ORIGINAL 2.4GHz X4 2.4GHz Instruction Manual ShenZhen WFLY Technology Development Co.,Ltd. www.wflysz.
Packed content Before using , please make sure you must understand the following information. When Opening the package, please confirm the following items are complete. Match the different parts of the assembly the article is also different, please confirm it according to the following chart. If mixed with the counterfeit product which result in damage, the company shall not be responsible for it Please use this book or catalogue which have recorded the products.
Contents Important Notes Logo Meaning Attention Point For The Using Of 2.4GHz System Attention Point For The Using Of High Speed Mode Attention Point For The Driving Attention Point For The Battery Attention Point For The Saved And Wasted Battery.
Contents Product Features Can Store 40 Sets Of Model Data Special Brake Mixing For Large Car (BRAKE) Anti Lock Braking System (A.B.
Contents Function Description 42 Advanced Function Programming Of Mixed Control A.B.
Important Notes In order to ensure the safety of yourself and others, when using this product, please pay attention to the following matters. Logo Meaning The following logo appears in the book, indicate the safety consideration, please pay special attention to. Danger Warning Careful Circular logo: Ignorance of this logo and the operation error, may lead to the user or others to death and injury risk.
Important Notes Items Needing Attention While Driving Warning Driving is forbidden during the Rainy day, strong wind and night the transmitter cannot operate ,control or lost its way after dropping it into the water . No driving in the following places. • Near the crowded people . • Near the high voltage electricity or communication station. • Whenever the interference of waves, obstacles or transmitter, or the vehicle fault cause body out of control , it may cause other people death .
Important Notes Careful Please check the function of losing control protection is normal before driving Confirmation method: 1, Open the transmitter first and then open the receiver power; 2, set the lose control of protection function connect to the receiver (39 pages); 3, turn off the transmitter; 4, confirm the function under the lose control protection the throttle and channel can operate in a setting position.
Important Notes Avoid nickel-cadmium batteries falling from a high place cause strongly hit. Strongly hit the battery may cause the battery short circuit, abnormal heat, damaged battery fluid leakage Cause burns or chemical damage. Be sure to the battery should disconnected. when the exercise is no longer operate Do not plug in the socket.when the charger is not charging Avoid abnormal heating accident.
Terms Of Use Attention For The Mode Setting Of Steering Response Warning If you want to use the X4 high speed steering response mode, you must meet the following conditions: With the 6V 270Hz specifications: digital servos. The 6A nickel cadmium battery the using power for the receiver . The transmitter steering response mode setting: high speed mode (refer to page 53). When using the simulated steering, be sure to transform the response mode of X4 steering into the normal mode .
Terms Of Use The Using Method Of Transmitter The Name Of Each Part Of The Transmitter Antenna Display Status indicator The power switch Return key Debugging indicator DT1 Menu key Steering wheel Roller and define key DT2 Rings SW2 0 1 2 Slide switch (SW.2) The trigger DT2 DT3、DT 4 Button (SW.1) A brief description of the battery installation 1, as shown in the picture to open the battery compartment cover. 2, the battery removed. 3, replace the new battery.
Terms Of Use When you Close the battery cover, please don't let the lid nip the connected line of battery. If the cable is clamped which cause a short circuit, will be outbreak of fire, abnormal heat, cause burns or fire.
Terms Of Use Grip Lever Operation Button initial setting is the timer operation button. Operation mode is divided into: 1, the standard, press down is effective bounce is invalid; 2, switch, each time you press will switch the state of ON/OFF . The Adjustment Method Of Mechanical Range In accordance with the user's operation feeling, when you want to reduce/enlarge the trigger. Braking travel, please adjust this place. Adjustment method: 6 angle screwdriver rotation diagrams of using the 2.
Terms Of Use Method For Replacing The Left And Right Hand In order to meet different operation habits of users,We use the switch design of multiple modes operation! Methods ① Tools: 2.
Terms Of Use Methods Left And Right Hand Replacement Of The Steering Wheel Assembly This structure lack of a steering rocker arm, The steering wheel is directly installed on the main body, simple and flexible! Another operating options available for different operating habits of users! ① Pay attention to the direction wheel part of unloading screw.
Terms Of Use Methods No Arm Rocker Operation Mode Change ①Remove the steering wheel rocker four inner six angle screw, open cable; ②The unloading of the wheel shaft inner six angle screws and three long six angle screw; ③Delete the rocker, connect the cable, take the steering wheel seat corresponding to the position of three screw hole install the screw.
