WFT07 2.4GHZ MULTI-LANGUAGE REMOTE CONTROL DEVICE 7 CHANNELS INSTRUCTION MANUAL V1 Attention ▲ pls read the instruction before using the product ▲ Please keep this manual ww w . wf lysz .
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Thank you for purchasing the WFLY product WFT07 Features 1.The large dot matrix LCD display: multi-language, graphical display. simple design, easy operation. 2.Original 2.4G technology : use of data transfer, greatly improve the handling agility. fully express the fast Lightning : (Note: is WFLY exclusive technology). 3.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL CONTENTS 1 1 2 3 4 5 6 7 8 9 9 10 WFT07 Remote control device contents WFT07 Remote control device WFT07 RC device parts of the name(front) WFT07 RC device parts of the name( back) Instructions of the 2.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL CONTENTS Advanced settings 1.Speeder mixing 2.Fail safe 3.code match 24 24 25 Airplane Functions system settings 26 27 27 27 27 27 27 27 27 27 27 Input mode and functions 1.Model parameters 2.Model settings 3. Coaching / Simulation 4.Control stick settings 5.Control stick calibration 6. Restore factory settings 7.Tone settings 8.Contrast settings 9.Power supply scheme 10.Version information Preferences 27 27 27 27 27 27 27 28 28 28 29 29 29 29 29 1.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL WFT07 Remote control device contents 1.WFT07 remote control device 1 set 2. WFR07S 2.4G hz rece ive 3.Simulat or switch cable 1 Root 4.Transmitter 4cell battery case 1 A 5.Manual 1 This/zhang 6.WFLY neck strap 1 On ly 1 Ar ticle WFT07 remote control device diagram 1.WFT 07 remot e control device 2.WFR0 7S 2.4Ghz receive 3.Si mul ator swi tch cable Man ual WFT07 2.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL WFT07 RC device parts of name WFT07 RC device Positive (Right hand throttle) Antenna(rotatable) Power light RF light Buzzer K1 K2 V1 K3 K4 Throttle trim Aileron/ throttle stick Elevator trim Rudder/ elevator stick Power switch Neckstrap attachment Rudder trim Aileron trim Left Menu Up Right Exit Add Down Reduce LCD OK K1: 2 stalls. Throttle holding and throttle cut K2: 3 stalls. Timer , airplane 5channel and airplane Elev-flap mixing.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL WFT07 RC device parts of name WFT07 RC device back Handle Trainer/DSC Battery cover 3
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Instruction of 2.4Ghz receiver Model:WFR07S Type: 7channel 2.4Ghz receiver,4096 resulotion(in the PCMS 4096 resolution) (Adaptation WFLY 2.4Ghz series),ORGANIC 2.4G Voltage :4.8V-6V Current:30mA Weight:9.6g Size: 40.42mm x27.27mm x11.88mm Frequency: 2.400GHz-2.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL WFT07 instructions of the code match 1.Remote control device settings ● unction instruction: The remote control for the 2.4G spread spectrum, frequency hopping systems, have high antiinterference. The remote control has unique address identification code information, Before use the remote control,pls match the code with the 2.4Ghz receiver. ● Settings Into the "Advanced Settings" menu item under the "Preferences" .
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Trainer Function Instruction of the Training function The same two remote control devices WFT07 can do the Trainer function: Settings: 1. Using the simulator cable to connect two WFLY equipment. 2. Trainer settings: Press MENU key to boot into the "System Settings" function, enter " Training / simulation "menu,selected the" trainer mode ", (effect after re-boot ). 3.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Note the special symbol For the safe use of this product, pls pay attention to The marks have the following description of symbols. Dangers: If you use in without a proper operation,it is possible to hurt user seriously injury or may even cause death .
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Instruction of the input function MENU: After booting, press the menu button to enter the function menu - Preferences. In addition, if the in the function interface, press this key will be Back to the menu. EXIT: Press this key, you can return to the previous menu level, or exit the edit state. Add/Reduce Key: Can be used to adjust values. Also set numerical value, press + / -, can accelerated settings the functions.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Adjustment of stick head Allen Key Top thread Stick Head Put the stick head cover the control rod on the left and right sides,don't twist down the stick head to the bottom,and then put top thread with allen key to adjust the height you needed. Stick Twist the top thread down from here,the height of the stick head depends on the depth of the top thread.
WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Replacement the throttle of mode 1 or 2 Right-hand man will lose their own free replacement warranty program Bolt 3. Bolt 2. Bolt 1. Bolt 4. Set up release link and springer,according your habit to adjust the tightness of screw 2 to adjust the control felling. Put on the matel chip,according your habit to adjust the elasticity of screw 3 and screw 4 to adjust the damp of throttle control felling.
Helicopter Functions WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Helicopter Functions Introduction This section are mainly introduces the helicopter functions. Please press the MENU button to turning on the radio in turing off state, you can enter the "System setting” menu, Up / Down arrow keys to select" Model Settings ", press the Enter key to enter the function setting interface, (as above).
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 2 . Function Menu - There are “System settings”,”Preferences”and “Adcanced settings” A. System Settings In close state, hold down the MENU key, then turning on the power, you can enter the "System Settings" menu page, the interface as shown. In this state, all functions can be set one by one. As follows: 1. Use the arrow keys on the screen to select the functions you needed, use up and down keys to select function items.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL System Settings Menu Introduction 1.Model Parameters ●Function Model parameters function totally have three machines for the user to choose, you can select any of them model to settings. ●Settings Press the MENU button to boot into the “System Settings" menu, use Up / Down keys to select the "model parameter settings", and press the “OK ” key into the function interface, as shown above. The steps of setting is as follows: 1.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL ●Settings Press the MENU key to boot into the "System Settings" menu,use Up / Down arrow keys to select the "trainer / Simulator", press OK key to enter the function interfacet, as shown above. The steps of setting is as follows: 1, first to use the up / down arrow keys to edit the selected item. 2. Press OK button to confirm, then press the right arrow keys to determine. Reboot to take effect. 4.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 6.Restore factory settings ●Function Reset function is to present the model all the data back to the initial default settings, so can do Comprehensive settings of re-work. Procedures. ●Settings Press the MENU key to boot into the "System Settings" menu, use Up / Down keys to select "reset ", press Confirm key into the function interface.As above: The steps of settings is as follows: 1.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 9.Power supply scheme ●Function The machine can use a variety of power options: If ordinary alkaline AA batteries 4S, Ni-MH / Ni-Cd battery 4S, Li-Ion / Li-polymer battery 1S. Different battery in different low-battery voltage alarm, in order to extend battery life, select the corresponding power supply plan. Note:Voltage range 3.7V-6V.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL Introduction of the Parameters Settings Menu 1.Monitor CH 1 CH 6 CH 2 CH 7 CH 3 CH 4 CH 5 ●Function The monitor function is to monitor and confirm the channel operation state. ●Settings In the "Preferences" interface, use Up / down keys to select the "Monitor", press OK key to enter the function interface, as above.Then can monitor each channel action condition 2.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 4. Settings exponential EX, can change the aileron, throttle and rudder these three channels' joystick sensitivity near the neutral. Dual rate and curve exponential are match, will have a lot of combinations and settings, with the arrow keys to select the "EX" in the screen, settings way are same as "D / R" . 5. Use the arrow keys to select the curve point, + / - key to changing the value of curves point. 6.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 5.Sub Trim ●Function When the electronic trim can not make the servo to achieve a satisfactory angle, be corrected by the function, can make the servo to reached a ideal angle which user wanted.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL ●Settings In the "Preferences" interface,use Up / Down keys to select the "throttle curve settings", press OK key to confirm enter the function interface, as above. The steps of settings is as follows: 1. Flight status (normal or stunt). Use the arrow keys to enter edit state, you use + / - keys to select one of the curve, then enter the following settings. 2.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 10.Throttle holding Settings ●Function Throttle holding settings can set in when throttle cut landing , fixed the throttle servo in the a low speed position , throttle holding position can be adjustment within ± 75% . Switch K1 work for this function. ●Settings In the "Preferences" interface,use Up / Down keys to select the "throttle holding settings", press OK key to confirm enter the function interface, as above.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 12.Swash Swash type selection ●Function If using a helicopter with CCPM, connecting a cross-shaped piece of servo will automatic going the mixing action. Please use the helicopter swash according to the type of choice. This remote control device offers two modes: normal, and 3CH120 (CCPM) mode.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 13.Gyro Sens Mixing ●Function Can adjust the gyro sensitivity directly from the transmitter, you can choose AVCS gyro (GY) and ordinary gyro (STD). Gyroscope sensitivity switch plugs into the 5 channel of the receiver. This time 5channel in front of the auxiliary channel setting is temporarily non-functional,switch sensitivity by flight mode (Normal stunt lock) .
