TB-01 Specification V1.0 TB-01 Specification Version V1.0 Copyright ©2019 Copyright © 2019 Shenzhen Ai-Thinker Technology Co.
TB-01 Specification V1.0 Disclaimer and Copyright Notice The information in this article, including URL addresses for reference, is subject to change without notice. This document is provided "as is" without warranty of any kind, including any warranty of merchantability, fitness for a particular purpose, or non-infringement, and any warranty of any proposal, specification, or sample mentioned elsewhere.
TB-01 Specification V1.0 Document development/revision/revocation resume Version Date V1.0 2019.11.25 Copyright © 2019 Revised content First developed Shenzhen Ai-Thinker Technology Co.
TB-01 Specification V1.0 CONTENT 一、 INTRODUCTION....................................................................................... 错误!未定义书签。 二、 SPECIFICATION........................................................................................ 错误!未定义书签。 三、 DIMENSION............................................................................................. 错误!未定义书签。 四、PIN DEFINITION..................................................................................................................
TB-01 Specification V1.0 1.INTRODUCTION The TB-01 intelligent lighting module is a Bluetooth module based on the EP2S12F40 chip and compatible with BT 4.2 low-power Tmall Genie Mesh. This module supports the Bluetooth module directly controlled by Tmall Genie and has a Bluetooth mesh networking function. Peer-to-peer network communication, using Bluetooth broadcast for communication, can ensure timely response in the case of multiple devices.
TB-01 Specification V1.0 LIST 1 Main Parameters Model Name TB-01 Size 22.0*14.0*2.0(±0.2)MM Wireless Standard Bluetooth V4.2 Frequency Range 2400 ~ 2483.5MHz Output Power 10dBm Max Sensitivity -92dBm Interface PWM Work Temperature -20℃ ~ 70 ℃ Store Temperature -40 ℃ ~ 125 ℃ , < 90%RH Voltage Range Voltage 2.7V ~ 3.6V, Current≥50mA Deep Sleep Mode:0.9uA Power Sleep Mode:1.9uA Mesh Mode:30mA Transmission distance Copyright © 2019 80m ~ 150m Shenzhen Ai-Thinker Technology Co.
TB-01 Specification V1.0 2.SPECIFICATION Electrical characteristics Absolute Maximum Rating Any exceeding the following absolute maximum ratings may cause damage to AB1611 Item Min Typical Max Voltage 2.7V 3.3V 3.6V I/O Voltage (VCCIO) -0.3V - 3.6V Work Temperature -20℃ - +70℃ Store Temperature -40℃ - +125℃ Recommended Operating Conditions Item RF Voltage(VCCRF) Min Typical Max - 1.2V - RF Specification Output Power Item Average Power Min Typical Max 8.5dBm 9.
TB-01 Specification V1.0 3.DIMENSION Copyright © 2019 Shenzhen Ai-Thinker Technology Co.
TB-01 Specification V1.0 4.PIN DEFINITION The TB-01 module has a total of 7 interfaces. For example, the pin diagram, the pin function definition table is the interface definition. TB-01 Pin diagram PIN function definition sheet No.
TB-01 Specification V1.0 5.SCHEMATIC 6.DESIGN GUIDE 1、Application circuit 2、Antenna layout requirements (1) For the installation position on the motherboard, the following two methods are recommended: Solution 1: Place the module on the edge of the motherboard, and the antenna area extends beyond the edge of the motherboard. Solution 2: Place the module on the edge of the motherboard, and the edge of the motherboard hollows out an area at the antenna position.
TB-01 Specification V1.0 3、Electricity Supply (1) Recommended 3.3V voltage, peak current above 50mA (2) It is recommended to use LDO power supply; if using DC-DC, it is recommended to control the ripple within 30mV. (3) The DC-DC power supply circuit is recommended to reserve the position of the dynamic response capacitor, which can optimize the output ripple when the load changes greatly. (4) 3.3V power interface is recommended to add ESD devices.
TB-01 Specification V1.0 Connection diagram 5、LED Drive Reference Design TB-01 module application only needs 3.3V power supply and simple driving circuit to achieve intelligent light control. Take MOS tube to drive a channel of white light as an example, the design reference is as follows; CW_I is the module's positive white light PWM output , Q1 is MOS tube, WW is LED lamp beads, the other 4 road lamp driving circuit is the same as this road design method.
TB-01 Specification V1.0 7.REFLOW PROFILE Copyright © 2019 Shenzhen Ai-Thinker Technology Co.
TB-01 Specification V1.0 8.PACKAGING As shown below, the packaging of TB-01 is taping packaging. 9.CONTACT US Company Website:https://www.ai-thinker.com Development DOCS:http://docs.aithinker.com Official Forum:http://bbs.ai-thinker.com Sample Purchase:https://anxinke.taobao.com Business:sales@aithinker.com Technical Support:support@aithinker.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AHMR-TB-01 Or Contains FCC ID: 2AHMR-TB-01” When the module is installed inside another device, the user manual of this device must contain below warning statements: 1.