AN-CA65 Cell Phone Signal Booster User Manual 1 / 12
Introduction With the popularity of mobile communications, people want to make a call anytime, anywhere, so the coverage requirement of communication network is higher and higher, but the reality is not so, sometimes mobile phone signal is not very good, you want to make a smooth call, even in some places cell phone cannot dial out. in this cases, cell phone signal booster can solve this problem in a certain extent.
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver.
LED Indicator LED LIGHT Booster working conditions Continuous GREEN @normal; Twinkly GREEN @input signals may be not enough; Continuous YELLOW @ stronger input signals, AGC is working; Twinkly YELLOW@ self–oscillation happen ,AGC is working. Continuous RED@ power supply is shut down; Twinkly RED@ self–oscillation happen but power supply is NOT shut down. ②Power supply jack: The booster uses a power input range of DC 5-12V.
Name Indoor Antenna Rubber Antenna Model Gain/Loss PTE-RB-800-210 3dbi 0 @824-894MHz photo 3.5dbi @2110-2155MHz Ceiling Antenna PTE-CI-800-250 3dbi 0 @824-894MHz 4.5dbi @2110-2155MHz Indoor Panel PTE-PN-800-250 7dbi Antenna 0 @824-894MHz 8.5dbi @2110-2155MHz Outdoor Antenna YAgi Antenna PTE-YG-800/190 8dbi 0 @824-894MHz 10dbi @1710-1755MHz LPDA Antenna PTE-LO-700-250 9dbi 0 @824-894MHz 10.
by FCC rules. Please contact FCC for details:1-888-CALL-FCC The antenna, cables, and other accessories of the booster kits shall not be modified without the approval of the ANNTLENT company, otherwise it shall be deemed invalid. INSTALLATION INSTRUCTIONS (1)Installation of Outdoor Antenna The booster’s main function is to improve weak RF signals of an area. A simple formula: Input power+ Gain= Output power. The signal strength from the outdoor antenna directly affects the efficiency of the indoor coverage.
install them only after the signal quality is tested and the self-oscillation is avoided. If the directional antenna is selected, the main directional angle should point to the tower antenna. If the performance is poor due to weak signals or poor phone call quality, please adjust the direction of outdoor antenna or change its position in order to obtain the best calling effect.
If isolation can’t be achieved by the limited distance, the roof of the building or any other barriers can be used in between to increase isolation. Fix the donor antenna after selecting the best position, and adjust slightly its height or angles in order to get the signals with suitable input power level and calling quality. (2)Installation of Indoor Antenna Proper antennas shall be selected according to the site conditions and the requirement.
(3)Booster Installation Do not place the equipment in direct sunlight or in an area that has abrupt temperature and humidity changes . it is suggested that the booster is installed in a cool,dry and ventilated room without erosive gas and smoke. Connect power adaptor to the booster,connect The other end of power adaptor to the power outlet. WARNING: The input voltage for the booster is 5~12V DC. DO NOT use this Booster with a regular power supply that NOT 5~12V DC .
make a call During using your Booster, if the Booster interferes with your radio or other electronic device, move the Booster further away from those devices, you might be able to solve it yourself. If necessary,please contact your local dealer or send e-mail to our support team by the following methods: E-mail: support@ANNTLENT-tech.com If you want to know about ANNTLENT Company and products for more information, please visit at: www.ANNTLENT.
individual providers. Alternatively, a provider may specify a testing protocol that if satisfied would result in licensee consent to specific booster models. A subscriber may also seek a licensee’s express consent to operate a signal booster, e.g., by phone call or e-mail The following selected information about wireless providers’ Consumer Booster registration mechanisms supplements the requirements and information,and the FCC Signal Boosters website (http://wireless.fcc.gov/signal-boosters/).
reseller informs you. This warranty does not cover the following: Failure resulting from misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by you; The warranty is voided by removal or alteration of identification labels on the Machine or its parts. IC Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).