8 寸超薄人脸体温检测识别终端 8-inch ultra-thin Face Recognition Body Temperature Detection Terminal 适用于闸机、壁挂式、桌面式、落地式安装 Suitable for Brake machine, wall-mounted, desktop, floor-mounted installation 型号: 适用于办公区域、酒店、通道闸机、写字楼、学校、商场、商店、社区、建筑工地等公共服 务及管理项目等需要用到人脸门禁的场所。 Model: Suitable for office areas, hotels, passage gates, office buildings, schools, shopping malls,shops, communities, construction sites and other public services and management projects where face access control is required.
产品特性 Product Features 1、宽动态单目活体防伪,彻底解决各类照片在各种载上的欺骗; 1. Wide dynamic monocular living anti-counterfeiting, completely solving the deception of various photos on various uploads; 2、支持 LED 智能补光; 2. Support LED intelligent fill light; 3、支持串口、韦根 26、34 输出,输出内容支持配置; Support serial port, Wiegand 26-bit, 34-bit output, and support output content configuration; 3、实时体温监控,体温公差范围精准到 0.3°,体温检测距离 0.3-0.5 米; Real-time body temperature monitoring, and body temperature tolerance range is accurate to 0.
7、支持公网、局域网使用部署方式; Support public network and local area network management 8、支持屏幕显示内容配置; Support screen display of content configuration 9、支持识别距离配置。 Support identifying distance configuration 环境要求: Environmental Requirements: 使用过程中应避免的情况: Conditions to be avoided during use: ①传感器在室外使用时受环境影响较大,应在室内环境使用 ①The sensor should be used in indoor environment because it is greatly influenced by the environment when used outdoors ②由于红外传感器的特性,在使用环境中,如传感器正对窗户、空调、暖气 片等高温物体,会严重影响测量准确性 ②Because of the characteristic of
screen 分辨率 Resolution 1280*800,亮度 500cd 1280 * 800, brightness 500cd 处理器 Processor CPU 4 核 cores,RK3288 内存 RAM DDR3 2GB ISP 图像处理 Image Processing 内置双路 ISP Built-in dual-channel ISP 本地储存 Local storage Tf 卡 Tf card 8GB 配件 Accessories 补光灯 Fill light 红外、LED 灯 Infrared, LED lights 读卡模块(预留) Card reader module (Reserved) IC/ID 读卡器、身份证阅读器 热成像体温检测模块 IC / ID card reader, ID card reader and thermal imaging temperature detection module 网络模块 Network module 支持有线,2.
buttons 功能 Functions 常规参数 General parameters OTG 接口 OTG port 1 路 In Channel 1 本地离线使用 Offline locally use 本地 2W 人脸库 20 thousand local face database 人脸检测 Face Detection 支持同时检测跟踪 5 个人 Support simultaneous detection and tracking of 5 people 1:N 人脸识 1: N face recognition 支持万分之一的误识率,99% 的 通 过 率 Support one in 10,000 error recognition with 99% pass rate 1:1 支持选配刷卡模块, 身份证模 块可实现 1:1 人脸比对 Support optional card swiping module, ID card module which can realize 1: 1 face identification 陌生人检测 Stranger detect
工作温度 Operating temperature -10℃-60℃ 工作湿度 Working humidity 10%-90% 静电 Static electricity 4K/8K 电池辐射 Battery radiation 无频点超标 Not exceeded 功耗 Power consumption 5W MAX 设备重量 Equipment weight 约 1.6KG About3.5 lbs 设备尺寸 Equipment size 373.
用户管理 User Management 设备管理 Equipment management 关于本机 About this machine 其它 Others Menu interface 模块,管理等。 Menu style and human-computer interaction, how to enter other modules, management, etc.
外形尺寸 Dimensions 刷卡体温 Body temperature of scanning face 标准体温 Standard body temperature 安装说明 Installatio n instructio ns A 外观部 分指示 说 明 A Instructio
ns for appearance 闸机头示意图如下图所示。 The schematic diagram of the gate is shown in the figure below.
注意:此时不要连接网线、电源线等,避免安装麻烦。 Note: Do not connect the network cable, power cable, etc. At this time to avoid installation trouble ③在闸机下方,将线缆及线缆接口依次穿过垫片、螺母,将螺母对准螺纹拧紧,如图所示。 Under the gate, pass the cable and cable interface through the washer and nut in sequence, and tighten the nut to the thread , as shown in the figure.
①将桌面式置于桌面上,人脸设备放置在支架上方两“L”型卡位上调整好角度即可;适用 于前台访客处。 Place the desktop on the desktop, and place the device on the two "L" card positions above the bracket and adjust the angle; It is suitable for the front desk visitors.
手量尺寸若有误差,以收到实际产品为准 If there is any mistake with hand measure, subject to the actual product. 注意:锁紧螺丝前,请保证所有尾线不被螺丝压破,造成短路。 Note: Before tightening the screws, please ensure that all the tail wires are not crushed by the screws, causing a short circuit. ②贴墙式:将不锈钢壁挂件从人脸设备上取下,在墙面上适当高度置于不锈钢板,用笔做标 注,冲击钻钻四个孔位,胶塞置于孔内,用自攻螺丝先将不锈钢板固定于墙上(如果尾线从 底盒后部出来需要在墙上适当开洞,方便走线;如果尾线从底部出来,只需要用白色大塑料 线槽固定和走线),如图所示! ②Wall-hanging type:Firstly, remove the stainless steel wall hangings from the device.
put the stainless steel plate on the wall at an appropriate height, drill four holes with an impact drill, place the rubber plug in the hole, fix the stainless steel plate to the wall with tapping screws.( If the tail wire comes out of the back of the box, it is necessary to make a hole in the wall to facilitate the wiring. If the tail wire comes out from the bottom, it only needs to be fixed and routed with a large white plastic trunking.) As shown in the figure.
开关信号 Switch signal 韦根输入 Wiegand input 韦根输出 Wiegand output 232 信号 signal 232 8 寸人脸识别尾线说明 8-inch face recognition tail wire description 闸机头尾线(7 根)seven gate tail wires USB2.0 接口 USB2.0 interface 12V 电源输入 12V power input 重置/复位按键 Reset / Reset button 开关信号 Switch signal 韦根输入 Wiegand input 韦根输出 Wiegand output 232 信号 signal 232 RJ45 有线网口 RJ45 wired network port 壁挂尾线(5 根)5Wall-mounted tail wires USB2.0 接口 USB2.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
注:图片和文字说明最终解释权归本公司所有!