Product Manual

ManualsBrandsShelterLogic ManualsAccessories22 ft. x 24 ft. x 12 ft. Green Peak Run-In Shelter

22x24x12 Peak Style Run-in Shed

05-58542-0A 08/24/07

PAGE 1

150 Callendar Road

Watertown, CT 06795

ATTENTION:

BOLTS ARE NOT

NEEDED OR

INCLUDED FOR EVERY

CONNECTION BUT

MAY BE

PURCHASED BY CALLING

THE NUMBER BELOW.

FOR MISSING OR

REPLACEMENT PARTS

OR QUESTIONS

PLEASE CONTACT

CUSTOMER SERVICE:

1.800.524.9970

BASIC HAND TOOLS

REQUIRED FOR ASSEMBLY:

• Adjustable Wrench

• Rubber Mallet

Model #

58542

Please read instructions completely before assembly

Description Part # Qty.

Cross Rail Plain Ends

45"L

11105

11068

Cross Rail Swedged 48 1/2”L 11103

11101

Corner Upright Leg

11016 4

Side Bend Tube 11013 12

End Top Bend 11136 2

Middle Top Bend 11135 4

Extension 59.4"L 24

Straight Leg Tube

Cross Rail Swedged

38”L

50 1/2”L

11019

11102

Wind Brace 30”L 11095

Wind Brace 54.2”L 11093 4

Description Part # Qty.

Cross Rail Plain End 46.6"L

11104

Cross Rail Plain End 48.5"L

All-Weather Cover 1A7134 1

Protective Boot 800196 4

4-Way Cover Rail Clamp

3-Way Cover Rail Clamp

11107

11106 8

5/16"x 4" Round Head Bolt

5/16"x 4" Bolt

5/16"x 2 3/4" Bolt

5/16"x 2 1/4" Bolt

5/16"x 2" Bolt

5/16" Nuts

11133 4

11132 8

11131 60

11130 20

11270 8

648 6

690

10040

102

Bolt Cap

11150 24

5/16"x 4 1/2" Bolt

11134 4

Ratchet

Temporary 30”Auger Anchors

Cable - 1’ Lengths

Cable Clamps

822

Base Feet

Summary of content (7 pages)

PAGE 1
22x24x12 Peak Style Run-in Shed Model # 58542 Please read instructions completely before assembly Description Description Part # # Part Qty. Qty. 45"L 11105 10 59.4"L 11068 24 38”L 11019 8 Cross Rail Swedged 50 1/2”L 11102 11 Cross Rail Swedged 48 1/2”L 11103 1 Cross Rail Plain End 46.6"L 11101 1 Cross Rail Plain End 48.
PAGE 2
Basic Frame Assembly STEP 1 Fit together an end rib using the following parts, (1) #11136 3-Way Top Connector, (4) #11068 Swedged Rafter Pole, (2) #11013 Side Bend Tube and (2) #11016 Bend Corner Leg. Using (8) 11131 5/16 X 2 3/4" bolts and (8) 690 5/16" nuts securely fasten the joints of all parts. Lay this rib on the ground at the rear of your shelters designated location. For a 12' tall building be sure to include the two foot extension pipe (4551).
PAGE 3
STEP 4 With help stand the first end rib vertically and lean against a permanent structure such as a tree or a fence. Attach the plain end of a #11102 horizontal tube and a wind brace assembly to the first rib using a #11134 5/16 X 4 1/2" bolt and a #690 5/16" nut on the INSIDE of the bow, on each side bend just above the joint of the side bend/extension. Repeat the same steps on opposite side.
PAGE 4
STEP 7 Install the other end rib as you had installed all the middle ribs only use #11104 crossrails and attach the sliding crossrail using the remaining 3-way coverrail clamps. Note: The final windbrace assemblies should be installed as shown. Be sure the upper of the windbraces are installed between the rib and crossrail Step 8 Installing Top Rail Install the top cross rail assembly starting with #11103 Cross Rail Swedged 48 1/2"L inserted into the End 2-Way Connector.
PAGE 5
STEP 11 INSTALLING AUGER ANCHORS Using a 3/4" pipe or steel rod, (a car tire iron works also) placed through the eyelet on the auger, screw it into the ground. Start at the four corners of the unit and space the remainder out evenly. Be sure to screw the anchor in fully (the eyelet should be a level where it can be securely attached to the frame. Wrap the cable provided through the eyelet of the anchor and around the frame. Secure the cable with the clamp(s) provided.
PAGE 6
STEP 8 Find the open side of the protective boot and open it. Insert the foot of the corner leg into the protective boot. When the foot is all the way in the boot insert the top edge of the boot into the hem of the cover (Fig 13). When complete secure the Velcro on the open side of the boot to close the boot. Fig.
PAGE 7
150 Callender Road Watertown, CT 06795 For Replacement Parts or Help with assembly, Please call: Customer Service: 1-800-524-9970 8am-7pm Mon-Sat EST