ANGEL Remote control helicopter Operating manual R
CATALOG ★SPECIFICATIONS 02 ★CAUTION 03 ★TIPS FOR SAFETY 03 ★CHARGE MODE AND WARNING 05 ★SAFETY INSTRUCTIONS FOR LI-POLY BATTERIES 06 ★PARTS LIST 07 ★OPERATION MANUAL METHOD STARTING PROCEDURE 07 ★FUNCTIONS FOR CONTROL SET 08 ★ADJUST THE SPEED OF THE ROTOR BLADES BY THE PCB BOARD 08 ★SWASHPLATE ADJUSTMENT 09 ★MAIN ROTOR BLADE ADJUSTMENT 09 ★GROUND EFFECT 09 ★NORMAL FLIGHT 10 ★INSTALLATION 11 ★PARTS REPLACING 13 ★THE POSSIBLE PROBLEMS AND SOLUTIONS 14 ★SPARE PARTS LIST 15 17-3
Thank you for purchasing our latest product--Angle 300 electric R/C helicopter. This helicopter is a typical coaxial dual rotor helicopter and it’s our latest product. The frame is made of the high-strength plastic and configured with scale flashers for night flight. This helicopter is super stable, easy to control and it has a great maneuverability and accuracy. Moreover, this product has a vivid flying gesture and it is crashresistant.
CAUTION R/C modeling is a hobby with high technology and should not be considered as a toy. There is risk involved during the operation of this product and the user should take all precautions seriously or serious body injury may occur, it is only suitbale for the person above 14 years old. Improper disassembly, improper adjustments or setup may lead to unsatisfactory or unsafe operation.
TIPS FOR SAFETY 2. Obtain the assistance of an experienced pilot. The help of an experienced pilot will ensure that you will have a well trimmed, correctly functioning helicopter for the first flight. It is strongly advised that you first practice on the simulator prior to making a flight with your new helicopter. Novice Novice 3. Always be away from the running parts During the operation of your helicopter the rotor will be spinning at a high rate of speed.
CHARGE MODE AND WARNING Li-Po battery(balance changer) ATI-0910 Li-poly battery balance charger using instruction 12V D C Power supplier Specifications: Input voltage: DC 10V~15V Output voltage: DC 7.4V&11.1V (To 2 or 3 cell Li-poly battery) Charge current: 0.3A~1.0A (Can be continuously adjusted) Indicator state: Green: Charge complete or no battery Red: Charging Flash: Drip current charging Separated battery detection: The voltage of any battery reaches 4.2V, the charge of it will cease automatically.
SAFETY INSTRUCTIONS FOR LI-POLY BATTERIES 01.Do not disassemble or reconstruct the battery. 02.Do not short-circuit the battery. 03.Do not use or leave the battery nearby the fire, stove or heated place. 04.Do not immerse the battery in water or sea water, do not get it wet. 05.Do not charge the battery nearby the fire or under the blazing sunlight. 06.Do not drive a nail into the battery, strike it by hammer or tread on it. 07.Do not impact or throw the battery. 08.
PARTS LIST The helicopter includes the following parts, please check to make sure that all of the parts are included in your kit. If there is anything missing please contact your local dealer. Fuselage Transmitter Balance Charger Li-po battery Operating manual OPERATION MANUAL METHOD Please follow the following process before starting, Otherwise, it may lead to the helicopter not to work. 1. Put the helicopter on the flat ground and put the transmitter one meter away from the helicopter. 2.
FUNCTIONS FOR CONTROL SET Mode 2(left hand throttle) Throttle Max Rudder left Elevator down Rudder right Aileron left Throttle Min Aileron right Elevator up Ch3 (throttle) Trim adjustment Ch2 (elevator) Trim adjustment Ch4 (rudder) Trim adjustment Ch1 (aileron) Trim adjustment LED Indicator Power switch Reverse switch on CH4(rudder) Reverse switch on CH3(throttle) Reverse switch on CH2(elevator) Reverse switch on CH1(aileron) ADJUST THE SPEED OF THE ROTOR BLADES BY THE PCB BOARD * Motor 1 * M
SWASHPLATE ADJUSTMENT 1. Swashplate check. Pull down the throttle joystick and throttle trim to the lowest position, and push the elevator trim and aileron inching switch to the neutral position, and check whether the swashplate is in a horizontal level. 2. Swashplate adjustment: If the swashplate is not in a horizontal level, adjust via the following steps: First, loosen the swashplate pull rod (Disconnect the ball buckle with the swashplate).
NORMAL FLIGHT Ascending Left stick pushing up Descending Left stick pulling down Head turning left Left stick moving left Head turning right Left stick moving right Right stick pushing up Head forward Head backward Right stick pushing down Helicopter moving left Right stick moving left Helicopter moving right Right stick moving right Chart for R/C mode 2(left hand throttle) 10 www.art-tech.
INSTALLATION 13 14 15 16 17 18 19 20 12 21 22 23 11 65 10 24 9 8 25 7 26 27 6 28 5 29 30 4 31 3 32 2 10 1 34 42 41 40 39 38 37 36 33 35 48 47 46 45 44 43 11 www.art-tech.
INSTALLATION 56 57 55 58 54 59 53 60 52 61 51 62 50 63 49 64 1 The fixed sleeve for main shaft 18 Nut 35 Left tail blade cover 52 Servo arm 2 Upper main gear 19 Balance bar sleeve 36 LED light 53 Screw 3 Lower main gear 20 Ba lance bar ball buckle 37 LED light seat 54 Copper gear 4 Servo arm steel wire 21 Stabilizer 38 Tail blade shaft 55 Screw 5 Inner inclined tray 22 Screw 39 Tail blade 56 Motor 6 Outer inclined tray 23 Rotor head 40 Right tail blade cover 57 Ser
PARTS REPLACING Swashplate assembly Tail wing assembly 2. Put ③ into ④. 1. Put ② into ①. Upper rotor wing grip installation Please follow the sketch map to install the upper rotor wing grip. Main rotor shaft and core shaft installation Press step 1 into step 2 to form a new compenent. Please follow the sketch map to assembly the tail wing Lower rotor wing grip installation Sketch map of upper rotor wing grip.
THE POSSIBLE PROBLEMS AND SOLUTIONS Problem The model does Reparation Cause Check the battery voltage of transmitter and receiver Use completely charged batteries Check the wire connection inside the model Contact the local dealer Thruthle protecting function swiched on Minimize the right joystick of thrutle (See page 8) Improper starting operation Restart the model (See page 7) The model flies beyond the control distance Control the flying distance The stabilizer of the balance bar is off Ins
SPARE PARTS LIST No:4R011 Body No:4R021 Undercarriage No:4R031 Frame No:4R041 Battery box set No:4R0 5 1 Swash plate No:4 R0 6 1 Main blades No:4 D101 Main rotor wing grip No:4 R071 Main gear set No:4 R081 Core shaft No:4R141 Stabilizer No:4R091 Bearing set No:4R101 Rotor head set 15 www.art-tech.
SPARE PARTS LIST No:4R111 Arm set No:3R021 Controlling board (PCB) No:4R131 Motor set No:4D051 Li-poly battery No:35051 Servo No:4J011 Upgraded carbon blades No:4R121 Searchlight 16 www.art-tech.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