Terms Of Use Using Method Of Transmitter Antenna And Receiver Antenna Related Matters During the operation, please try to tune the antenna to the vertical position, otherwise it will shorten the distance of the remote control. Careful During the Driving, do not hold the antenna. When Adjusting the antenna range, do not exceed the range of the rotatable antenna.
Terms Of Use Receiver Code Method Each transmitter has a separate distribution ID number. In order to successfully operate, the receiver must be paired with transmitter. Once the pairing is completed, an ID number can be received and store, after using it does not need repairing.
Terms Of Use The Installation Method Of Receiver Do not trim or bundling antenna. Don't bend coaxial cable, which may cause damage. The antenna is installed in a higher position. The antenna is sheathed in the pipe to protect it. Please try to make the receiver stay away from battery, electronic speed controller, motor or metal wiring and other noise sources. Please use the foam to pack receiver and thick version of double-sided adhesive tape fixed to achieve the shock effect.
Terms Of Use Assembling Method Receiver And Servo Connections Connect between receiver and servos according to the following diagram When Connection and installation please follow the "safety precautions of the assembled" (9~13 pages). The following connection method only for reference ,for the actual connection way please change according to different accessories. Connecting the method of electrically adjustable ,battery motor depends on the type of electrically adjustment .
Terms Of Use Safety Considerations When Assembled Warning The Receiver Antenna Can not be cut off or messy tie the antenna. The receiver antenna can not be connected with the servo connection line and electronic transmission line. Do not close to the motor or power battery which is parts of large current flow at least the distance is 1CM.
Terms Of Use Warning Electronic Gearbox When installing the cooling plate, please do not contact the aluminum or carbon alloy chassis and other easily conductive material Brush Motor Disturbance Countermeasures Use the brush motor please make sure to install the container of the eliminating the noise interference.
Terms Of Use Initial Set-up The Preparation Before The Transmitter Sets Set The Function Of Transmitter, Please Confirm And Set The Following ①~④ Items. Turn on the power, the main interface will display the model number of the currently selected, if you need to change, please use the model selection (see page 51). Model No. Battery Voltage Model Name Fine Tune Monitor Timer AT L \DR Monitor Channel Monitor 1 The Rf Signal Output Validation Turn the power switch to the "PWR ON" , RF can be normally o
Terms Of Use 4 Fine-tuning The Initial Setting Check Adjustment Of 1 DT1 The initial setting , trimming 1 function is the direction. Move the fine adjustment to confirm the direction fine adjustment on the T1 graphics get the corresponded movement. Check Adjustment Of 2 DT2 The initial setting, tuning the 2 function is the throttle trim. Move the fine adjustment to confirm the throttle trim move on the T2 graphics.
Terms Of Use Switch, Button Description Return Menu Power Switch Roller / Confirm Digital Trim 3 Digital Trim 1 Digital Trim 4 Digital Trim 2 Slide Switch Throttle trigger Steering Wheel Button Power switch: push to the end point is the power off , push the end point of PWR ON is the normal boot , push the DISP ON is the emission function boot off. Throttle trigger: pull the trigger is accelerated; push forward to the trigger is the brake or reverse.
Product Features •Model memory for 40 models Each model can be set independently for the name of the model . If you use the model copy function you can simply set the existence of subtle differences model. •large car brake mixing The front and the back of the brake Mixing can be individually adjusted for 1/5GP car. •The anti lock brake system In order not to let the engine in the uneven corner or when the moment of braking which will cause the brake function of slipping.
Function Chart Main Page/ Directory Structure 30
Function Chart 31
Function Chart Function Table Function Table Function Abbreviation Function Description PAGE D/R Rudder rudder angle adjustment function 33 EXP(STEER) Steering motion curve adjustment 33 SPEED Delay function of the Steering action 34 EXP(THR) The movement of the throttle curve adjustment 35 SPEED Delay function of the throttle action 36 TH ACC Throttle start-up characteristic adjustment function 37 REV Reverse function of the steering action 38 TRIM The endpoint position adjustment
Function Description Direction[STEER] The Size Of The Action[D/R] The positive and negative stroke of more simply way of the adjustment direction passage . The maximum is set to 100, the full stroke, The direction of travel depends on its travel set; The minimum is set to 0, the channel have no action, no matter how much travel set.
