Installation Instructions

C200
Composite detection alarm
CO / Smoke
The photoelectric composite detector is used for
the detection of CO gas or smoke. In order to
ensure the safety of home life, it is recommended
to install composite alarm detectors in bedrooms,
corridors, lofts, basements and other places. The
product is powered by a DC 9V battery. When the
detector gives an alarm, it will emit an alarm
sound of ≥85dB, and the alarm light will flash at
the same time. The detector has a low-voltage
alarm function and a button alarm mute or test
f u n c t i o n . T h e d e t e c t o r u s e s l o w - p o w e r
technology, and the theoretical battery is replaced
once a year.
Ø Support three major alarms: smoke + CO +
wireless transmission network alarm;
Ø Full y s nap- i n paten t ed str u cture , s impl e
installation, no need for debugging and wiring;
Ø 360 all-round detection of smoke alarm, no
dead ends, reliable;
Ø Built-in high-sensitivity induction technology,
reliable, safe;
Ø Built-in 85dB sound and light alarm, effective
reminder evacuation site;
Ø Adopt ultra-low-po w e r mi c r o processor +
photoelectric principle technology, ultra-long
standby life battery use for 3 years;
Ø Low battery alarm function, when the battery
voltage lower than 6.8V, It will make warning
tone out;
Ø T h e h o u s i n g i s d es i gn e d t o f ul l r o ta r y
detachable buckle of easy maintenance
Power voltage
Gas detection
DC9V(6F22 battery)
CO and Smoke
 Set the host in the “Align” mode;
‚ Press the C200 (TEST) key, the device beeps
while transmitting wireless signals
C200 and receiving alarm host pairing method:
[TEST] key two functions
Ø In the alarm state, press the [TEST] key, the
product stops alarming
Ø In the non-alarm state, press the [TEST] key,
the device alarm light blinks and sounds, and
wireless signals are transmitted
Ø Do not install near doorways, windows, fans,
etc., because this place generally has fast air
circulation, which will affect the sensitivity of
the alarm.
Ø Do not install in locations with high tide
temperatures, such as bathrooms, top floors, or
temperatures above 50 ° C or down to minus 10
° C.
Ø Do not install in places with high temperature
and high wind speed, otherwise it will affect
the sensitivity.
Ø In order to keep the sensor working efficiently,
the sensor needs to be cleaned every 6 months.
Remove the battery first, then swipe the dust
with a soft brush, and then put the battery back
into the battery box.
Ø Abnormal temperature can also cause false
alarms. Just let the air in the space circulate
and the alarm sounds stopped. Dust will also
reduce the sensitivity of the alarm. Please
improve according to the cleaning method
above.
 Poo r p o wer sup ply: Afte r i n sta l lin g th e
battery, the product does not respond.
Solution: Check whether the positive and negative
poles of the battery are reversed (compared with
the positive and negative poles on the case),
whether the battery is sufficient, and whether the
battery is in good contact with the shrapnel.
‚ Gas interference false alarm: product alarm
when no gas leakage occurs
Solution: Check whether there are irritating items
in the room, such as paints, pigments, alcohol,
etc., or someone smokes an excessive amount of
cigarettes; Can cause false positives)
ƒ Poor self-test: Pressing the [TEST] key has no
response during product use
Solution: If the battery power is poor, you need to
check the power supply problem, if the power
supply is normal, you need to return to the factory
for repair
Two test alarm methods:
Method 1: Press the [TEST] key, the product
alarm light flashes and sounds at the same time;
Method 2: Use CO gas or smoke to enter the
smoke port from the side of the product, the alarm
light will flash and sound at the same time. (As
shown below)