RADIO CONTROL SYSTEM PCMS 4096 PCMS Receiver, Dual MCU, Dual Antenner.
INSTRUCTION Thank you for purchacing product! SERVICE 1.Retailers to provide free maintenance for six months (apart from artificial damage) 2.
INSTRUCTION CATALOGUE Contents-------------------------------------------------------------------Transmitter front----------------------------------------------------------Transmitter back----------------------------------------------------------Receiver--------------------------------------------------------------------Trainer function-----------------------------------------------------------Flying safety warnings---------------------------------------------------Features---------------------------------
INSTRUCTION 5. Sub trim---------------------------------------------------------------6. Swash param setting-----------------------------------------------7. Auxiliary channels setting-----------------------------------------8. Throttle curve setting-----------------------------------------------9. Pitch curve setting--------------------------------------------------10. Revolution mixing--------------------------------------------------11.
INSTRUCTION AIRPLANE SYS SETTING 1.Model selecting---------------------------------------------------------- 73 2.Model name-------------------------------------------------------------- 74 3.Model setting------------------------------------------------------------ 75 4.ATL------------------------------------------------------------------------ 76 5.AIL-2---------------------------------------------------------------------- 77 6.Modulation setting------------------------------------------------------ 78 7.
INSTRUCTION 13.Throttle Cut Setting-------------------------------------------------- 99 14.Idle Down-------------------------------------------------------------- 100 15.Fail Safe--------------------------------------------------------------- 101 16.Timer------------------------------------------------------------------- 102 17.Advanced-------------------------------------------------------------- 103 ADVANCED (1). curve Setting---------------------------------------------------------- 105 (2)-(8). PROG.
INSTRUCTION 7.RF Setting---------- -------------------- --------------------------------- 8.Stick Setting-------------------------------------------------------------9.Adjustment-------------------------------------------------------------10.Reset Setting----------------------------------------------------------11.Send Data--------------------------------------------------------------12.Receive Data----------------------------------------------------------13.
INSTRUCTION Contents Thank you for your attention and support to WFLY radio! WFLY promises every WFT09S radio control system include the following contents: 1. 4096 transmitter 2. Battery holder for transmitter 3. Neckstrap 4. Trainer cable/Data transfer cable 5. Simulator cable 6. WFR09S 2. 4GHz 9 channel receiver PCMS 7.Li-po Voltage Regulation 8. English instruction manual.
INSTRUCTION Contents 1. Transmitter 2. Transmitter battery holder 3. Neckstrap 4. Trainer cable/Data 5. Simulator cable transfer cable 7.Li-po Voltage Regulation 8. CD manual 9 6. WFR09S 2 .
INSTRUCTION TRANSMITTER MODEL NO.: MODULATION: PPM, PCMS 1024, PCMS 4096 OUTPUT POWER: ≤100mW POWER SUPPLY: 9.6-12V CURRENT DRAIN: 250mA Band: 2.
INSTRUCTION TRANSMITTER BACK DSC Battery cover 11
INSTRUCTION RECEIVER Resolution 4096 (with PCMS 4096 modulation) 2.4GHz 9 Channels receiver Dual MCU, Dual antenna, Dual circuits , Resolution 4096 receiver MODEL NO.: WFR09S TYPE: 9 CH PPM /PCMS 1024/PCMS 4096 BAND: 2.400-2.483GHz POWER SUPPLY: 4.8-6V RECEIVER SENSITIVITY: - 97dBm WEIGHT: 14.8 g DIMENSION: 44.8mm x27.9mm x16.
INSTRUCTION Trainer function Two WFT09SII transmitters can transfer data and realize trainer function. Setting Method: 1).Data transfer function: use Trainer cable/Data transfer cable to connect two WFT09SII transmitter. Select “Send data/receive data” in SYS setting to transfer the data. 2).Trainer function: use Trainer cable/Data transfer cable to connect two WFT09SII transmitters. Insert RF module to the trainer transmitter, student transmitter doesn’t insert the RF module.
INSTRUCTION FLYING SAFETY WARNINGS Special Symbol Instruction To use the product safely, please pay attention to the instruction as follows. Please pay special attention to the symbol as follows: Dangers：If you use it without proper operation, it is possible to hurt you seriously or may even cause death. Warnings：If you use it without proper operation, it may make you or others to hurt badly or may even cause death, and it may cause slight hurt or damage to things.
INSTRUCTION FEATURES Computerized transmitter High Speed, High Resolution, optimized 2.
INSTRUCTION Buttons MENU Menu button brings you to the function list of the transmitter. EXIT Exit button is to back the previous menu or exit edit. + This button is to increase the value. If you press it for a while, the increasing speed will be faster. This button is to decrease the value. If you press it for a while, the decreasing speed will be faster. Cursor buttons Move the cursor. OK The button in the middle of the direction buttons is the OK button.
INSTRUCTION WFLY 2 . 4 G H z O p e r a t i o n i n s t r u c t i o n s 2.4G system can automatical l y r e c o g n i z e W F L Y P C Ms a n d P P M . 1 .Code matching Description This function is useful under the situation when the transmitter need to be match and bind with receiver. setting Enter "normal settings" and choose "advanced", use up and down key to choose coding, press ok to select. The screen will display "OK: Cancel".
