VL-NZ50U/NZ100U VL-NZ150U SERVICE MANUAL S22F9VL-NZ50U SERVICE MANUAL LIQUID CRYSTAL DIGITAL CAMCORDER MODELS NTSC VL-NZ50U VL-NZ100U VL-NZ150U LIQUID CRYSTAL DIGITAL CAMCORDER In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS NTSC MODELS VL-NZ50U/NZ100U/NZ150U Page 1. IMPORTANT SERVICE NOTES ..........................................................
VL-NZ50U/NZ100U VL-NZ150U 1. IMPORTANT SERVICE NOTES connections, metal cabinet, screw heads, knobs and control shafts, etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug (a non polarized adaptor plug must be used but only for the purpose of completing these checks) on the set and repeat the AC voltage measurements for each exposed metallic part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.
VL-NZ50U/NZ100U VL-NZ150U WARNING :TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO WET LOCATIONS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol mark means following. Camcorder only For continued protection against fire hazard, replace only with same type fuse. (CP1; 1A 24V, CP2; 1A 24V) CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER·SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
VL-NZ50U/NZ100U VL-NZ150U CAUTION BEFORE BATTERY DESTROY NICKEL-CADMIUM BATTERY The following program is available in the United States. Please consult local environmental authorities concerning the availability of this or other programs in your area. The RBRCTM Seal SHARP participates in the RBRCTM* Nickel-Cadmium Battery Recycling Program in the United States.
VL-NZ50U/NZ100U VL-NZ150U ■ PRECAUTIONS FOR USING LEAD-FREE SOLDER 1) Employing lead-free solder "Main PWB", "Camera head PWB", "Audio I/O PWB", "Card PWB", "Inverter PWB", "Operation PWB", "DC Jack PWB", "CCD PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
VL-NZ50U/NZ100U VL-NZ150U 2.
VL-NZ50U/NZ100U VL-NZ150U 3. PART NAMES For details on the use of each control.
VL-NZ50U/NZ100U VL-NZ150U 4. DISASSEMBLY OF THE SET Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery have been removed. 1. 3. (c) (c) (c) (c) LCD Panel (c) FPC (h) (h) (c) (i) (c) Battery Unit Radiation Angle 1) Remove the 1 screw ((i)XiPSF17P03000) and 2 screws ((h)XiPSF17P02000). 2) Remove the 2 screws ((c)XiPSN17P03000) to detach the VCR operation PWB. Then remove the FPC of the LCD panel and FPC of the reflector to detach the LCD panel.
VL-NZ50U/NZ100U VL-NZ150U 5. 7. (i) (c) Microphone Cover Camera Front Cabinet (c) (o) (i) (i) Mechanism (i) NZ100U/NZ150U NZ50U (i) (i) (i) (k) (c) (k) (h) (c) (k) Camera Rear Cabinet Camera Rear Cabinet (c) 1) Remove the 3 screws ((c)XiPSN17P03000), 4 screws ((i)XiPSF17P03000) and 1 screw ((h)XiPSF17P02000) (NZ50U only) fixing the camera rear cabinet to detach it. (Note: When detaching the camera rear cabinet, pay attention to the FPC of the camera operation unit.
VL-NZ50U/NZ100U VL-NZ150U 5. MECHANISM ADJUSTMENT JIGS AND PARTS 5-1. Mechanism check adjustment jigs 1. PB-use cassette Torque meter 2. 9DASD-1015 3. DB * 1mN·m/1.5mN·m 1. Torque gauge 2. JiGTG0045 3. CN * For use in VS-REW winding torque measurement. 1. Torque gauge head 2. 9EQTGH-DH5000 3. BW * For use with the torque gauge listed left. 1. Tension gauge 4N 2. JiGSG0400 3. BK * For measurement of pinch roller pressure. Configuration 1. Name 2. Part No. 3.
VL-NZ50U/NZ100U VL-NZ150U 6. INSPECTION AND MAINTENANCE ITEMS AND INTERVALS In order to keep the mechanical section always in good condition, perform the following inspection and maintenance at regular intervals. In addition, after repair, perform the following maintenance items regardless of how long the user has been using the unit. 6-1.
