XV-Z10000 XV-Z10000 PROJECTOR PROJECTEUR PROYECTOR PROJETOR OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO SHARP CORPORATION Printed in Japan Imprimé au Japon Impreso en Japón Impresso no Japão TINS-A440WJZZA ENGLISH ............. -1 – -92 FRANÇAIS ........... -1 – -91 ESPAÑOL ............ -1 – -90 PORTUGUÊS ......
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. Dette udstyr overholder kravene i direktiv nr.
Before using the projector, please read this operation manual carefully. Introduction Introduction ENGLISH IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 14. Model No.: XV-Z10000 Serial No.
INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications.
Outstanding Features Introduction 1. High Color Purity and Broad Dynamic Range Due to Advanced Optical Engine • Newly developed 12° DMD™ chip provides significantly improved optical efficiency and excellent contrast ratio. • Newly developed DDR (Double Data Rate) chip eliminates Color Breaking phenomena common with previous generation DLP™ projectors. • Superior image quality with Minolta™ optical lens system. • Use of 270 W high-output lamp realizes both high color purity and high brightness.
Contents Introduction Outstanding Features ......................................... 3 Contents ............................................................... 4 IMPORTANT SAFEGUARDS ............................... 6 How to Access the PDF Operation Manuals of SharpVision Manager ......................................... 9 Part Names ........................................................ 10 Projector (Front and Top View) ................................ 10 Projector (Rear View) ............................
Selecting the Picture Display Mode ................ Switchable High Contrast/High Brightness Mode ......................................... Digital Shift Function ........................................ Subtitle Setting .................................................. Video Digital Noise Reduction (DNR) System .............................................. Displaying the Lamp Usage Time .................... Setting On-screen Display ............................... Selecting the Signal Type ..............
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save them for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
Introduction 19. Replacement Parts 18. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions.
IMPORTANT SAFEGUARDS Be sure to read the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Authorized SharpVision Service Center or Dealer for replacement. See “Replacing the Lamp” on pages 76-78.
Introduction How to Access the PDF Operation Manuals of SharpVision Manager PDF operation manuals in several languages for the “SharpVision Manager” theater projector software provided are included in the CD-ROM. To utilize these manuals, you need Adobe Acrobat Reader installed on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can install it from the CD-ROM. To install Acrobat Reader from the CD-ROM For Windows: 1 Insert the CD-ROM in the CD-ROM drive.
Part Names Numbers in refer to the main pages in this operation manual where the topic is explained. Projector (Front and Top View) Adjustment buttons (", ', \, |) 32 32 For displaying adjustment and setting screens. For selecting menu items. ENTER button 32 For setting items selected or adjusted on the menu. UNDO button MENU button 58 RESIZE button For switching the screen size (SIDE BAR, SMART STRETCH, etc.).
17 18 23 Terminals for component and RGB signals. INPUT 5 terminal For controlling projector using a computer. 19 DC 12V OUTPUT terminal Terminal for DVI digital, computer RGB and component signals. INPUT 2 terminals RS-232C terminal 24 WIRED REMOTE control input terminal 17 INPUT 4 terminal 18 Terminals for component and RGB signals. AC socket For connecting video equipment.
Part Names Remote Control (Front View) 32 KEYSTONE button For turning the power on or off. 36 For adjusting Keystone Correction or Vertical Size setting. ENTER button Power (ON/OFF) buttons 32 MENU button For displaying adjustment and setting screens. 32 For setting items selected or adjusted on the menu. 32 Adjustment buttons (', ", \, |) For selecting menu items. UNDO button 37 For undoing an operation or returning to the default settings.
Using the Remote Control Introduction Available Range of the Remote Control ■ The remote control can be used to control the projector within the ranges shown in the illustration. Remote control 23'(7 m) Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material. 45˚ 30˚ 30˚ When using the remote control: • Be sure not to drop, expose to moisture or high temperature.