Function Description Direction Delay[SPEED] When the fast steering movements, the body may suddenly lost control, or the danger of slip. The use of Direction delay function can avoid the occurrence of danger. Turning Deficiency Turning Transition Whitour "SPEED" Smooth Transition Whit "SPEED" •Respectively adjust the steering wheel rotate outward and the recovery speed of action. 0 100 the fastest, do not delay. the slowest speed, maximum delay.
Function Description Throttle[THR] Exponential Curve[EXP(THR)] This function can make the throttle accelerate and the brake more sensitive or flat (corresponding to the electrically adjustable or throttle actuator),its adjustment does not affect the maximum stroke of throttle setting. Brake Curve[EXPB] 0 ~- 30 0 accelerator flat. uniform linear accelerator. 0 ~+ 30 accelerator sensitive. Suggestions: When the road surface and surface grip good, make the curve set in the "0~+30 ".
Function Description Throttle Delay[SPEED(THR)] On the wet and slippery road the violence throttle operation will only cause the wheel slip so that the vehicle can not normally go forward. Set the throttle delay can prevent the waste of energy and allows you to enjoy a more smooth operation. The function have no effect on the throttle trigger back and brake (only for acceleration). 0 100 acceleration without delay. acceleration maximum delay.
Function Description Accelerator[TH ACC(THR)] The gas pedal, brake moment adjusting movement by the side near the midpoint. Adjust the forward of gas pedal and near the midpoint of the brake moment movement . 0 100 near the midpoint will not produce the moment acceleration. near the midpoint produce the strongest instantaneous acceleration motion. As The Parameter Increases, the effect will increase! Accelerator is Influenced by the travel set.
Function Description Primary Setting [PRIMARY] Positive And Negative Setting [REV] Aiming at the throttle, direction, channel 3, channel 4, change the movement direction of servo , each channel independently set. Note: Please Set The Positive And Negative According To The Actual Direction Of The Model Car! Set: Main Menu → PRIMARY → R EV Digital Trimming[TRIM] Midpoint +20% Make the throttle, direction, channel 3, channel 4 of neutral point amount of motion give compensation.
Function Description Travel Set[EPA] Implement the most flexible stroke adjustment, can respectively adjust the throttle, direction, channel 3, channel 4 A Direction of travel, without affecting another directional stroke of the different channel . When the vehicle steering character is different it should be a corresponded change in the EPA values of steering gear.
Function Description Position[POS] This function is to make the channel 3, 4 preset in a fixed position. During the adjustment of the following functions, channel 3, 4 of the action will be based on hybrid control execution, rather than fixed in a preset position: * PR MIX * BK MIX * 4WSMIX * ESCMIX Action channel 3, 4 can be set in fine tuning (DT1/2/3/4) or switch (SW.2), the specific operation please refer to the functional selection.
Function Description The Calculation Of The Time Total time =1 lap + 2 lap +3 lap +... Case: *When the car run the first lap, short press the button to record time of 1 minutes and 5 seconds, the total time is 1 minutes 5 seconds; *When the car is running second laps, short press the button to record time of 1 minutes and 15 seconds, the total time is 2 minutes and 20 seconds.
Function Description Advanced Settings Programming Of Mixed Control [PR MIX] Move throttle, direction, channel 3, channel 4 can be arbitrarily mixing. The main channel: select the input channel of the mixed control. Auxiliary channel: select output channel of the mixed control. The main channel of the action will be mixing to the auxiliary channel. The ratio of the left: the ratio of the negative end. Mixing output range: -120% ~ +120% The right ratio: the mixing ratio of the positive side .
Function Description A.B.S Make the model car to generate intermittent braking action, namely point type brake. A.B.S Diagram X:Y Duty Cycle X: Braking Y: Brake Gap Brake amount Trigger point Brake returns A Cycle No configuration A.B.S trigger operation direction Trigger point: A.B.S trigger position action. 0 as long as the brake it will generate A.B.S action. 50 The brake reached 50% produce A.B.S action. 98 brake reached 100% produce A.B.S action. Returns: the return of the brake.
Function Description Brake Mixing[BK MIX] When the Front and back wheel brake must separately control and adjust, you can use this function. This function provides 3 kinds of control methods. 1, the throttle channel control rear brakes, channel 3/4 to control the front wheel brake. 2, the throttle channel control rear brakes, channel 3 and channel 4 to control the front wheel brake.
