User's Manual

ManualsBrandsShen Zhen WFLY Technology Development ManualsElectronicsRadio Control Transmitter

15. TIMER

16. More setting

(1). GYRO sens setting

This function is to control two electronic clocks used to keep

track of time remaining in a competition time allowed, flying time

on a tank of fuel, amount of time on a battery, etc.

A good gyro will totally eliminate the need for revo.mixing.

The gyro wil sense and correct the unwanted motion for you,

so you don’t have to spend time to get a complex curve operating

properly. It simplifies adjusting/selecting the gyro sensitivity,

and can provide more than 2 gyro gain settings. (The higher the

gain, the more correction the gyro provides and the “softer” or

less responsive the helicopter feels) This function makes the

best possible use of the infight adjustable gain of most gyros.

Setting Method

Use up or down button to select TIMER, OK button is to enter

editing.

Steps:

1. Use direction buttons to select editing part.

2. Use +/- button for proper adjustment,

3. Press EXIT after setting.

WFT09

INSTRUCTION

Summary of content (16 pages)

PAGE 1
WFT09 INSTRUCTION 15. TIMER This function is to control two electronic clocks used to keep track of time remaining in a competition time allowed, flying time on a tank of fuel, amount of time on a battery, etc. Setting Method Use up or down button to select TIMER , OK button is to enter editing. Steps: 1. Use direction buttons to select editing part. 2. Use +/- button for proper adjustment, 3. Press EXIT after setting. 16. More setting (1).
PAGE 2
WFT09 INSTRUCTION Setting Method Use up or down button to select GYRO sens editing. Steps: 1. Use direction buttons to select editing part. 2. Use +/- button for proper adjustment, 3. Press EXIT after setting setting , OK button is to enter (2). Throttle hovering setting (3). Pitch hovering setting This function is to set the throttle curve trim at the hovering point.
PAGE 3
WFT09 INSTRUCTION (4). HI/LO PIT setting This function is to set the high and low pitch position at different flying modes. (5). Trim offset setting This function is to adjust the servo trim at hovering state. Optional separate trims in addition to those for the normal condition. This function is used to automatically change the trim of a helicopter, for example, when transitioned from hover to flying at high speed.
PAGE 4
WFT09 INSTRUCTION (6). DELAY This function is to delay the aerobatics or throttle cut when the helicopter is in the air so that to avoid the big trim change. The Delay function provides a smooth transition between the trim positions whenever OFFSET, REVO. MIXING, or THROTTLE HOLD functions are turned on and off. Set up a delay on all 3 channels to ease the transition from one flight condition to another so there are “hard jumps”. Steps: 1. Open the DELAY function. 2. Adjust AIL response as needed.
PAGE 5
WFT09 INSTRUCTION (8). Swash and THR mixing This function is to adjust throttle and pitch mix function. (9). Cur ve Setting There are 2 kinds of setting, Normal and Advanced.
PAGE 6
WFT09 INSTRUCTION (10)-(16). PROG. NOR. MIX1-7 The mix program is to adjust the flying pose. There are 7series programs with the same set method. (17)-(20). PROG. CUR. MIX1-4 There are 4 serious curve mix program, the curve is made up by 2 to 11 point.
PAGE 7
WFT09 INSTRUCTION (21). Throttle needle mixing Throttle needle is a pre-programmed mix that automatically moves an in-flight mixture servo in response to the Throttle Stick imputs for perfect engine tuning at all throttle settings. This function is particularly popular with contest pilots who fly in a large variety of locations, needing regular engine tuning adjustments, and requiring perfect engine response at all times and in all maneuvers.
PAGE 8
WFT09 INSTRUCTION SYS SETTING 1.Model selectting There are 10 helicopter models. Setting Method Use up or down button to select Model selecting, OK button is to enter editing. Steps: 1. Use direction buttons to select the model. 2. Press OK button. 3. Press EXIT after setting. 2. Model name This function is to make new names by users. Setting Method Use up or down button to select Model selecting, OK button is to enter editing. Steps: 1. You can edit the underlined letter 2.
PAGE 9
WFT09 INSTRUCTION 3.ATL Adjustable travel limit (ATL) makes the channel 3 TRIM LEVER (THROTTLE TRIM) effective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, youmay want trim operation the same as on all other channels. To do so, set ATL to OFF. Setting Method Use up or down button to select Model selecting, OK button is to enter editing. Steps: 1.
PAGE 10
WFT09 INSTRUCTION 5.Swash select There are 6 kinds of swash. You can select the swash you preferred. Setting Method Use up or down button to select Model selecting, OK button is to enter editing. Steps: 1. Use +/- buttons to select the model. 2. Press OK button to choose. 3. Press EXIT after setting.
PAGE 11
WFT09 INSTRUCTION 6.Stick setting There are 4 kinds of model, you can use up and down direction button to select the model you preferred. Setting Method Use up or down button to select Stick setting , OK button is to enter editing. Steps: 1. Use up and down direction buttons to select the model. 2. Press OK button to choose. 3. Press EXIT after setting.
PAGE 12
WFT09 INSTRUCTION 7.Fail safe This function is to set responses in case of loss of signal or low RX battery. Setting Method Use up or down button to select Fail safe, OK button is to enter editing. Steps: 1. Use direction buttons to select editing part. 2. Choose Channel to change. 3.Set and confirm fail safe conmmand. 4. Press EXIT after setting. 8.Rest setting This function is to back default. Setting Method Use up or down button to select Reset setting, OK button is to enter editing.
PAGE 13
WFT09 INSTRUCTION 9. Send data This function is to send the model parameter to another transmitter. By using a trainer cord, one transmitter can send the data to another transmitter. Setting Method Use up or down button to select Send data, OK button is to enter editing. Steps: 1. Select the model data you need to send out. 2. Press OK to send.
PAGE 14
WFT09 INSTRUCTION 10.Receive data This function is to receive the model parameter to another transmitter. By using a trainer cord, one transmitter can receive the data from another transmitter. Setting Method Use up or down button to select Receive data, OK button is to enter editing. Steps: 1. Press OK to receive data. 2. Restart the transmitter after receiving the data.
PAGE 15
WFT09 INSTRUCTION 11.Contrast setting This function is to adjust the LCD brightness by increasing or decreasing the contrast value. Setting Method Use up or down button to select Contrast setting, OK button is to enter editing. Steps: 1. Use +/- button to increase or decrease the value. 2. Press OK button for a while is to back default. 3. Press EXIT after setting. 12.Engineer model 13.About 14.Language This function is to select the language, Simplified Chinese and English can be selected.
PAGE 16
WFT09 INSTRUCTION TO THE PILOT WFT09 is the first version. Thank you for using the radio. We welcome your valuable advice and we will make progress of the radio. Welcome to contact us! www.wflysz.com sales@wflysz.