Accessories Supplied accessories Remote control RRMCGA128WJSA Lens cap (attached) PCAPH1056CESA Two “AA” size batteries CD-ROM (SharpVision Manager) UDSKAA028WJN1 Power cord CACCDA010DE01 Terminal cover CCOVA1985CE02 Operation manual (this manual) TINS-A440WJZZA SharpVision Manager operation manual TINS-A452WJZZ Optional accessories 3 RCA to 15-pin D-sub cable (9'10'' (3.0m)) DVI to 15-pin D-sub adaptor (7.9'' (20cm)) DVI cable (9'10'' (3.0m)) RS-232C cable (32'10'' (10.
Connections and Setup Connections and Setup
Connecting the Projector to Other Devices Before Connecting Note • Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connections are made. • Be sure to read the operation manuals of the devices to be connected before making connections.
Connecting to Video Equipment Connecting to Video Equipment Using an S-video or a Composite Video Cable VCR or other video equipment To S-video output terminal To video output terminal Connections and Setup Using an S-video or a composite video cable, a VCR, laser disc player or other video equipment can be connected to INPUT 3 and INPUT 4 input terminals. Connect the projector to the video equipment using an S-video cable or a composite video cable (both commercially available).
Connecting the Projector to Other Devices To analog component output terminal Connecting to Component Video Equipment Using a Component Cable (INPUT 1 or 2) Use a component cable when connecting the component video equipment such as DVD players and DTV* decoders to INPUT 1 or 2 terminal. * DTV is the umbrella term used to describe the new digital television system in the United States.
Connecting to Component Video Equipment Using a 3 RCA to 15-pin D-Sub Cable and the DVI to 15-pin D-Sub adaptor (INPUT 5) Optional accessories DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20 cm)) DVI to 15-pin D-sub adaptor (sold separately) To analog component output terminal Connections and Setup Use a 3 RCA to 15-pin D-Sub cable and the DVI to 15-pin D-Sub adaptor when connecting to the INPUT 5 terminal, component video equipment such as DVD players and DTV* decoders.
Connecting the Projector to Other Devices Connecting to Video Equipment with the DVI Output Terminal Using the DVI Cable Optional accessory DVD player or DTV* decoder Use the DVI cable when connecting to the INPUT 5 terminal, video equipment with the DVI output terminal such as DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television system in the United States. Connect the projector to the video equipment using the DVI cable.
Connecting the Projector to a Computer Connecting to a Computer Using the DVI to 15-pin D-sub Adaptor and the RGB Cable DVI to 15-pin D-sub adaptor Type: AN-A1DV (7.9" (20cm)) DVI to 15-pin D-sub adaptor (sold separately) Notebook computer Connections and Setup Connect the projector to the computer using the DVI to 15-pin D-sub adaptor and the RGB cable. Optional accessory To RGB output terminal • Secure the connectors by tightening the thumbscrews.
Connecting the Projector to Other Devices DVI cable Type:AN-C3DV (9'10'' (3.0m)) Optional accessory Connecting to a Computer Using a DVI Cable (Sold Separately) To DVI Digital output terminal Desktop computer Connect the projector to the computer using the DVI cable. Note • Switch the signal type to either “A.RGB” or “D.PC RGB” depending on whether the computer output signal is analog or digital. See page 65.
Controlling the Projector by a Computer Controlling the Projector Using an RS-232C Cable To RS-232C terminal Connections and Setup When the RS-232C terminal on the projector is connected to a computer with an RS-232C cable (null modem, cross type, sold separately), the computer can be used to control the projector and check the status of the projector. See page 80 for details. RS-232C cable Optional accessory Type: AN-C10RS (32'10'' (10.
Connecting the Projector to Other Devices Using as a Wired Remote Control Connecting the Remote Control to the Projector WIRED REMOTE control input terminal When the remote control cannot be used due to the range or positioning of the projector (rear projection, etc.), connect a ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNW4870CEZZ) from the WIRED R/C JACK on the top of the remote control to the WIRED REMOTE control input terminal. To WIRED R/C JACK ø3.