VL-NZ50U/NZ100U VL-NZ150U 7. MECHANICAL ADJUSTMENTS AND CHECKS The items discussed here relate to general on-site servicing (field servicing). Adjustments and replacements that require sophisticated facilities, jigs and technology are omitted.
VL-NZ50U/NZ100U VL-NZ150U 7-4. Back tension torque check and adjustment in record (playback) mode AC adapter used, with cassette controller assembly (1) Checking Set the torque cassette (SD-1015), and make sure in the SP record mode that the supply side torque is within the standard shown below (or in the playback mode for the tape on which the signal has been SP-recorded). (If torque ripple exists, read its center value.) 0.7 ± 0.1mN·m (2) Adjustment (Fig.
VL-NZ50U/NZ100U VL-NZ150U (If the tension fluctuates, read its center value.) 15 ± 12mN 7-8. Checking of winding Tu reel base ratchet torque DC3V, without cassette controller assembly (Independent Mechanism) (1) Remove the cassette controller assembly, then apply DC3V to the loading motor and put the system into standby mode. (refer to 9-1) (2) Move the swing arm toward the S reel base side. Be careful not to cause damage to the gears and other parts in the process. (Fig.
VL-NZ50U/NZ100U VL-NZ150U 8. TAPE RUNNING ADJUSTMENT 8-1. Adjustment locations · T roller, arm · Tu guide, arm · Slide chassis Adjust the height of only replaced parts with the adjusting jig. Adjustment procedure 8-2 · S guide · Pole base · Guide roller · Drum assembly · Capstan motor, etc.
VL-NZ50U/NZ100U VL-NZ150U 8-4. Running rough adjustment (With cassette controller) 1) Su, Tu guide roller height adjustment Entrance side NG (1) Loosen the guide roller lock screw, then tighten loosely so that the roller turns easily. (2) Replay an alignment tape, and adjust the Sup, Tu guide roller so that the envelope sides of entrance and exit are flat. (3) Perform ± 1/4 shift, then, as in the above case, adjust until the envelope becomes flat.
VL-NZ50U/NZ100U VL-NZ150U 9. MECHANICAL SECTION ASSEMBLY AND PARTS REPLACEMENT (DISASSEMBLY AND REASSEMBLY) Mechanical section disassembly and reassembly are explained in this section. For removal of the cabinet, etc., refer to 4. DISASSEMBLY OF THE SET. 1. Always replace cut washers that have been removed, for example in parts replacement, with new ones. 2. When reassembling, be careful not to allow screws, washers or foreign matter to enter. They can cause mechanical misoperation. 3.
VL-NZ50U/NZ100U VL-NZ150U (6) STOP mode (5) PLAYBACK (RECORD, FF, VSF) mode The system is in the STOP (Rec Lock in CAMERA mode) The mechanism position for playback, record, FF and fast position; the S and the T pole bases are snap-fitted to the drum feed playback. base, the S brake is in contact with the S reel base, and the Tu The pinch roller is pressed to the capstan shaft, and the S/Tu brake is in contact with the Tu reel base. main brake is separated from the S/Tu reel base.
VL-NZ50U/NZ100U VL-NZ150U 9-3. How to operate with the circuit board without the cassette controller assembly. In this method, if the procedure is followed incorrectly there is danger of damaging the mechanism and the tape, so except in special cases, such as when measuring the VSR torque, do not perform this procedure. Normally operate this unit with the cassette controller assembly attached. Be sure to follow each caution mentioned. (1) Apply DC3 ~ 4V to the loading motor to enter the standby mode.
VL-NZ50U/NZ100U VL-NZ150U 9-5. Reassembly 9-5-1. Reassembly in side of the main chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the main chassis). 1. Groove grease 4.
VL-NZ50U/NZ100U VL-NZ150U 9-5-2. Reassembly in side of the Slide chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the slide chassis) 2. 1. Sensor FPC cover Grease 391 H 393 F Tu main brake 374 N T spring hanging ANG 356 S guide hexagon 428 nut Tu reel base Ass'y 375 N O 411 Fit the main brake SPR from above, and close with the hook.
