User's Manual

ManualsBrandsSheenway Asia ManualsElectronicsdimmer switch with power consumption measurement

45652 Instructions 8/25/2010 10:11:20 AM

Page 1 of 7

45652

Wireless Lighting Control

Energy Monitoring Lamp Dimmer

R Z-Wave

Certified Wireless Lighting Control

Add callouts for Z-Wave

outlet and

Program/Manual control

pushbutton

Thank you for your purchase of a GE Z-Wave

control device. Z-Wave technology is designed to automate

lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave

product family includes a variety of devices to control lighting in your home. It is up to you whether you want to

control one room or your entire house and whether you want to do it all now or start with one room and add more

over time.

This module is one component of a Z-Wave

control system and is designed to work with all other Z-Wave enabled

devices in a home control network. It will also act as a wireless repeater to insure that commands intended for

another device in the network are received, thereby extending the range of the wireless controller. Z-Wave devices

of other types and brands can be added to the system and will also act as range extenders if they support this

function of repeating the signal received to other nodes in the system.

The incandescent lighting plugged into the Z-Wave controlled outlet on this module must not exceed 400 watts. DO

NOT use with fluorescent lighting. Plugging a non-resistive load such as fluorescent lighting or a device with a

motor into the Z-Wave controlled outlet may result in damage to the Lamp Module and will void the warranty.

There are no user serviceable parts in this unit.

To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug

will only fit into a grounding type power outlet. If the plug does not fit into the outlet, contact a qualified electrician to

install the proper outlet. Do not change the plug in any way.

Summary of content (7 pages)

PAGE 1
45652 Instructions 8/25/2010 10:11:20 AM 45652 Wireless Lighting Control Energy Monitoring Lamp Dimmer R Z-Wave® Certified Wireless Lighting Control Add callouts for Z-Wave outlet and Program/Manual control pushbutton Thank you for your purchase of a GE Z-Wave® control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home.
PAGE 2
45652 Instructions 8/25/2010 10:11:20 AM RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS The Load-Sense feature on this Z-Wave product will turn the power to the connected device ON when a change in the load is detected. Z-Wave connected devices should always be unplugged before performing any service or maintenance of the devices. Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances.
PAGE 3
45652 Instructions 8/25/2010 10:11:20 AM Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices Note: The distances shown in the table below are typical examples. Actual performance in your home will vary.
PAGE 4
5652 Instructions 8/25/2010 10:11:20 AM Basic Operation The connected light can be turned ON in three ways: 1. With a remote 2. Manually with the pushbutton on the Z-Wave module 3. By the Load-Sensing feature. Normally, the Z-Wave module controls the ON/Off state of the connected light and power is either turned On or Off at the module (either manually or by the remote).
PAGE 5
45652 Instructions • 8/25/2010 10:11:20 AM It will respond to the ALL ON command but will not respond to the ALL OFF command. Load Sensing Load sensing is disabled when shipped from the factory. This feature can be enabled if desired. Setting parameter 29 to a value of 1 will enable the Load Sense function.
PAGE 6
45652 Instructions 8/25/2010 10:11:20 AM Restoring Factory Defaults All network settings and configuration parameters can all be restored to their factory default settings by using your master controller to delete it from your network. Software Fuse This Lamp Module is designed to protect itself against loads that exceed its maximum power rating. An overload is automatically sensed by the module and all power to the load is shut OFF immediately.
PAGE 7
45652 Instructions 8/25/2010 10:11:20 AM Operation is subject to the following two conditions: • This device may not cause interference • This device must accept any interference, including interference that may cause undesired operation of the device. Important Note: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.