User's Manual

Speaker accessories:
Technical parameters
Wireless function
External audio AUX input function
Conponents function description
Udisk function
Indicator Status
Wireless is not connected: blue light fast flashing.
Wireless connected: blue light stop flashing.
Play music: blue light slow flashing.
Using the environment and storage environment
Epoch1 user manual
52
Infrared remote control function
1. Operating environment
Temperature: 0 ~ 40 DEG C, humidity: 0% ~ 85%RH.
2. Storage environment
Temperature -30 ~ 60 DEG C, humidity: 0% ~ 90%RH.
1
2
3
4
5
6
7
8
9
1. Volume up/previous song 2. Volume down/next song
3. Music play/pause button
4. Mode switch key(switch to COAX/USB/AUX/BT modes)
5. Power on/off button 6. Coaxial digital audio input socket
7. U-disk/USB interface 8. 3.5 mm AUX input socket
9. Type-C power input interface (9V2A)
NO. NAME MODE
WIRELESS UDISK AUX/COAX
1
CLICK :PLAY/PAUSE ; CLICK:PLAY/PAUSE; CLICK TO MUTE
2
+
CLICK TO VOLUME
UP;LONG PRESS TO
PREVIOUS SONG
CLICK TO VOLUME
UP;LONG PRESS TO
PREVIOUS SONG
CLICK TO
VOLUME UP
3
_
CLICK TO VOLUME
DOWN ;LONG PRESS
TO NEXT SONG
CLICK TO VOLUME
DOWN ;LONG PRESS
TO NEXT SO NG
CLICK TO
VOLUME DOWN
OPERATION
COA X USB AUX DC -9V
COAX USB AUX DC-9 V
1. In the boot state ,as shown, connected the audio cable for your device and the
speaker.
2. You can press the "COAX" button of the remote control to enter the coaxial mode
or press the mode switching button once to the coaxial audio mode on speaker,
at the speaker changed successful you can hear a beeps .
3. Set digital audio output from your TV first (setting--sound–digital audio output--
select PCM/ setting--sound–coaxial output--ON) .
4. Long press “+” “-” button to volume up/down.
5. Short press “ ” button to mute.
NOTE: Please select audio source output of the TV, can not be used directly.
Speaker connect to TV’S SPDIF/COAXIAL interface
Coa xial
COAXIAL MODE
Troubleshooting
1.No sound in Coaxial audio mode
Please confirm the speaker whether Coaxial mode is currently entered ,press the
“COAX” button of the remote control to enter the coaxial mode or unplug the Udisk
and AUX audio cable ,restart the speaker and short press the “M” button to enter
the coaxial mode.
Set digital audio output from your TV first (setting--sound–digital audio output--
select PCM / setting--sound--coaxial output--ON), devices compatibility will be vary,
see your device’s documentation for more information to set.
2.Unable to boot
Please charge the battery, and the charging LED indicator light is red;
Use the reset button to reset (the operation method is indicated on the second page
of the manual).
3.No sound
Is the mute function turned on or the volume adjusted to a minimum?
Press the mute button to close the function or turn up the volume.
4.The remote control does not work
Is the battery exhausted ? Change a new battery.
Is the distance between the remote control and the speaker too far? Get close to
the device.
Is the remote control aimed at the infrared receiver?
Aim the remote control at the middle part of the speaker .
5.Wireless cannot connect
Please confirm the speaker whether wireless mode is currently entered (the blue
indicator will flash quickly in wireless mode).
Restart the speaker, delete the phone’s wireless record and search for a new pair.
1 Connected the power supply to the speaker at first, long press the power button
about 3 seconds, the blue light will be flashing and accompanied by boot sound,
then the wireless speaker has been in standby search status.
2 Open the phone's wireless function, searched the speaker's wireless - -
name : "Fosurul Epoch 1" and paired, when the speaker connected successfully,
a sound will beep, at the same time, the blue light stop flashing, you can start
using the speaker to play music; the next time with the same device matching,
the speaker will automatically to connected.
☆Power Adapter: DC 9V 2A
☆Noise ratio : ≥90DB
☆Distortion: THD ≤ 1%
☆Support digital audio output of the TV : SPDIF/Coaxial connection
☆Support Udisk music format: MP3 /WAV –
☆Wireless transmission distance: 10M (due to environmental factors and
wireless devices vary)
☆Conforms to the Wireless V5.0 agreement
User manual*1 Remote control*1
Coaxial cable*1 Power adapter*1 3.5mm AUX cable*1
BT
AUX
OPT
COAX
CARD
USB
S
O
UN
D
B
A
R-
S
1
6
L
us
e
r ma
nu
a
l
52
COAX USB AUX DC-9V
Udisk
In the boot state, when inserted the Udisk, the speaker will automatically converted
to USB mode, and with a prompt tone, the music will be played automatically after
2 seconds, short press “+ -” button to volume adjustment, long press "+ - " button
to the preview/next songs.
NOTE: the Udisk must have Mp3 audio files or WAV format files .
In the boot state, the external devices (such as mobile phones, computers/MP3
and other audio output devices) with the 3.5mm audio cable connected to the
speaker, this time the speaker will automatically switch to the AUX input mode,
there will be a tone, then the speaker can play the audio from the device.
Sleep/Wake
Silent
Volume up
Volume down
Previous song
Play/pause
Next song
Udisk mode
AUX input mode
No function
Coaxial digital audio
input mode
Please put in two AAA
batterys before use
Wireless mode
BT
AUX
OPT
COAX
CARD
USB
NOTE1.short press “+ -” button to volume adjustment, long press "+ - "
button to the preview/next songs.
2. If the USB or AUX ports are not plugged into the device, pressing the“M”
key will not switch to this mode.
NOTE:
1.Without disconnecting the power, the speaker will remember the mode
before the last shutdown when it is turned on next time.
2.In COAX/AUX modes, the“ / ”button has no function, press“ ”
button is the mute function.
DC IN A UX COAX H DMI ARC U SB
DC IN A UX COAX H DMI ARC U SB
Audio output from Mobile Phones
Audio output from TV or Other Devices
Line o ut