VL-NZ50U/NZ100U VL-NZ150U 9-5-3. Main chassis assembly and slide chassis assembly assembling method (1) Enter the coupling mode. (In this position, the cam groove of the T arm operation lever in the figure is parallel to the side of the main chassis, and the poll base is slightly moved.
VL-NZ50U/NZ100U VL-NZ150U GREASE/OIL APPLICATION From rear surface side Rear surface · groove side surface Front surface · rear surface · groove side surface Drum base assembly From rear surface side Main cam Loading lever Tu loading arm S loading arm Intermediate gear angle Enabled after assembling Including groove side surface Enabled after assembling O : Oiling(Cosmo Hydro HV22) G : Greasing(Moly Coat YM-103) : Greasing(Moly Coat YM-103) Pinch control lever Capstan FPC stopper T arm contro
VL-NZ50U/NZ100U VL-NZ150U 10. ADJUSTING THE ELECTRICAL CIRCUITS Before starting the electric circuit adjustment • The adjustment methods described herein are used, in most cases, when the expendable mechanical parts, including the video head, have been replaced, at which time the electrical circuits need to be readjusted. Before adjusting the electrical circuits, make sure that the mechanism works properly (i.e., the mechanism is properly adjusted).
SPEAKER VSP0020P-918N QSW-ZA003WJZZ ZOOM OPERATION SW UNIT QSW-ZA004WJZZ POWER/SNAP SW UNIT SC2701 12 16 LENS UNIT LENS FPC Direct connection 15 14 13 CCD PWB TURN SW UNIT QSW-Z0376TAZZ 17 QPWBHB194WJZZ SC21 SC551 18 QCNW-2060TAZZ 19 CAM HEAD PWB SC101 10 SC1502 AUDIO I/O PWB SC2601 9 SC1202 8 MAIN PWB SC3301 P306 SC900 SC701 2 1 QCNW-1832TAZZ HEAD AMP UNIT HEAD AMP FPC CPWBH2876TA01 SC1204 SC2801 21 QCNW-A392WJZZ P2900 DC Jack PWB CPWBHB195WJ01(NZ100U/NZ150U) CPW
VL-NZ50U/NZ100U VL-NZ150U [TEST POINT] (Wiring board diagram: Main Side A) TL2801(C OUT) COMMON PULSE C2800 C2830 R2819 R2811 Q2806 Q2907 R3495 R443 R2807 IC2803 R3492 R3493 Q2805 R2912 C3462 TL919 TL2905 TL2907 TL2906 TL997 TL906 TL905 TL904 Q2902 VA1402 L923 D2904 Q911 C992 R951 R950 R7415 TL1478 R2911 R7413 R7419 R414 C974 L917 R2919 L915 D7401 R7416 C424 Q7402 Q7403 R996 R990 C973 Q907 R5704 FB408 C477 C478 TL406 TL403 TL417 C5704 C5703 C3709 L901 R95
VL-NZ50U/NZ100U VL-NZ150U (Wiring board diagram: AIO Side B) TL608 EE level check TL609 Frequency character check EE level check Frequency character check TL609 TL608 TL2687 TL607(GND) EE level check Frequency character check R624 0 TL2689 TL2645 R632 TL2653 TL2663 C636 C633 C629 R627 C624 R623 C628 TL2683 TL2688 R628 R619 C617 R641 TL2680 R631 C631 C620 TL607 C637 C634 C627 R630 C622 R625 R629 TL2643 R620 R614 R609 R617 C619 TL2648 C613 TL2644 C609 TL2692(INT MIC L) EE
VL-NZ50U/NZ100U VL-NZ150U [Making adjustments] Adjusting the servo system controller and related parts 1. Setting the system codes Replacement of IC705 E2PROM requires the following data to be set in this order. [Procedure] Set the unit to the VCR mode and set the data for each address. Code 1. Model code 2. Destination code Address 01 09 02 0A Data NZ150U 07 F8 01 FE NZ100U/C 04 FB NZ100K 04 FB NZ50U/C 00 FF NZ50K 00 FF 3.
