Home Theater Projector with BT INSTRUCTION MANUAL MODEL NO.
Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that product heat. 9.
Additional Warnings and Precautions 1. Do not look directly into the projector light. 2. Don’t touch the project lens 3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5.
FCC Warning This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - P1 Additional Warnings and Precautions - - - - - - - - - - - - - - - - - - - - - P2 FCC Warning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 In The Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 Table of Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P4 Remove & Close the Lens Cover - - - - - -
Remove & Close The Lens Cover Remove the lens cover before using Close the lens cover when unit is not using Placing of Your Projector Your projector can be installed in four different configurations (see picture below): Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability. Rear Table: Select this location with the projector placed near the floor behind the screen.
A projector mount is required to install the projector in a ceiling. A special rear projection screen is required. To reduce Image Distortion Move the projector as close to the center of the screen as possible. The light beam from the projector should be perpendicular to the screen for a rectangular or square image. Distance Between The Projector And Screen Measure the distance between the projector and where you want to position the screen. This is the projection distance. Distance 1.16m 1.35m 1.
Adjust The Vertical Location Follow below picture to adjust the vertical location. Adjust The Focus And Keystone Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center.
Controls of Remote Install / Remove Batteries of Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover. NOTES: Batteries shall not be exposed to excessive heat such as placing under the sunlight or near a fire. Please make sure the batteries are installed with their correct polarities.
Controls of Projector 1 LENS 11 Buttons 2 ANGEL ADJ. Knob 12 Buttons 3 AC IN Socket 13 Button 4 FOCUS ADJ. Knob 14 Audio out Jack 5 TRAPEZOIDAL ADJ.
Install Power Adapter Follow below picture to connect power cable Connect small end of cable FIRST. Plug the AC plug to power outlet. WARNING: Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus. Main Button Operation - Press the button to switch on unit, press again to turn off. / SOURCE - Press the button to select input source. / MENU - Press the button to enter projector menu.
- Press to mute the audio. Press again to resume. Connect HDMI Show The Image On Projector Screen Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. 1. Turn off the unit before connect HDMI cable. 2. After connection, press the button to turn on unit and power indicator will light GREEN 3. Press the / SOURCE button to select HDMI 1 or HDMI 2 and the video from the connected device will be shown on projector screen. 4.
Connect VGA Show The Image On Projector Screen Follow below picture to connect VGA cable and device. 1. Turn off the unit before connect VGA cable. 2. Press the button to turn off power of your projector before connection. 3. After connect, press the GREEN 4. Press the / SOURCE button to select VGA mode and the video of VGA device will show on projector screen 5. Press the button to turn on unit and power indicator will light button to turn off unit power.
XGA 1024x768 46.9 40.3 48.4 56.5 75 50 60 70 NOTE: In order to get the sound from the unit, please connect AV IN cable when you connect VGA input. Connect Audio Output ( Aux Out / Line Out / Earphones) Follow below picture to connect audio cable and device. 1. Press the button to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4.
Using TF Card And USB Playback DMP (Media Player) Install USB / TF device: 1. Turn off the unit before install USB / TF card. 2. Install the USB device into USB port. 3. After connect, press the button to turn on unit and the power indicator light GREEN. 4. Press the mode. / SOURCE button to enter and use 5. After selection, use press the buttons to search the PHOTO / MUSIC / MOVIE icon and button to enter.
2. function screen show on lower (figure 3). Use the button to select icon and press the button to play special function. Using Bluetooth Playback Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices. Bluetooth Connection 1. Press the button to turn on unit and the power indicator light GREEN. 2.
Multi-screen interactive connection for phone and projector First, ensure the projector and the mobile is connected to the same wireless network Follow below steps to set up. Support Screen Mirroring Settings (IOS mobile) 1. Press the / SOURCE button to enter and use buttons to select the Screen Mirroring mode. 2. Click the Wi-Fi menu to search and select “RKcast-XXXXXX” (XXXXXX is numbers and letters. It show on the “Screen Mirroring” page) on the mobile device and enter Pin “12345678” to connect 3.
settings 4. Click to select “RKcast-XXXXXX” (XXXXXX is numbers and letters. It show on the “Screen Mirroring” page) on the mobile settings. The mobile device contents will mirror on the projector screen Android Mirroring Settings (DLNA mode) 1. Press the / SOURCE button to enter and use buttons to select the Air Play mode. 2. Click the Wi-Fi menu to search and select “RKcast-19A1EF” on the mobile device and enter Pin “12345678” to connect 3. After connect, click the browser and input “192.168.49.
Using Projector Menu 1 Press / MENU button to enter projector menu, press PICTURE menu. buttons to select This Picture menu showed on right upper of view screen. Use to select different picture effect to Medium / Soft / User / Vidid. Use or to select Contrast / Brightness / Color / Sharpness digit If chose User item. Follow below figure. Use to select different color temperature to Cool / Medium / Warm / User. Use or to select Red / Green / Blue digit If chose User item. Follow below figure.
Aspect Ratio AV mode HDMI mode VGA mode DMP (USB/TF Card) mode Air Play mode PC Setting (Active in VGA mode) Customer define Parameter (Press Horizon Pos. 0-100 Vertical Pos. 0-100 Size 0-100 Phase 0-100 Auto, 4:3, 16:9, Zoom1 ,Zoom2, Panorama Auto, 4:3, 16:9, Zoom1, Zoom2, Just Scan, Panorama, Point To Point Auto, 4:3, 16:9, Point To Point Auto, 4:3, 16:9 to set) Noted: PC setting menu is activated Auto, 4:3, 16:9, Zoom1, Zoom2, Just Scan, Panorama, Point To Point in VGA mode only.
Duration time Off / 5S / 10S / 15S / 20S / 25S / 30S. Press buttons repeatedly to select Front / Rear Ceiling / Front Ceiling / Rear For service center use only. Specifications Bluetooth Version 4.2 Light Source Type LED HDMI Input Supported 1080p , 1080i , 720p, 576i , 480p, and 480i Video Resolution.
user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.