Setup Using the Adjustment Feet 1 2 Press the foot releases and lift the projector to the desired angle. Connections and Setup The height of the projector can be adjusted using the adjustment feet when the projector is placed on an uneven surface or when the screen is slanted. The position of the projected image can be made higher by adjusting the projector when it is in a location lower than the screen. Foot releases Remove your hands from the foot releases.
Setup Focus ring Zoom knob Adjusting the Lens The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector. 1 Zooming is adjusted by moving the zoom knob. Zoo m in ut mo Zoo Zoom Knob 2 The focus is adjusted by rotating the focus ring.
Using the Lens Shift The height of the projected image can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the projector. Lens shift dial Up n Dow Note Connections and Setup • Do not turn the lens shift dial beyond the upper limit and lower limit positions. This may cause the projector to malfunction.
Setup Setting up the Screen Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult. • For optimal image, position the screen so that it is not in direct sunlight or room light.
Screen Size and Projection Distance x y 4 3 : Screen area : Picture area Screen size (4:3) Diag. (x) 250" 200" 150" 100" 84" 72" 60" Width 200" 160" 120" 80" 67" 58" 48" Height 150" 120" 90" 60" 50" 43" 36" Projection distance (y) Maximum (y1) 41'4" (12.6 m) 33' (10.1 m) 24'9" (7.5 m) 16'5" (5.0 m) 13'9" (4.2 m) 11'10" (3.6 m) 9'10" (3.0 m) Minimum (y2) 30'6" (9.3 m) 24'4" (7.4 m) 18'3" (5.6 m) 12'1" (3.7 m) 10'2" (3.1 m) 8'8" (2.6 m) 7'2" (2.
Setup Projecting a Reversed/Inverted Image Projection from behind the screen ■ Place a translucent screen between the projector and the audience. ■ Reverse the image by setting “Rear” for “PRJ Mode” in the “Options” menu. See page 69 for use of this function. Projection using a mirror ■ Place a mirror (normal flat type) in front of the lens. ■ Reverse the image by setting “Rear” for “PRJ Mode” in the “Options” menu, when the mirror is placed on the audience side. See page 69 for use of this function.
Basic Operation Basic Operation
Image Projection Basic Procedure Power indicator Connect the required external equipment to the projector before operating the following procedures. Lamp replacement indicator Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 34. 1 Plug the power cord into the wall outlet.
"On-screen Display (Example) Press , , , or on the remote control or on the projector to select the INPUT mode. • After pressing once on the projector, use to select the desired input mode.
Image Projection 4 Press or on the remote control on the projector, then or again while the press confirmation message is displayed, to turn off the projector. Note • If you accidentally pressed and do not want to turn off the power, wait until the confirmation message disappears. Info • Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to the rise in internal temperature, as the cooling fan also stops.
3 Press ' or " to select the desired language, and then press . 4 Press . • The desired language will be set as the on-screen display.
Keystone Correction and Vertical Size Adjustment Correcting Trapezoidal Distortion and Adjusting the Vertical Size of the Picture KEYSTONE button ENTER button ', ", \, | buttons UNDO button This function allows for Keystone (On-screen Trapezoidal Distortion) Correction and the adjustment of the vertical size of the picture. Note • When the image is projected either from top or from bottom toward the screen at an angle, the image becomes distorted trapezoidally.
3 When adjusting vertical size, again displays pressing the vertical size adjustment menu. 4 Press "and ' to adjust the vertical size of the picture, and press . • See below for details about the vertical size screen. Ajuste de Tamanho Vertical A razão parente da tela poderá variar quando a função de deslocamento da lente é usada em combinação com a função Correção Trapezoidal. Neste caso, ajuste a razão aparente usando o ajuste de tamanho vertical.
Menu Bar Items This list shows the items that can be set in the projector.