VL-NZ50U/NZ100U VL-NZ150U 3. SHUT OFF adjustment Mode Procedure Examples VCR ADJ mode 1) Load a recordable tape, and set the camera mode. (Set TL911 to GND or SW901 to ON.) 2) Press the "CONTINUE" and then the "TEST SEL" on the remote control for adjustment to enter the TEST mode (T-01 blinks). 3) Select T-03 with the FF or REW key and then press the PB key. 4) Observing the power voltage from TL2905(-), set it so that TL904(+) obtains 5.95V ± 50mV. 5) Press the MENU button on the main unit.
VL-NZ50U/NZ100U VL-NZ150U ADJUSTING THE VIDEO I/O CIRCUIT SYSTEM (Wiring board diagram: Main Side A) R2915 C2901 R1480 TL2905 R2910 R2860 R2857 R2858 R913 R2914 FB2801 C2903 TL901 TL2907 TL902 TL900 TL903 C901 D2908 TL2906 R2908 R2909 TL997 P901 D2902 R2918 CP2 R2902 TL906 R2904 R2901 D2901 R2903 R1483 C2902 VA1402 TL1479 C990 TL1470 TL1471 TL2903 TL2901 R2917 D2903 Q2904 TL2902 Q2901 C930 R2905 R2907 D2905 TL905 TL904 Q2902 CP1 TL2904 R2906 Q2905
VL-NZ50U/NZ100U VL-NZ150U ADJUSTING THE LCD CIRCUIT * To make this adjustment, set the backlight switch to the "NORMAL" position.
VL-NZ50U/NZ100U VL-NZ150U 4. COM-BIAS adjustment Test point Mode Procedure Adjustment rating Remark Examples LCD panel display surface Address VCR ADJ 33 VCR AV input 1) Set the data of the address 582 to AF. 2) Set up the illuminance meter (TOPCON IM-3) on the LCD panel surface. (The outside light must not enter.) 3) Minimize the ripple of the output waveform of the illuminance meter. 4) Return the data of the address 582 to the initial value. (Initial value: 40) Minimum Response time : 0.
VL-NZ50U/NZ100U VL-NZ150U ADJUSTING THE MIC AMP CIRCUIT (Wiring board diagram: AIO Side B) TL608 EE level check TL609 Frequency character check EE level check Frequency character check TL609 TL608 TL2687 TL607(GND) EE level check Frequency character check TL2689 TL2645 R632 C636 C633 C629 R627 C624 R623 R619 C628 TL2644 R613 C610 TL2691 R642 C612 TL2692 TL2667 TL2642 TL2646 C614 R643 IC601 C642 C616 C615 R640 TL2675 R612 C2610 TL2673 TL605 TL2686 TL606 TL2671 C2611 TL2674
VL-NZ50U/NZ100U VL-NZ150U DV INTERFACE (IEEE1394) ID SETTING This unit has a DV interface function conforming to IEEE1394. Therefore, each individual ID number must be used for each unit. Since this ID is written on the E2PROM (IC302) on the head amp PWB, the ID must be newly written when replacing this IC or the head amp PWB. Address 180, 17F, 17E Mode VCR Adjustment rating ID number obtained from the URL below Procedure 1) Refer to the ID code application below.
VL-NZ50U/NZ100U VL-NZ150U (5) Click on [Repair use]. Click (6) Input the necessary information for the application. For the indispensable input items, be sure to input them. Select the [Group/company] and [Kind name] from the list. Input the [Model name]. Input the [Serial number]. Input the [Site/department of repair]. (7) Click on [motion]. The confirmation screen will appear. (8) Click on [Yes]. 2. Print the application result. (1) Print out the application result screen.
VL-NZ50U/NZ100U VL-NZ150U 10-2. Camera Section Adjustments 10-2-1. Camera section service (1) Camera adjustment is performed after the set has been completed. (2) Subjects, measuring instruments and jigs needed for camera section service and adjustments • • • • • • Gray scale chart Color bar chart Oscilloscope Digital voltmeter Halogen lamp: 2 pcs.