Function Description Four Wheel Steering[4WSMIX] The action of the direction channel through the mixing control make the channel 3 control the back wheel movement . Ratio: the action of the direction channel according to the set ratio mixed control to channel 3. Set to 0, the direction channel movement is not mixed control to channel 3. Set to 100, the direction of channel action 100% mixing to channel 3.
Function Description Front And Back Of The Miscible Flooding[ESCMIX] Throttle channel action. through the mixing make the channel 4 control the front wheel. Ratio: The throttle channel action according to the set ratio mixing to channel 4. Set to 0, the throttle channel action does not mixing to channel 4. Set to 100, the throttle channel action will mix to channel 4 absolutely .
Function Description Throttle Mode[TH MODE] The Midpoint Rate[SXNT] Select the acceleration and braking action ratio is 7:3 or 5:5. Acceleration Direction 5:5 Brake Direction Acceleration Direction 7:3 Brake Direction Set: Main Menu → ADVANCE → TH MODE → SXNT Idle Speed[IDLUP] Improve the idle speed oil vehicle.so that it can improve the starting performance of the engine. The midpoint of the throttle will make a compensation correction when accelerating or braking.
Function Description The Midpoint Of The brake[NTBRK] Execute braking at throttle of the neutral position. Set to 0, no brake. Set to 100, 100% brake. Midpoint Brake Application: 1 , Direct setting, function can take effect. 2 , The switch is set to the midpoint of the brake [NTBRK], through changing the start of the switch or stop the function. Set: Main Menu → ADVANCE → TH MODE → NTBRK Throttle Off [THOFF] The throttle action set at a fixed location. Set the throttle position, 0 for the neutral point.
Function Description Function Selection [DIAL SW] The operational function of setting switch ,fine adjustment and setting the mode of action. Switch, Button Set switch, button, switch function. Button (SW1) switching mode: Each switch, press switch ON/OFF state. Standard: when pressing down is ON ,release is OFF . The button function could be assigned as shown below: TIMER ESCMIX 4WSMIX THOFF PR MIX IDLUP A.B.
Function Description Fine Tuning Options Set the digital tuning to operational function ,step forward. The step is set to 1~20. Fine adjustment direction: standard and reverse. Digital tuning function could be assigned as shown below: ST-TRM 4WSMIX TH-TRM BK4-RT SPEED BK3-RT ACCBK PMX-R ACCFW PMX-L CYCL THOFF ABS.DY ESCMIX ABS.
Function Description Model Information[MODEL] The X4 transmitter can store 40 sets of model data This menu selection, copy, reset model. And can set the name of the model . Model Selection 40 sets of model can store and select. Set: Main Menu → MODEL→ M ODEL Model Replication Can Selected the currently model data copy to another model data, do not to change the current model data Setting. This can be a simple setting only subtle difference for the model.
Function Description System Settings Adjustment When the throttle and steering wheel will make the mechanical deviation, use calibrational function to correct. Setting method: 1,According to "neutral" prompt, put the trigger, the runner on the midpoint, press the confirm key. 2,According to the prompt "endpoint" , put the trigger ,wheel into the midpoint struck several times respectively ( lightly lean is ok, as the following graph), stop on the middle point at last press confirm key.
Function Description Power Supply Scheme[BATT] Please select the correct power supply solutions! The use of different batteries need to select different power supply scheme. Of course, if not chosen properly, will not cause damage to the transmitter. But it will affect the life of the battery. When you hear the continuous warning tone, indicates the battery voltage is too low, please replace the new battery. Standard power supply voltage: 3.7~6.5V Four battery scheme: Common battery (3.
Reference Transmitter Product type: X4 Model application: car , boat Frequency range: 2.400GHz-2.483GHz Power: ≤ 100mW Code: DSSS Language: Chinese, English Storage capacity: 40 groups Resolution: 1024 The power supply voltage: 3.7~6.5V Controllable range: about 100m (related to the use of the environment) Receiver Product type: WFR04H Apply to: model car, boat Frequency range: 2.4GHz-2.483GHz Modulation : PPM/PCMS 1024 Resolution: 1024 The power supply voltage: 3.7V-6.0V, ≤ 60mA Size: 34.85x21x11.
FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
EN201310V0.