■ INPUT 3 / 4 Mode Main menu Picture Page 44 Sub menu Main menu Sub menu Options Digi. Shift –30 +30 Page 62 Subtitle –30 +30 Contrast –30 +30 Bright –30 +30 Color –30 +30 Reset DNR Tint –30 +30 Sharp –30 +30 CLR Temp 5500 11500 Normal Level A Level B Gamma Position Standard Black Detail Brighten Custom 1 Custom 2 SVM Gamma Video System Auto PAL (50/60Hz) SECAM NTSC4.43 NTSC3.
Using the Menu Screen This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following procedure. Menu screen for INPUT 1, INPUT 2 or INPUT 5 RGB mode Menu screen for INPUT 3, INPUT 4 or INPUT 5 VIDEO Mode Menu Bar (Main Menu) Menu Selections (Adjustments) 1 Press Menu Bar (Main Menu) ", ', \, | buttons ENTER button MENU button . • The menu screen is displayed.
2 Press \ or | to select the menu you want to adjust. Note • For details on the menus, see the tree charts on pages 38 and 39. 3 Press " or ' to select the item you want to adjust. Note • To display a single adjustment item, press after selecting the item. Only the menu bar and the selected adjustment item will be displayed. Then if you press " or ', the following item (“Bright” after “Contrast”) will be displayed. • Press Basic Operation | to return to the previous screen.
Using the Menu Screen Menu Selections (Settings) 1 Press " , ', \, | buttons ENTER button MENU button . • The menu screen is displayed. Note • The “Picture” menu screen for the selected input mode is displayed. • The on-screen displays shown on the lower right are displayed when INPUT 1, 2 or 5 mode is selected while RGB signals are input. 2 Press \ or | to select the menu you want to adjust.
4 Press |. • The cursor shifts to the sub menu. Press " or ' to select the setting of the item displayed in the sub menu. 6 Press Basic Operation 5 Sub menu . • The item selected is set. Note • Some adjustment items will display a confirmation message. When setting an item, press \ or | to select “Yes” or “OK” and then press . to select “ON” or “OFF” for • Use the item of “Economy Mode”. 7 Press . • The menu will disappear.
Adjusting the Picture You can adjust the projector’s picture to your preferences with the following picture settings. Adjusting Image Preferences Note • First select “INPUT # Memory” when you want to save the “Picture” menu settings. See page 47 for details. Adjust the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.
Emphasizing the Contrast This function emphasizes the bright portions of images to obtain a higher contrast image. Select “White Emphasis” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • ON Emphasizes the bright portions of images. • OFF Disables “White Emphasis”. Basic Operation Selecting the Gamma Position This function allows you to select the desired gamma position. Select “Gamma Position” in the “Picture” menu on the menu screen.
Adjusting the Picture Progressive Mode This function allows you to select the progressive display of a video signal. The progressive display projects a smoother video image. Select “Progressive Mode” in the “Picture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • 2D Progressive This function is useful to display fastmoving images such as sports and action films. This mode optimizes the image in a displayed frame.
Picture Setting Function This function stores all items set in “Picture”. Five settings can be stored separately in “Memory 1” to “Memory 5”. Each stored setting is reassigned to each input mode (INPUT 1 to INPUT 5). Even when the input mode or signal is changed, you can easily select optimal settings from the stored settings. ■ When Saving: Select “Memory #” or “INPUT # Memory” before setting on the “Picture” menu. Select “Picture Setting” in the “Picture” menu on the menu screen.
Adjusting the Gamma Use this function to select the gamma position and adjust the gamma curve for finer image adjustment. Selecting the Gamma Position Select “Gamma Position” in the “Gamma” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item Standard Black Detail Brighten Custom 1–2 SVM Gamma Description For Standard picture. Gives greater depth to darker portions of image. Brightens darker portions of image. Allows you to adjust the gamma curve for each of RGB.
Adjusting the Gamma Adjust the gamma curve to suit your preferences. These gamma values can be adjusted only when the gamma position is set to “Custom 1” or “Custom 2”. Select the gamma item in the “Gamma” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected Item Description \ button | button For adjusting the display characteristic of red color For giving greater depth to brighter For giving greater depth to darker portion of image in red color.
