User's Manual

ManualsBrandsShenzhen AEE Technology ManualsElectronicsAerial photography equipment

Disclaimer

Please read this disclaimer carefully before using the product of Quadcopter. This product is not suitable for people under the age of 18. By using this

product, you hereby agree to this disclaimer and signify that you have read them fully. You agree that you are responsible for your own conduct and

content while using this product, and for any consequences there of. You agree to use this product only for purposes that are proper and in accordance

with the terms and any applicable or guidelines AEE may make available.

1. Shenzhen AEE Technology Co., Ltd. reserves the right of final interpretation of this disclaimer.

2. Any part of this disclaimer is subject to change without prior notice.

3. This disclaimer is available in multiple languages. In case of any discrepancy, the Chinese version shall prevail.

4.For more detailed or latest product information, please visit www.aee.com.

AP11

 Takin

and Landin

g(O

utdoors

)

Takin

S2 S3 S4

GPS

NRM

F M

S1: S2: S3: S4:

GPS

1) Place Quadcopter (with full power battery) on a flat and open ground,

and ensure Tail Indicator faces toward you.

2. Turn on the remote control, repeater and camera and enable the Wi-Fi

function of the camera in sequence; last, turn on the aircraft (Do Not turn on

the aircraft before the Wi-Fi function of the camera is enabled);

3) Be sure the Remote control is set exactly as the figure below.

4) Starting motors: toggle the left joystick to left bottom corner and toggle right joystick to right bottom corner at the mean time to start motors. Once

the motors start please release the joysticks immediately.

5) Push the left joystick slowly, then Quadcopter take off. Please refer AEE Quadcopter User Manual for more details.

Note: The motors can not be started until GPS signal is ready (Tail Indicator (green) remains on).

1. Upon startup, the airborne camera and the repeater will pair with each other. Please wait for about 30S to ensure that pairing is completed, so

that the airborne camera can record videos normally.

2. After the aircraft is powered on, the aircraft and the PTZ will start self-test. Do not shake the aircraft or the PTZ at this moment; otherwise, the

aircraft and the PTZ will fail the self-test.

(The PTZ can be used only when the camera is installed; otherwise the PTZ may be damaged)

3. Before installing the camera onto the aircraft, it is suggested that the auto standby function of the camera should be disabled.

4. When the aircraft complete searching for GPS satellites, the tail light (green) will remain on. During flight, please do not turn the joysticks of the

remote control to a lower toe-out pattern, which will stop the motors.

Landing：

1) Slowly pull the left joystick to lower Quadcopter until it touches the ground(only on flat and open ground).

2) After landing, pull the left joystick to the lowest position and hold for more than 3 seconds until the motors stop.

3) Power off Quadcopter by sliding the switch to OFF.

4) Remove the battery.

5) Power off Remote control and Wi-Fi Repeater.

Important:

1) Control the flight height under your control during your first flight.

2) Do not stop the motors during flight, or it will cause the Quadcopter to drop without control.

AP11

Remote control and Wi-Fi Repeater Description

Remote control

(U.S. Mode)

LEFT

FORWARD

LEFT

TURN

LEFT

TURN

RIGHT

TURN

RIGHT

BACK

DOWN

Quadcopter Direction

(" " indicates nose direction)

Note: The Remote Control is set to U.S. mode by default.

[ 1 ] Propeller [ 2 ] Motor [ 3 ] Front Indicator [ 4 ] Landing Gear

[ 5 ] Camera [ 6 ] 3-Axials Gimbal [ 7 ] Quadcopter Battery [ 8 ] Tail Indicator

[ 9 ] Power Switch [ 10 ] Rear Indicator [ 11 ] Battery Level LCD Segment Display

[ 12 ] Battery Level Check Button

[ 1 ]

[ 2 ]

[ 3 ]

[ 4 ]

[ 7 ]

[ 5 ]

[ 6 ]

[ 8 ]

[ 9 ]

[11]

[10]

[12]

Power Switch

Charging Port

(mini USB port)

Pairing Button

Repeater Base

Power Indicator

Wi-Fi Indicator

Lock Screw

Strap Hole

Right Joystick

Video Stop Button

Remote Control

Power Switch

Photo Shooting &

Video Recording Indicator

Flight mode switch S4

Angle control switch S3

Wi-Fi Repeater

Repeater Base

Antenna

Smartphone Holder

Calibration switch S2

Speed control switch S1

Power Indicator

Status Indicator

Left Joystick

Airborne Video

Recording Button

Return button

Airborne

Shutter Button

S2 S3 S4

GPS

NRM

F M

Hook open/close button

Summary of content (3 pages)

PAGE 1
Remote control and Wi-Fi Repeater Description AP11 Remote control (U.S.
PAGE 2
AP11 Quadcopter Quick Start Guide 1 3 Download AEE App (iOS / Android) To install the AEE AP App onto your smartphone by scan QR code. Preparing the Remote control 1) Load four AA batteries into the battery compartment. Pay attention to positive and negative directions. 客户二维码待客户更改 Scan QR Code above Remove the Buckle and Install the Camera Two types of cameras can be installed onto the aircraft AP11: 1. AEE S50/S51/S60/S71/S70/OM51S/OM60S/OR60S/ OR71S/S40; 2. Gopro G3/G4.
PAGE 3
FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.