User's Manual

ManualsBrandsSheenway Asia ManualsElectronicsWireless relay

ZB4001(45856)

ZigBee®,In‐WallOn/OffSwitch

HomeAutomationStandardVersion1.2Compliant

Introduction

Thankyouforyourpurcha seofaJascoZigBee®controlleddevice.Jasco’sZigBeelightingcon trols are

designedtoautomate lighting/homecontroland provideeasyremoteoperationofallyourZigBee

enableddevices.TheJascoZigBeeproductfamilyincludesavarietyofdevicestocontrollig htinginyour

home.Itisuptoyouwhetheryouwanttocontroloneroomoryourentirehouseandwhetheryouwant

todoitallnoworstartwithoneroomandaddmoreovertime.

ThedevicecontrolledbytheZigBeeIn‐WallOn/OffSwitchmustnotexceed900watts(Incandescent);

1440W(12A)Resistiveor½HPMotor.

Therearenouserserviceablepartsinthisunit.

!Warning!

RISKOFFIRE

RISKOFELECTRICALSHOCK

RISKOFBURNS

NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT

ZigBee enabled devices should never be used to supply power to or control the On/Off status of medical and/

or life support equipment!

WARNING

ControllingAppliances:

ExerciseextremecautionwhenusingZigBeedevicestocontrolappliances.OperationoftheZigBeedevicemay

beinadifferentroomthanthecontrolledappliance,alsoanunintentionalactivationmayoccurifthewrong

buttononthecontrollerinterfaceispressed.ZigBeedevicesmayautomaticallybepoweredonduetotimed

eventprogramming.Dependingupontheappliance,theseunattendedorunintentionaloperationscouldpossibly

resultinahazardous.

1. DoNotincludeZigBeedevicesinGroupsorScenesiftheycontrolappliances.

2. DoNotuseZigBeedevicestocon

trolelectricheatersoranyotherapplianceswhichmaypresentahazardous

conditionduetounattendedorunintentionalorautomaticpoweroncontrol.

KeyFeatures



TurntheconnecteddeviceOn/OffmanuallyorviatwoZigBeecontroller

 CanbeIncludedinmultipleGroupsandScenes

 MaybeusedinsinglepoleinstallationorwithuptothreeJascoauxiliaryswitches in2‐way,3‐

wayor4‐waywiringconfigurations

Summary of content (8 pages)

PAGE 1
ZB4001 (45856) ZigBee®, In‐Wall On/Off Switch Home Automation Standard Version 1.2 Compliant Introduction Thank you for your purchase of a Jasco ZigBee® controlled device. Jasco’s ZigBee lighting controls are designed to automate lighting/home control and provide easy remote operation of all your ZigBee enabled devices. The Jasco ZigBee product family includes a variety of devices to control lighting in your home.
PAGE 2
        Interchangeable Paddle switch: White & light almond paddle in package Over the Air updates – Once joined to your ZigBee network, the device can transparently receive updates through your ZigBee gateway Energy Monitoring – The device can report wattage (W) and kilowatt hours (kWh).
PAGE 3
CONNECTIONS TWO‐WAY CONTROL SINGLE SWITCH WIRING USING ONE PRIMARY SWITCH THREE‐WAY CONTROL TWO SWITCH WIRING USING ONE PRIMARY AND ONE AUXILIARY SWITCH FOUR‐WAY CONTROL THREE SWITCH WIRING USING ONE PRIMARY AND TWO AUXILIARY SWITCHES Single, Dual and Triple Gang Boxes When installing the In‐Wall On/Off switch in multiple gang boxes it may be necessary to break off one or both of the scored tabs on the front yoke. This does not affect the electrical rating of the switch.
PAGE 4
. Observe Important Wiring Information Important: This switch is rated for and intended to only be used with copper wire. The home’s electrical wires may be attached to the screw terminals or inserted into the holes in the back of the switch enclosure and clamped in place by tightening the screw terminals. Always follow the recommended wire strip lengths when making wiring connections.
PAGE 5
OPTIONAL for THREE or FOUR‐WAY CONTROL: Connect the Traveler wire (usually Red) to the screw terminal marked TRAVELER on the primary switch (Do Not remove the tape over the terminal if you are not using the traveler connection).The other end of this Traveler wire connects to the TRAVELER screw terminal on the Auxiliary Switch. 1. The auxiliary requires the following 3 wiring connections: a. The Traveler wire. This is used to send voltage signals to the primary switch.
PAGE 6
ZigBee Network Pairing Join the switch to the ZigBee Network 1. From your ZigBee Controller’s interface, choose to add lighting device and enter Locating/Pairing mode as instructed by the controller. 2. After applying power to the In‐Wall switch, your In‐Wall Switch will begin auto scan mode as it searches for a controller to pair with Auto‐Scan: LED Status Indicator Blinks 3x every 10 seconds as the device scans for a compatible network controller to pair with until Timeout.
PAGE 7
WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied.
PAGE 8
Compliance with IC Rules and Regulations IC: 6924A‐ZB4001 Jasco Products Company Model: ZB4001 (45856) CAN ICES‐3(B) / NMB‐3(B) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. OPERATING SPECIFICATIONS       Power 120VAC, 60Hz Signal (Frequency) 2.