Color Management System (C. M. S.) This function allows you to individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) . Selecting the Color Reproduction Mode Select “Color Selected” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item Standard Custom 1-3 Description Sharp default setting “Lightness”, “Chroma” and “Hue” can be adjusted for each of the six colors.
Setting the Brightness of the Target Color Select “Lightness” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Setting the Chromatic Value of the Target Color Basic Operation Select “Chroma” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Setting the Hue of the Target Color Select “Hue” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.
Color Management System (C.M.S.) Resetting User-Defined Color Settings Select “Reset (This Color)” or “Reset (All Colors)” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item Reset (This Color) Reset (All Colors) Description “Lightness”, “Chroma” and “Hue” of the color selected for “Target” are reset. “Lightness”, “Chroma” and “Hue” of all colors are reset. Overview of All Color Settings Select “View Settings” in the “C.M.S.” menu on the menu screen.
Adjusting Computer Images Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. When Auto Sync is OFF When “Auto Sync” is “OFF”, interference such as flickering or vertical stripes may occur if displaying tilings or vertical stripes. Should this occur, adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for obtaining an optimum image.
Adjusting Computer Images Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select “Select Setting” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • If a memory position has not been set, a resolution and frequency setting will not be displayed. • When selecting a stored adjustment setting with “Select Setting”, you can set the projector in the stored adjustments.
Checking the Input Signal This function allows you to check the current input signal information. Select “Signal Info” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Auto Sync Adjustment Used to automatically adjust a computer image. Select “Auto Sync” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.
Adjusting Computer Images Auto Sync Display Function Used to set the screen displayed during Auto Sync. Select “Auto Sync Disp” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item -56 Description The image set as a background image is projected. The computer image being adjusted is displayed.
Easy to Use Functions Easy to Use Functions
Selecting the Picture Display Mode This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “SIDE BAR”, “SMART STRETCH”, “CINEMA ZOOM”, “STRETCH”, “NORMAL” or “DOT BY DOT” image. Switching the Picture Display Using Different Input Signals Press RESIZE button . • Each time is pressed, the display changes as shown on pages 59 and 60.
VIDEO For 4:3 aspect ratio For 16:9 aspect ratio SIDE BAR SMART STRETCH CINEMA ZOOM STRETCH DOT BY DOT 480I 480P 576I 576P NTSC PAL SECAM 960 ⳯ 720 1280 ⳯ 720 1280 ⳯ 720 1280 ⳯ 720 – 480P 960 ⳯ 720 1280 ⳯ 720 1280 ⳯ 720 1280 ⳯ 720 – 720P – – – 1280 ⳯ 720 1280 ⳯ 720 1080I – – – 1280 ⳯ 720 – • Select “DOT BY DOT” during 720P input when viewing 720P output from a computer. • 720P switches between “STRETCH” and “DOT BY DOT”. “STRETCH” is fixed when 1080I signal is entered.
Selecting the Picture Display Mode COMPUTER SVGA (800 ⳯ 600) For 4:3 aspect ratio For without 4:3 aspect ratio NORMAL DOT BY DOT 960 ⳯ 720 800 ⳯ 600 XGA (1024 ⳯ 768) 960 ⳯ 720 1024 ⳯ 720 SXGA (1280 ⳯ 960) 960 ⳯ 720 1280 ⳯ 720 SXGA (1280 ⳯ 1024) 900 ⳯ 720 1280 ⳯ 720 • “NORMAL” is fixed when XGA (1024 × 768) signals are entered.
Switchable High Contrast/High Brightness Mode This function controls the quantity of the projected light and the contrast of the image. It can be operated using the HIGH CONTRAST/HIGH BRIGHTNESS MODE button on the projector. Set “HIGH BRIGHTNESS MODE” when the projector is used in a relatively bright room. Operating the Theater Mode Function Press the HIGH CONTRAST/HIGH BRIGHTNESS MODE button to select the “HIGH CONTRAST MODE” or “HIGH BRIGHTNESS MODE”.