VL-NZ50U/NZ100U VL-NZ150U 4) Operation flow FF or REW PLAY FF or REW PLAY STOP Address is selected and specified, with the data called. Then the called data are selected and fixed. The operation flows in this sequence. 5) When the adjustment is complete: Press the "CONTINUE" key to let the "CAM ADJ" display disappear from the screen.
VL-NZ50U/NZ100U VL-NZ150U (4) Camera signal system adjustment mode In the camera signal system adjustment mode, the automatic white balance is disabled to allow for the adjustment of the camera unit. At this time, the white balance mode is fixed at the INDOORS mode and the focus mode is switched to the manual focus mode. 1) Shifting to the camera signal system adjustment mode Set the data for the address "0000" to " 00". ] This shifts the camera signal system adjustment mode.
VL-NZ50U/NZ100U VL-NZ150U 10-2-4. Adjustment procedures Adjustment method Item (1) Auto-focus adjustment Set the unit to the auto-focus function adjustment mode and write data to the address "0000" one after another. This executed the adjustments automatically. The items to be adjusted are as listed below. Every time an adjustment is made properly, the data "FF" is written to the address.
VL-NZ50U/NZ100U VL-NZ150U Adjustment method Item (4) Iris AE coarse adjustment (1) Video output is observed with the oscilloscope in the grey scale standard record state, • Measurement terminal: the data of address "0002" is rewritten, and the luminance signal level is adjusted white S terminal luminance signal output to 720 ± 10mVp-p.
VL-NZ50U/NZ100U VL-NZ150U Adjustment method Item (7) White balance adjustment(3200K) • Measurement terminal: EE output • Address: "0090" INDOOR_W/B R "0092" INDOOR_W/B R • Measuring instrument: Vector scope • Object: Grey scale • Data variation width: "0000" to "03FF" (1) White balance adjustment is performed repeatedly.
VL-NZ50U/NZ100U VL-NZ150U 11. USEFUL TIPS (PROBLEMS DIFFER FROM THOSE FOUND ON VHS OR 8MM DECKS BECAUSE THE SIGNALS ARE DIGITALLY PROCESSED.) Camera (EE mode) Picture fails to appear Camera (REC mode) VCR (PB mode) VCR (EE mode) Picture fails to appear when tape recorded on this unit or another unit is played back. (EE OK) Blueback fails to appear.
VL-NZ50U/NZ100U VL-NZ150U 12. SIGNAL FLOW DIAGRAMS 12-1.
VL-NZ50U/NZ100U VL-NZ150U WAVEFORM DIAGRAM (DURING COLOR BAR PLAYBACK) 12-3.
VL-NZ50U/NZ100U VL-NZ150U 12-5. FLOW IN PB MODE (AUDIO) WAVEFORM DIAGRAM (1.
USB IC51 D/A-CON IC101 CDS/AGC REC (EE) PB IC552 IRIS DRIVE 27.000MHz IC22 TG IC21 V-Driver IC1 460K CCD-Sensor SD/MMC CARD IC5701 USB/CARD_CTL IC151 10bit A/D Video out IC1401 ANALOG VIDEO I/O IC201 16Mbit SDRAM CameraZoom IC202 CAMERA ENGINE (Total ASIC) CAM DSP IC701 MECHA/SYSTEM MiCON IC703 CHARACTER GENERATOR IC3702 16Mbit SDRAM PPW v1 OSD Synthesis IC3701 CAMERA/CARD MiCON M-CTL ZOOM LCD CTL PPW LCD IC4401 VIO ENGINE (Total ASIC) CODEC CLK. Gen CT INT.
IC21 V-Driver VHiUPD16510-1 20P OFD V1, V2, V3, V4 H1-CLK, H2-CLK, RS-CLK IC1 CCD-Sensor VHLLZ24E31+-1 V1, V2, V3, V4, VH1, VH2, SUB IC22 TG VHiLR38650/-1 48P FSX, FCDX, BCPX, PBLK, XRS 47 CAM-HEAD X21 27.
