ENGLISH SHARPY C61375 INSTRUCTION MANUAL INDEX Page Contents 2 Safety information 12 Unpacking and preparation 13 Installation and start-up 14 Control panel 16 Menu setting 23 Maintenance 30 Optional accessories 31 Technical information 31 Cause and solution of problems 32 Channel functions Congratulations on choosing a Clay Paky product! We thank you for your custom.
SAFETY INFORMATION • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
Not for residential use LiFePO4 Pb • Battery This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. Disposing This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according to the local regulation.
INFORMAZIONI DI SICUREZZA • Installazione Assicurarsi che tutte le parti per il fissaggio del proiettore siano in buona condizione. Assicurarsi della stabilità del punto di ancoraggio prima di posizionare il proiettore. La fune di sicurezza, debitamente agganciata all’apparecchio e fissata alla struttura di sostegno, deve essere installata in modo che, in caso di cedimento del sistema di supporto primario, si abbia la minor caduta possibile dell’apparecchio.
Non adatto all'illuminazione domestica Non per uso residenziale LiFePO4 Pb • Batteria Questo prodotto contiene una batteria ricaricabile piombo-acido o Litio Ferro Tetrafosfato. A tutela dell'ambiente si prega di smaltire la batteria a fine vita in conformità alla normativa vigente. Smaltimento Questo dispositivo è conforme alla Direttiva Europea 2012/19/UE - Rifiuti di apparecchiature elettriche ed elettroniche (RAEE).
CONSIGNES DE SÉCURITÉ • Installation S’assurer que toutes les pièces pour la fixation du projecteur sont en bon état. S’assurer de la stabilité du point d’ancrage avant de positionner le projecteur. Le câble de sécurité, à fixer correctement à l’appareil et à la structure de support, doit être installé de façon à ce que, en cas de rupture du système de support principal, la chute de l’appareil soit la plus limitée possible.
Non adapté à l’éclairage domestique Non indiqué pour un utilization résidentiel LiFePO4 Pb • Batteria Questo prodotto contiene una batteria ricaricabile piombo-acido o Litio Ferro Tetrafosfato. A tutela dell'ambiente si prega di smaltire la batteria a fine vita in conformità alla normativa vigente. Élimination Ce dispositif est conforme à la Directive Européenne 2012/19/UE – Déchets d’équipements électriques et électroniques (DEEE).
INFORMATIONEN ZUR SICHERHEIT • Installation Sicherstellen, dass alle Teile für die Befestigung des Projektors in einwandfreiem Zustand sind. Vor der Installation des Projektors die Stabilität der Verankerungsstelle überprüfen. Das korrekt am Gerät eingehakte und an der Haltestruktur befestigte Sicherheitsseil muss so installiert werden, dass bei einem Nachgeben der Haupthalterung die Fallhöhe des Gerätes so gering wie möglich ist.
Nicht für Haushaltsbeleuchtung geeignet Nicht für den häuslichen Gebrauch LiFePO4 Pb • Batterie Dieses Produkt enthält eine wiederaufladbare Blei-Säure-Batterie oder Lithium-Eisen-tetraphosphat. Zum Schutz der Umwelt bitten wir Sie, diese Batterie, nachdem sie verbraucht ist, gemäß den geltenden Vorschriften zu entsorgen. Entsorgung Diese Vorrichtung entspricht der Europäischen Richtlinie 2012/19/UE - Abfall von elektrischen und elektronischen Gerätschaften (RAEE).
INFORMACIONES DE SEGURIDAD • Instalación Asegúrese de que todos los elementos de fijación del proyector estén en buenas condiciones. Controle la estabilidad del punto de anclaje antes de instalar el proyector. La cuerda de seguridad, correctamente enganchada al aparato y fijada a la estructura de soporte, debe colocarse de modo que, si el soporte principal cede, el aparato sufra la menor caída posible. En caso de desgaste de la cuerda de seguridad, sustitúyala por el recambio original.
No es apropiado para la iluminación doméstica No para uso residencial LiFePO4 Pb • Batería Este producto contiene una batería recargable plomo-ácido o de litio tetrafosfato Hierro. Para proteger el ambiente se ruega eliminar la batería conforme a la normativa vigente. Eliminación Este dispositivo es conforme a la Directiva Europea 2012/19/UE - Residuos de equipos eléctricos y electrónicos (RAEE).
UNPACKING AND PREPARATION 1 Lamp 189W (fitted into projector) IST005/001 2 x 183102/805 Packing contents - Fig. 1 2 3 PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig.
INSTALLATION AND START-UP 4 Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
CONTROL PANEL 6 Mains L N Connecting to the mains supply - Fig. 6 7 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 DMX 512 3 PIN SIGNAL 2 SCREEN 1 3 SIGNAL Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
9 28 28 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.
MENU SETTING 1 2 Set Up Dmx Address 3 Option Lamp Dmx Information Safety Black Out Channel Mode Pan / Tilt Fixture ID System Errors Fixture Hours Invert Pan Lamp Hours Invert Tilt Ethernet Interface Lamp Strikes Swap Pan-Tilt Encoder Pan-Tilt Option System Version P/T Homing Mode Information Board Diagnostic Pan Home Def Pos Manual Control Dmx Monitor Tilt Home Def Pos Test Color Fans Monitor Fixed Wheel Shortcut Linear Movement Advanced Shutter Sensor status Shutter On Error
NOTE: On grey the default options Set Up Dmx Address SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing Allows you to select the DMX ADDRESS. 1) Press - the current DMX Adress appear on the display. 2) Use the UP and DOWN , RIGHT keys to plan the DMX Address. 3) Press to confirm the selection or LEFT to keep current settings. Address xxx F B C E D F Channel Mode CHANNEL MODE Allows you to select a channel arrangement from the two available.
OPTIONS MENU On Option Lamp Dmx Off LAMP DMX Used for enabling lamp remote control channel. - the current settings appear on the display (On or Off). 1) Press 2) Use the UP and DOWN keys to enable (On) or disable (Off) the lamp remote control channel. 3) Press to confirm the selection or LEFT to keep current settings. F B C F Safety Black Out D SAFETY BLACK OUT This allows the Dimmer's automatic lock option to be activated after 3 seconds with no incoming DMX signal.
F 1) Press , the current setting appears on the display. 2) Use the UP and DOWN keys to select one of the following settings: 0% 12.5% 25% 50% (default) 75% 87.5% 100% 3) Press to confirm the selection or LEFT to keep the current setting. B C F Color Fixwheel Shortcut D COLOR Fixed wheel short-cut Used for optimizing color change time so that the disc turns in the direction that requires shorter movement. 1) Press – the current settings appear on the display (On or Off).
Option Used for restoring default values on all options menu items and relevant submenus. 1) Press , a confirmation message (Are you sure?) appears on the display. 2) Select YES to confirm the selction or NO to keep current setting.
Information System Version Board Diagnost. Board CPU brd com.dev 0: PT-3f 1: 8-Ch Revis. x.x.x x.x x.x x.x Hw.rv. x.x x.x x.x SYSTEM VERSION Used for displaying the software and hardware version of each board installed in the projector. CPU brd (CPU board) 0: PT-3f (Pan / Tilt board) 1: 8-Ch (8 channel board) Board 0:PT-3f 1:8-Ch Status Good Good Err% 0.00 0.
TEST MENU Test TEST Allows you to check the proper functioning of effects. to return to the top menu level. 1) Press and DOWN keys to select the required test. 2) Use the UP to confirm the selection or LEFT to keep current settings.
MAINTENANCE 10 11 2 1 1 1/4 Turn 2 1/4 Turn 3 4 Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11.
13 12 1 Upper Side Upper Side 2 1 2 1/4 Turn Upper Side Upper Side 4 3 14 5 Upper Side Upper Side 6 Opening and closing lamp compartment - Fig. 12 Lamp change - Fig 13 Take the new lamp out of its package and insert in the fitting. WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth. Lamp regulation - Fig. 14 To centre the lamp, turn the adjusting screw as shown in the figure.