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL Introduction of Advanced Setting Menu 1.Speeder Mixing Settings ●Function Speeder mixing settings is under the case have the speeder, uses and settings the speeder . In the state can set the output action servo. ●Settings Into the "Preferences" under the Advanced Settings "menu.use Up / Down keys to select the" Speeder mixing settings ", press the OK key to confirm enter the interface. The steps of settings is as follows: 1.
WFT07 REMOTE CONTROL DEVICE Helicopter Functions INSTRUCTION MANUAL 3.Code Match ●Function This remote control are the 2.4G spread spectrum, frequency hopping systems, with a high anti-interference. Each remote control only has an identification code information, before you use the remote control system pls matched with the 2.4G receiver which including in this device. ●Settings Into the "Preferences" under "Advanced settings" menu.
Airplane Function WFT07 REMOTE CONTROL DEVICE INSTRUCTION MANUAL Airplane Function Introduction This section are mainly introduces the airplane functions. Please press the MENU key to boot, you can enter the "System settings”item,use Up / Down keys to select" Model Settings ", press the OK key to enter the function interface, (as Shown). Please choose the model, re-boot, the transmitter can display the functions of airplane. Following description the details of each function.
WFT07 REMOTE CONTROL DEVICE Airplane Function INSTRUCTION MANUAL Introduction of System Settings Menu 1.Model parameters Selection Refer the instroduction on page 13 2.Model Setting Selection Refer the instroduction on page 13 3. Coaching / Simulation Selection Refer the instroduction on page 13 4.Stick settings Selection Refer the instroduction on page 14 5.Stick calibration Selection Refer the instroduction on page 14 6.
WFT07 REMOTE CONTROL DEVICE Airplane Function INSTRUCTION MANUAL 8 Flap trim ●Function This feature is for 6 channels to do the trim stick action. ●Settings Press the power key to boot into the "parameter settings" menu, use Up / Down keys to select the "Flap trim", press OK key to enter the function interface, as above. The steps of settings is as follows: 1. Using the up / down keys can choose to the edit item. 2. Selected the options, press the + / - key to edit the data.
WFT07 REMOTE CONTROL DEVICE Airplane Function INSTRUCTION MANUAL 11 Throttle Curve Settings Selection Refer the instroduction on page 19 12 Throttle Cut Settings Selection Refer the instroduction on page 20 13 Throttle Holding Settings Selection Refer the instroduction on page 21 14 Timer Selection Refer the instroduction on page 21 Advanced Settings Menu 1 .
WFT07 REMOTE CONTROL DEVICE Airplane Function INSTRUCTION MANUAL 2.Ele-Aileron Mixing ●Function This feature is to allow elevator to work in the aileron mixing function. Notes: Ele--aileron mixing, V-tail , Ele- flaps can not be opened simultaneously, if the screen displays "warning", please forbid the other mixing functions, then turn on this function. ●Settings Into the "Preferences settings" under "Advanced Settings" menu .
WFT07 REMOTE CONTROL DEVICE Airplane Function INSTRUCTION MANUAL 4.Aileron-2 ●Function Aileron -2 is aileron another channel 's distribution. ●Settings Press the MENU key to boot into the "System Settings" menu, use Up / Down keys to select the "aileron -2", press the OK key to enter this function interface, as above. 5 Fail Safe The step of settings is as follows 1. Using the + / - keys to choose different models. 2. Selected the options, press OK key to confirm. 3.
SHENZHEN WFLY TECHNOLOGY DEVELOPMENT CO.,LTD Room 618-619,6/F Chuangye Building, No.1 Qilin Road, Nanshan District, Shenzhen 518052, P.R.China Tel:+0755-26581815 Fax:+86-755--26585126 http:// www.wflysz.com Email:sale2@wflysz.com Thank you for purchasing WFT07 remote control device, pls read the instructions carefully before use it.