Digital Shift Function For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television system in the United States. Adjusting the Digital Shift Select “Digi. Shift” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • The Digital Shift Function works with the SMART STRETCH and CINEMA ZOOM screen.
Video Digital Noise Reduction (DNR) System Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise. Reducing Image Noise Select “DNR” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • Set a level so as to view a clearer picture. Make sure to set DNR to “OFF” in the following cases: • When the image is blurry. • When the contours and colors of moving images drag.
Setting On-screen Display This function allows you to turn on or off the on-screen messages. When setting “ Level A” or “ Level B” in “OSD Display”, the input mode display (e.g. INPUT 1) will not appear, even if the INPUT button is pressed. Turning Off the On-screen Display Select “OSD Display” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected Item -64 Description Normal All On-screen Displays are displayed.
Selecting the Signal Type This function allows you to select the input signal type RGB or Component for INPUT 1 and 2, or Digital PC RGB, Digital PC Component, Digital Video RGB, Digital Video Component, Analog RGB or Analog Component for INPUT 5. Selecting the Signal Type For INPUT 1 and INPUT 2 Select “Signal Type” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note For INPUT 1 and INPUT 2 Set when RGB signals are received from video equipment.
Setting the Video System The video input system mode is preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal. Setting the Video System Select “Video System” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • The video signal can only be set in INPUT 3 or INPUT 4 mode.
Selecting the Economy Mode These functions allow you to reduce the power consumption of the projector. Setting the Power Save Select “Power Save” in “Economy Mode” under the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • Although noise is reduced when “Power Save” is set to “ON”, brightness decreases by 20%. • “Power Save” mode is factory preset to “OFF”. • “Power Save” is switched on and off by pressing .
Selecting the Economy Mode Automatic Power Off Function When no input signal is detected for more than 15 minutes, the projector will automatically turn off if set to “ON”. The Auto Power Off function will be disabled when it is set to “OFF”. Select “Auto Power Off” in “Economy Mode” under the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note • When the Auto Power Off function is set to “ON”, 5 minutes before the power turns off, the message “Power OFF in X min.
Reversing/Inverting Projected Images This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications. Setting the Projection Mode Select “PRJ Mode” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43.
Displaying the Adjustment Settings This function can be used to display all the adjusted settings as a list on the screen. Overview of All Menu Settings Select the “Status” menu on the menu screen and press . ➝For operating the menu screen, see pages 40 to 43.
Appendix Appendix
Maintenance Cleaning the projector Cleaning the lens ■ Be sure to unplug the power cord before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items on the projector for long time. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Cleaning the Ventilative Holes • This projector is equipped with ventilative holes to ensure the optimal operating condition of the projector. • Periodically clean the ventilative hole by vacuuming it off with a vacuum cleaner. • The ventilative holes should be cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location.
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below.
Info • If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.) • If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may be triggered, preventing the power from going on.
Regarding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative hours of use or when you notice a significant deterioration in the picture and color quality. The lamp usage time can be checked with “Lamp Timer” in the “Options” menu on the menu screen. ■ For lamp replacement, please consult your nearest Authorized SharpVision Service Center or Dealer.
Removing and Installing the Lamp Unit Info • Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened). • Please refer to the installation manual included with the lamp unit.
Regarding the Lamp 4 Remove the lamp unit. 5 Insert the new lamp unit. 6 Attach the lamp unit cover. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. • Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then tighten the user service screws.
Connecting Pin Assignments DVI-I (INPUT 5 / DIGITAL INPUT) port : 29 pin connector • DVI Digital INPUT C3 C5 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 24 23 • • • ~ • • • 18 17 C4 C2 C1 16 8 7• • • • • ~ • • • • • 2 1 ••••••••• ~ ••••••••• 9 • DVI Analog RGB Input Pin No.
(RS-232C) Specifications and Command Settings PC control A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, commercially available) to the projector. (See page 23 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard.