INSTRUCTION Adjust the stick head: Top thread Allen key Stick head Put the stick head cover the control rod on the left and right sides,don't twist down the stick head to the bottom, and then put top thread with allen key to adjust the height Stick you need. Twist the top thread down from here, the height of the stick head depends on the depth of the top thread.
INSTRUCTION change the throttle direction of mode1 or 2: Bolt 4 Bolt 1 Bolt 2 Bolt 3 Take the metal chip and the screw down, and put it on the similar position of the right side . Set up release link and springer, according your habit to addjust the the tightness of screw 2 to adjust the control feeling. Take repositor and spring down, and put it on the left side of the location of corresponding.then twist bolt 1 down until withstand the adjust nail in case adjust nail will move away.
HELICOPTER INSTRUCTION HELICOPTER Press Menu and turn on the transmitter to enter SYS SETTING. Select MODEL SETTING, press OK button to select the model type. Restart the transmitter after setting.
HELICOPTER INSTRUCTION Editing mode and function introduction 1. Opening Screen Turn on the power switch, the LCD displays as follows. Voltage Timer A Start time Model type Timer B Throttle trim display Timer C Elevator trim display Rudder trim display Aileron trim display The opening screen displays the voltage, timer, model, aileron, throttle, elevator and rudder state. Note: Press EXIT you can see the model name. Model name 2. Menu Screen There are “Normal setting”, “SYS setting”, “Advanced”.
HELICOPTER INSTRUCTION B. SYS SETTING Press Menu and turn on the power switch, the LCD displays as follows. Setting method: 1. Use direction button to select the editing part,use up/down buttons to select function item. Left/right direction button to turn page. 1. MODEL SELECTING 2. MODEL NAME 3. MODEL SETTING 4. ATL 5. MODULATION SETTING 6. SWASH SELECT 7. STICK SETTING 8. ADJUSTMENT 9.REST SETTING 10.SEND DATA 11. RECEIVE DATA 12. SOUND 13.CONTRAST SETTING 14. ENGINEER MODEL 15. ABOUT 16. LANGUAGE 2.
HELICOPTER INSTRUCTION SYS SETTING 1.Model selectting There are 85 helicopter models. You can select any one to set. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model selecting”, OK button is to enter editing. Steps: 1. Use up/down direction button to select the model. 2. Press OK button to select. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 2. Model name This function is to make new names by users. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model name”, OK button is to enter editing. Steps: 1. You can edit the underlined letter. 2. Press OK button to choose the word you like. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 3. Model setting You can select the model type. There are three type: HELI, ACRO, GLID. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Model setting”, OK button is to enter editing. Steps: 1. Use up/down direction button to select the model type. 2. Press OK button to confirm. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 4. ATL Adjustable travel limit (ATL) makes throttle trim effective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set ATL to OFF.
HELICOPTER INSTRUCTION 5.Modulation setting Because of the different receiver modulation PPM/PCMS1024 /2.4G PCMS4096, the transmitter should be accordance with the receiver modulation. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Modulation setting”, OK button is to enter editing. Steps: 1. Use direction buttons to select the editing part. 2. Press OK button to confirm. Restart the transmitter and it works. 6.
HELICOPTER INSTRUCTION 7.Swash select There are 6 kinds of swash. You can select the swash you preferred. If you use 120 degree CCPM helicopter, the servos will realize mix function automatically. Please select the swash according to your helicopter swash type.
HELICOPTER INSTRUCTION 8.Stick setting There are 4 kinds of model, you can use up/down direction button to select the model you preferred. 1-aileron 2-elevator 3-throttle 4-rudder Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Stick setting”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. 2. Press up/down button to choose Stick mode. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 9.Adjustment This function is to set the central, high and low point of four sticks when users changed the mode I or II by themselves. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “ADJUSTMENT”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. Take the aileron adjustment for example . 2. Make the stick in the mid-point location.
HELICOPTER INSTRUCTION 10.Reset setting This function is to back default. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Reset setting”, OK button is to enter editing. Steps: 1. Use direction button to select the editing part. 2. Press +/- button to back default. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 11. Send data Two transmitters (WFT09S) can copy data by a trainer cable/data transfer cable. This function together with the next function “Receive data” can realize the data copy. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Send data”, OK button is to enter editing. Steps: 1. Select the model data you want to send out. 2. Press OK to send.
HELICOPTER INSTRUCTION 12.Receive data Two transmitters (WFT09S) can copy data by a trainer cable/data transfer cable. This function together with the previous function “Send data” can realize the data copy. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Receive data”, OK button is to enter editing. Steps: 1. Press OK to receive data. 2. Restart the transmitter after receiving the data and it works.
HELICOPTER INSTRUCTION 13.Sound This function is to select the sound ON and OFF. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “SOUND”, OK button is to enter editing. Steps: 1. Use +/- button to select ON and OFF. 2. Press OK button to confirm. 3. Press EXIT after setting.
HELICOPTER INSTRUCTION 14.Contrast setting This function is to adjust the LCD brightness by increasing or decreasing the contrast value. Setting Method: Press Menu and turn on the transmitter to enter “SYS SETTING” Use up/down button to select “Contrast setting”, OK button is to enter editing. Steps: 1. Use +/- button to increase or decrease the value. 2. Press OK button for a while is to back default. 3. Press EXIT after setting. 15.About This item shows the Version of WFLY radio.
