User's Manual

ManualsBrandsSheenway Asia ManualsElectronicsDuplex Receptacle

45605 Instructions, Revision a.5 4/4/2007 6:58:13 PM

Page 1 of 4

Model: 45605

Z-Wave, RF Controlled, 600W, 120 VAC, Duplex Receptacle

Z-Wave

Add callouts for Z-Wave & Pass Through outlets

Pass-Through

Thank you for your purchase of a GE SmartHome™ Z-Wave

control device. Z-Wave technology is designed to

automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-

Wave product family includes a variety of devices to enable and control lighting in your home. It is up to you whether

you want to control one room or your entire house and whether you want to do it all now or start with one room and

add more over time.

This duplex receptacle is one component of a Z-Wave

control system and is designed to work with all other Z-Wave

enabled devices in a home control network. It will also act as a wireless repeater to insure that commands intended

for another device in the network are received, thereby extending the range of the wireless controller. Z-Wave devices

of other types and brands can be added to the system and will also act as range extenders if they support this function

of repeating the signal received to other nodes in the system.

CAUTION! This device is intended for installation in accordance with the National Electric Code and local regulations

in the United States, or the Canadian Electrical Code and local regulations in Canada. It is recommended that a

qualified electrician perform this installation.

The device plugged into the Z-Wave controlled outlet on this module must not exceed 600 watts (Incandescent); 15

Amps, 1800W (Resistive); or ½ HP (Motor). The maximum rating for both outlets combined is 1800W (15A) Resistive.

There are no user serviceable parts in this unit.

Key Features

• One Z-wave remote controlled AC outlet

o Remote ON/OFF control via the Z-Wave controller/network

o Manual ON/OFF control with the pushbutton

• One Always-ON pass through AC outlet

Installation

This receptacle may be used in new installations or to replace an existing wall receptacle.

Insert Wiring Diagram

Line -- Black wire

Neutral – White wire

Ground – Green wire

Summary of content (4 pages)

PAGE 1
45605 Instructions, Revision a.5 4/4/2007 6:58:13 PM Model: 45605 Z-Wave, RF Controlled, 600W, 120 VAC, Duplex Receptacle R Z-Wave Add callouts for Z-Wave & Pass Through outlets Pass-Through Thank you for your purchase of a GE SmartHome™ Z-Wave® control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE ZWave product family includes a variety of devices to enable and control lighting in your home.
PAGE 2
45605 Instructions, Revision a.5 4/4/2007 6:58:13 PM WARNING! SHOCK HAZARD! Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. 1. 2. 3. 4. 5. Strip 3/4" of insulation from the ends of the conductors and connect as shown in the wiring diagram. Check the connections to be sure they are tight and no bare conductors are exposed.
PAGE 3
45605 Instructions, Revision a.5 4/4/2007 6:58:13 PM Configuration Please note: Not all controllers are capable of this; your controller must be designed to perform this function. The GE model #45601 is designed to do this. Use its “Setup Menu”, “Config Unit” to change the configuration of devices. LED Light When shipped from the factory, the LED on the 45605 is set to turn ON when the connected outlet is turned OFF. To make the LED turn ON when the light is turned ON, change parameter 3’s value to “0”.
PAGE 4
5605 Instructions, Revision a.