COMMAND PARAMETER RETURN COMMAND PARAMETER RETURN INPUT 5 WHITE ENPHASIS : OFF R C W E _ _ _ 0 OK OR ERR POWER OFF P O W R _ _ _ 0 OK OR ERR INPUT 5 WHITE ENPHASIS : ON R C W E _ _ _ 1 OK OR ERR KEYSTONE (–127 – +127) K E Y S * * * * OK OR ERR INPUT 5 PICTURE SETTING : INPUT 5 MEMORY R C P S _ _ _ 0 OK OR ERR V-SIZE (–10 – +10) V S I Z _ _ * * OK OR ERR INPUT 5 PICTURE SETTING : MEMORY 1 R C P S _ _ _ 1 OK OR ERR INPUT 1 I R G B _ _ _ 1 OK OR ERR INPUT 5 PICTURE SETTING : MEMORY 2 R C P
(RS-232C) Specifications and Command Settings CONTROL CONTENTS INPUT 3 GAMMA POSITION : CUSTOM 2 COMMAND PARAMETER RETURN CONTROL CONTENTS G M V B _ _ _ 4 OK OR ERR RGB INPUT DISPLAY RGB ADJUSTMENT RESET I A R E _ _ _ 1 OK OR ERR INPUT 4 GAMMA POSITION : STANDARD SAVE SETTING (1 – 7) M E M S _ _ _ * OK OR ERR SELECT SETTING (1 – 7) M E M L _ _ _ * OK OR ERR RGB HORIZONTAL FREQUENCY CHECK T F R Q _ _ _ 1 kHz (***.
Wired Remote Control Terminal Specifications Specifications of wired remote control input • ø3.5 mm minijack • External: GND • Internal: +3.
Computer Compatibility Chart Computer • Multiple signal support Horizontal Frequency: 15–81 kHz, Vertical Frequency: 43–100 Hz, Pixel Clock: 12–120 MHz • Compatible with sync on green and composite sync signals • SXGA compatible in advanced intelligent compression • AICS (Advanced Intelligent Compression and Expansion System) resizing technology The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Troubleshooting Problem No picture and no sound or projector does not start. Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables incorrectly connected to rear panel of the projector. • Remote control batteries have run out. • External output has not been set when connecting notebook computer. • The cover of the lamp unit is not installed correctly. • The selected “Signal Type” is wrong.
Troubleshooting Problem Check Picture is green on • Change the input signal type setting. INPUT 1 or 2 COMPONENT. Picture is pink (no green) on INPUT 1 or 2 RGB. • The lamp replacement indicator is blinking in red. Replace the Picture is dark. lamp. Picture is too bright and • Picture adjustments are incorrectly set. whitish.
Specifications This SHARP projector uses a DMD Chip. This very sophisticated panel contains 921,600 pixels. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Dimensions Units: inches (mm) Top View Side View 15 49/50 (406) Side View Rear View 7 (178) Front View 18 11/16 (475) Bottom View -88
Glossary Advanced intelligent compression High quality resizing of lower and higher resolution images to fit the projector’s native resolution. Aspect Ratio Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9. Auto Sync Optimizes projected computer images by automatically adjusting certain characteristics. Background Initial setting image projected when no signal is being output.
Index 2D Progressive .................................................... 46 3D Progressive .................................................... 46 AC socket ............................................................ 16 Adjusting Computer Images ................................ 53 Adjusting the Lens ............................................... 26 Adjusting the Picture ............................................ 44 Adjustment buttons .............................................. 32 Adjustment feet ...
VALID IN USA ONLY CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
VALID IN CANADA ONLY LIMITED WARRANTY Consumer Electronics Products Congratulations on your purchase! Sharp Electronics of Canada Ltd. (hereinafter called Sharp ) gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer: Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship.
XV-Z10000 XV-Z10000 PROJECTOR PROJECTEUR PROYECTOR PROJETOR OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO SHARP CORPORATION Printed in Japan Imprimé au Japon Impreso en Japón Impresso no Japão TINS-A440WJZZA ENGLISH ............. -1 – -92 FRANÇAIS ........... -1 – -91 ESPAÑOL ............ -1 – -90 PORTUGUÊS ......
