AN-CPL70A Plus Cell Phone Signal Booster User Manual 1 / 12
Introduction With the popularity of mobile communications, people want to make a call anytime, anywhere, so the coverage requirement of communication network is higher and higher, but the reality is not so, sometimes mobile phone signal is not very good, you want to make a smooth call, even in some places cell phone cannot dial out. in this cases, cell phone signal booster can solve this problem in a certain extent.
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
LED Booster working conditions Indicator LED LIGHT Continuous GREEN @normal; Twinkly GREEN @input signals may be not enough; Continuous YELLOW @ stronger input signals, AGC is working; Twinkly YELLOW@ self–oscillation happen ,AGC is working. Continuous RED@ power supply is shut down; Twinkly RED@ self–oscillation happen but power supply is NOT shut down. ②Power supply jack: The booster uses a power input range of DC 5-12V.
Name Indoor Antenna Rubber Antenna Model Gain/Loss PTE-RB-800-2100 3dbi @698-746MHz photo 3dbi @824-894MHz 3.5dbi 1850-1990MHz Ceiling Antenna PTE-CI-800-2500 3dbi @698-746MHz 3dbi @824-894MHz 4.5dbi 1850-1990MHz Indoor Panel PTE-PN-800-2500 Antenna 7dbi @698-746MHz 7dbi @824-894MHz 8.5dbi 1850-1990MHz Outdoor Antenna YAgi Antenna PTE-YG-800/1900 8dbi @698-746MHz 8dbi @824-894MHz 10dbi 1850-1990MHz LPDA Antenna PTE-LO-700-2500 9dbi @698-746MHz 9dbi @824-894MHz 10.
The booster’s main function is to improve weak RF signals of an area. A simple formula: Input power+ Gain= Output power. The signal strength from the outdoor antenna directly affects the efficiency of the indoor coverage. It is very important to choose the outdoor antenna location in order to get the best signals.
so please adjust the outdoor antenna direction to have balance between signals of different mobile operators or various mobile systems. Connect the outdoor antenna to the booster connector marked OUTDOOR with 10 meters 3D-FB Coaxial cable with N male connector Important : Outdoor antenna installation ---Notes: In order to avoid interference, please note that the outdoor antenna should be far away from the following objects of metal, high-voltage line, RF antenna and high-voltage transformer.
other barriers can be used in between to increase isolation. Fix the donor antenna after selecting the best position, and adjust slightly its height or angles in order to get the signals with suitable input power level and calling quality. (2)Installation of Indoor Antenna Proper antennas shall be selected according to the site conditions and the requirement. Omni antenna (Indoor ceiling omni antenna or whip antenna), is suitable to be installed in the center and radiate all directions.
Problem Resolution LED is not light 1.Find an alternate power adaptor and try again. 2.Check the power outlet, the power adapter plug maybe is poor connected. 3.If the problem is still not solved, please contact our company support at support@ANNTLENT.com Booster has no 1. Check whether the direction of the booster is worng connected. 2. Make a call to your mobile phone operator to determine if the frequency band is correct. 3.
A subscriber must have the consent of a wireless provider to operate a Consumer Signal Booster. Subscribers may obtain provider consent in a variety of ways. For example, AT&T, Sprint, T–Mobile, and Verizon Wireless have voluntarily committed to allow their subscribers to use properly certificated Consumer Signal Boosters (i.e., boosters that meet the new rules) on their networks.
● AT&T will allow online registration and will inform OET Lab with the weblink when it is ready. ●U.S.Cellular : (http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp). WARRANTY Warranty information applicable to your Booster Warranty Period: 2 year. Type of Warranty Service: Customer Replaceable Unit and Customer Carry-In or Mail-In Service. ANNTLENT Company is not responsible for Shipping Cost. For Warranty service consult the telephone list at www.ANNTLENT-tech.
The term“IC:“ before the certification/registration number only signifies that the Indu stry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada.