Operating Instructions

OPERATING INSTRUCTIONS
The car requires 1 “AAA” 1.5V battery (not included). Use a
Phillips head or Cross screwdriver to loosen the screw
securing the corresponding battery cover plate. Insert the
batterie(s), ensuring the correct polarity per the diagrams
below. Replace the battery cover and tighten the screw.
ii iiii
The remote requires 2 “AAA” 1.5V batteries (not included).
Use tool to press the fastener and release the battery door
for the remote.
iiiiii
Carefully remove items from package.
BATTERY WARNING:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable batteries.
• Alkaline batteries are recommended. Use only the
specified voltage.
• Insert batteries using the correct polarity. Always use,
replace, and recharge (if applicable) batteries under
adult supervision.
• Do not charge with non-rechargeable batteries.
• Do not short-circuit the battery supply terminals.
• Do not dispose of batteries in a fire, batteries may
explode or leak.
• Remove batteries before storing.
• Recycle or dispose of batteries according to federal,
state, and local laws.
• Keep these instructions for future reference.
• For indoor use only. Avoid water when operating.
• Do not submerge car or controller in water.
• Do not use people or animals as obstacles
• Do not run car into furniture objects or hard surfaces as this
will cause damage to both the objects and car.
• Keep fingers, hair and loose clothing away from the tires, gears
and motor while car is switched to “ON”.
• Do not leave car or transmitter near sources of heat or under
direct sunlight for long periods of time.
• Remove all batteries when not in use to avoid accidental operation.
• Adult supervision is recommended when operating car.
• Thoroughly inspect products before every use. If the product
appears worn, frayed/splintered, cracked, or broken in any
manner, discontinue use and discard immediately.
Reverse
Forward
Turn Left
Turn Right
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAFETY PRECAUTIONS
The artwork and design of this manual are protected by US copyright law and
may not be reproduced, distributed, displaced, published or used for any purpose
without prior written permission. Altering, removing or reproducing any of the
trademark or copyright notices on this package is not permitted.
©2019 MerchSource, LLC. Irvine, CA 92618. All rights reserved.
Printed in China
WARNING:
CHOKING HAZARD - Small parts.
Not for children under 3 years.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the pictures on the manual may
dier slightly from the actual product.
1-800-374-2744
FOR TECHNICAL SUPPORT,
PLEASE CALL
6+
Status
LED
Power
On/O
Switch
Press the power button on the remote. The LED at the top of
the remote will turn ON.
ii iiii
Slide the power switch on the underside of the car to the
ON position.
RC MINATURE
RACER