15 This position is correct. In the event of fault, manually bend the metallic support. DIM003/001 6° 6° 2 2 Lower Side 1 Anti IR/UV filter support template - Fig. 15 WARNING: During maintenance and lamp replacement, we recommend you pay close attention to correct anti IR/UV filter support tilt. Incorrect tilt compromises lamp performance. 16 2 Lower Side 1 Replacing fixed gobos wheel - Fig. 16 WARNING: Before using personalised gobos wheel contact Clay Paky.
17 Lower Side Lower Side Upper Side Upper Side Periodical cleaning - Fig. 17 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
18 1 2 3 Upper Side Extraction of the effect modules: Preliminary operations - Fig.
19 2 Lower Side Lower Side 1 4 Lower Side Lower Side 3 Extraction of the effect modules - Fig. 19 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 17 and 18 in reverse order.
20 2 1 3 7 5 4 6 Battery removal - Fig. 20 This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.
OPTIONAL ACCESSORIES 21 Lower Side 1 2 C61190 Heat screen filter - Fig. 21 An optional filter kit is also available when the SHARPY projector is used in environments that do not meet the minimum allowed distance of 12 metres from illuminated objects; when this kit is assembled, the projector can be used at a minimum distance of 8 metres from illuminated objects. 22 Lower Side C61190 accessory can be placed inside the projector when not in use - Fig.
TECHNICAL INFORMATION • Resolution: - PAN = 2.11° - PAN FINE = 0.008° - TILT = 0.98° - TILT FINE = 0.004° • Accuracy: - Resolution ± 0,15° (Range 0,3°) Power supplies available 115/230V 50/60Hz Input power: 350VA a 230V 50Hz. Total output Max 8000 lumens 315 (12.40") Lamp: Lamp system with a short arc burner in a reflector Philips MSD Platinum 5R (L10103) - Output Lamp power: 189W - Colour temperature 8000 K - Luminous flux 7950lm - Average life 2000 h - Any working position 280 (11.
CHANNEL FUNCTION NB: To prevent accidental breakage of the effects, which could collide with each other during transport, before switching the projector OFF check that all the projector Channels have been excluded (DMX level = 0 bit).
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit ) all the others channels stay at 0 bit. • COLOUR WHEEL - channel 1 • STATIC GOBO CHANGE - channel 4 255 128 124 120 116 111 107 103 99 94 90 86 82 77 73 69 64 60 56 52 47 43 39 35 30 26 22 18 13 9 5 0 EFFECT FAST ROTATION (160 rpm) MACRO BIT SLOW ROTATION (0.
• EFFECTS MOVEMENT - channel 7 BIT • PAN - channel 10 Operation with option InvertPan Off (Tilt conventionally represented at 14% and option Invert Tilt G EFFECT GOff) 255 BIT 255 0%-100%: 0.33 sec 0 0 • FROST - channel 8 G Operation with option InvertPan On (Tilt conventionally represented at 14% and option Invert Tilt BIT 255 EFFECT GOff) FROST INSERTED BIT 255 0%-100%: 0.
• TILT - channel 12 Operation with option Invert Tilt Off (Pan conventionally represented at 0% and option Invert Pan G • FUNCTION - channel: 14 BIT GOff) EFFECT 255 BIT 255 SE UNUSED RANGE L TX D X E 63 51-62 LINEAR (Default) 38-50 CONVENTIONAL 25-37 NORMAL 12-24 FAST (Default) 128 SEL TX D X E 0-11 DIMMER CURVE FUNCTION PAN-TILT FUNCTION UNUSED RANGE The functions are actived passing through the unused range and staying 5 seconds in necessary level.
TIMING CHANNELS Timing Channel Channel function 17 Pan - Tilt time Pan - Tilt - (Pan fine - Tilt fine) 18 Colour time Colour wheel 19 Beam time Dimmer - Frost - Prism 20 Gobo time Static Gobo TIME TABLE Seconds Full 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6 5.8 6 6.2 6.4 6.6 6.8 7 7.2 7.4 7.6 7.8 8 8.2 8.
See our catalogue for details of these and more Dirty Rigger products Gradav Hire and Sales Ltd The Power House Elstree Film Studios Shenley Road Borehamwood WD6 1JG Phone 020 8324 2100 FAX 020 8324 2933 email office@gradav.co.uk Web www.gradav.co.