technical words 14 www.art-tech.
Thanks for purchasing E-Fly 100C radio control set. For safe use, please read this manual before using carefully. Any damage or loss to radio control set and model due to inproper usew ill n ot b e shouldered by Art-Tech. Function of Transmitter ETC61-2.4GHz is a new ly develo pe d 6 cha nnel propo rtinal transmiiter. The latest developed product of ART-TECH RC hobby corporation the 2.
Notice for flying Please do not fly in the rain or strong wind. The water can sink into the transmitter which can cause out of control,leading to crash. The shortened antenna may cause the short range. Pleas note before using, test the radio set first and any change to the radio set or model can cause crash. Please do not fly near housing, road,airport or power line 04 www.art-tech.
Notification before Using Indications of Special signs Please pay more attention to signs in this manual and safety while using Logo Show Meanings WARNING I Inproper operation may cause injury or hurt CAUTION I Inproper operation may cause injury or hurt Storage note ▲Please do not place the radio control set in the below situation: hot or cold（60℃above or -10℃below） under the sunshine long time moist condition dusty place vibration condition ▲long time without using, please pick up batteries from t
Description of four flying modes ETC61-2.4GHz with four flying mode installed:A(aeroplane mode); V(V tail mode);C (CCPM h elicopter m ode); H(helicopter mode) The swithc between each mode is very convenient. There is a reverse switch for Ch1, CH2,CH4 and CH6 separately.The LCD on the transmitter can show voltage o f transmitter, chann el status, flying mode and flying time.It has a function of auto-alarm for low voltage. A：Aeroplane 1.
Transmitter particular introduce A B C E G I K M O Q D F Y T U H J L N W P X V S R A：Antenna B：LCD(Liquid Crystal Display) 1）To indicate the battery voltage of transmitter 2）To show the situation of channels whether it is reversed 3）To show the flying time 4）To indicate flying mode 5）To indicate the status of lock and unlock C：Tiny Mix 1 D：Tiny Mix 2 E：Switch 1 This switch is for Ch5 tha t can b e use d fo r aeria l camera, collapsible landing gear and shift between gyro mode and gain, etc.
Other function of transmitter Alarm for low voltage of transmitter When the voltage of transmitter battery is under working voltage, the red LED will flash.It is better to stop flying,or that can cause crash of model. Switch for servo reverse operation During using, if servos movement can not cater to the model`s flying need, the servos movement can be changed.CH1 is for ailoren, ch2 for elevator,ch3 for motor, and ch4 for rudder.
Receiver Specifications Operating voltage：4.8V~5.2V Current drain： ≤40mA Weight：12g dimension：44mm*23mm*15mm Channels: 6 Channels Reception system：GFSK Range(Height)：≥350m Adjacent channel rejection：≥-85dBm± 16kHz Function For operating helicopter Operation for aeroplane 6. 襟翼 5. Undercarriage 6. Pitch 5. Gyro gain 4. Rudder 4. Rudder 3. Throttle 3. Throttle 2. Elevator 2. Elevator 1. Aileron 1. Aileron www.art-tech.
Electrio speed controler Specifications for ESC-30A Working currency:30A/50A(max currency） input voltage：DC,5V-14.4V. starting mode：adaptable point（1.0ms-1.5ms） control mode：200 class proportional output voltage(BEC) ：5V/1A(direct for servo ) To batte ry To receiv er To moto r To batte ry Auto cut-off function When the voltage of battery in model plane is under working voltage, ESC has the function of cutting the power to the motor and only supply to receiver in order to save power.
Operation for transmitter and servo For operating helicopter (Mode 1) Before adjusting, please be familiar with transmitter operation and servo(Below description in case of all neutral) Ailoren Operation Joystick for ailoren left forward plane moves left Joystick for ailoren right forward plane moves right Elevator Operation Joystick for elevator up forward tail is up,and plane will go downforward Joystick for elevator down forward tail is down,and plane will go upforward Throttle Operation Joystick is
Operation for transmitter and servo Operation for aeroplane (Mode 1) Before adjusting, please be familiar with transmitter operation and servo(Below description in case of all neutral) Ailoren Operation Joystick for ailoren righ forward the right ailoren up and left ailoren downand vice versa Elevator Operation Climb upforward Operation Joystick for elevator is down forward, the elevator is up,and tail is down, then the plane will climb up, and vice versa Operation for throttle Joystick for throttle is
Adjustmen order Open the battery bay, and range the 8 cells AAA battery into the battery bay, then close the bay.Before adjustment, change the reverse switch to the lower positon(Nor). Open the transmitterand the receiver, and do the following steps: 1.check every servo`s movement and make sure every movement of control arms and servo arms is correct If not, please change the switch for reverse. 2.
Explaination for Technical words Here are some technical words used in this Manual Aileron:Either of two movable flaps on the wings of an airplane that can be used to control the plane's rolling and banking movements Elevator:A movable control surface, usually attached to the horizontal stabilizer of an aircraft, that is used to produce motion up or down. Rudder:A similar structure at the tail of an aircraft, used for effecting horizontal changes in course.
There will be no notice while changes caused by improving. Without permitting,it is forbidden to do copy of the content of this manual. www.art-tech.