J1401 CAMERA SECTION BLOCK DIAGRAM CAM ENGINE 48 VIDEO IN/OUT VIDEO-IN IC1431 INPUT SW VHiMM1503XN-1 6P ZYP0 7 ZCP0 7 ZUVSELP ZCLKP ZHDP ZVDP IC1401 VIDEO I/O VHiMM1510XN-1 6P A-YC-OUT A-Y/COMP-V-IN IC4401 VIO ENGINE RH-iXA149WJZZ 303P CDY0 7, CDC0 7 REC (EE), PB PB REC (EE) R OUT G OUT B OUT CLD, SPD, CTR EX1, EX2,SPS, RES, CLS, LOW PSS1 CVDR, CHDR I/O SEL SC2801 VR, VG, VB IC2800 LCD INTERFACE VHiMM1323XV-1 24P IC452 REC/PB ENGINE RH-iX0809TAZZ 368P CDVDP CDHDP CDUVSELP VL-NZ50U/N
DI00 49 REC (EE), PB PB REC (EE) 15 11 7 7 XCS, XWE, XRAS, XCAS, XUDQM, XLDQM, XCKE, CLK18M1IV SM-ADR0 CVDR CHDR I/OSEL CDUVSELP CDHDP, CDVDP IC407 Codec External Memory 16M SDRAM RH-iXA166WJZZ 60P IC4401 VIO ENGINE RH-iXA149WJZZ 303P CDY0 CDC0 IC452 REC/PB ENGINE RH-iX0809TAZZ 368P X401 24.
REC (EE), PB PB REC (EE) REC/PB ENGINE BLOCK DODAT PDAD PDDA ADMCLK ADBCK ADLRCK DFSO DFSI AIDAT CS-1394, RD-1394, WR-1394 TPA-, TPA , TPB-, TPB AUD R AD IN AUD L AD IN AUD R DA OUT AUD L DA OUT IC1602 16Bit ADC/DAC VHiPCM3008+-1 16P MECHA/SYSTEM MICON DV CONNECT IC601 AIO VHiBH7761KV-1 48P INT MIC SP OUT AUDIO R I/O AUDIO L I/O SPEAKER AV JACK VL-NZ50U/NZ100U VL-NZ150U 13-5.
IC1 CCD Sensor 51 Focus-Motor Driver Zoom-Motor Driver IC551 Iris Drive IC552 Iris Amp IC21 V-Driver IC101 CDS AGC IC22 Timing Generator CCD IC51 D/A Converter X21 27MHz CAMERA HEAD IC3701 CAM/CARD µ-com IC151 10bit A/D-COnverter SSG Digital Auto C-Process Y-Process CAM ENG IC3702 16M SDRAM Electric Zoom Image Stabilizer Digital Noise Reduction IC202 Sirial Data PB Y/C Data 16M SDRAM IC201 REC /PB Y/C Data MAIN VL-NZ50U/NZ100U VL-NZ150U 13-6.
VL-NZ50U/NZ100U VL-NZ150U 14. SCHEMATIC DIAGRAMS 14-1.
VL-NZ50U/NZ100U VL-NZ150U 14-2.
VL-NZ50U/NZ100U VL-NZ150U 14-3.
VL-NZ50U/NZ100U VL-NZ150U 14-4.
VL-NZ50U/NZ100U VL-NZ150U 14-5.
VL-NZ50U/NZ100U VL-NZ150U 14-6.
VL-NZ50U/NZ100U VL-NZ150U 14-7.
VL-NZ50U/NZ100U VL-NZ150U 14-8.
VL-NZ50U/NZ100U VL-NZ150U 14-9.
VL-NZ50U/NZ100U VL-NZ150U 14-10.
VL-NZ50U/NZ100U VL-NZ150U 14-11.
VL-NZ50U/NZ100U VL-NZ150U 14-12.
VL-NZ50U/NZ100U VL-NZ150U 14-13.
VL-NZ50U/NZ100U VL-NZ150U 14-14.
VL-NZ50U/NZ100U VL-NZ150U 14-15.
VL-NZ50U/NZ100U VL-NZ150U 14-16.
VL-NZ50U/NZ100U VL-NZ150U 14-17.
VL-NZ50U/NZ100U VL-NZ150U 14-18.
VL-NZ50U/NZ100U VL-NZ150U 14-19.
VL-NZ50U/NZ100U VL-NZ150U 14-20.
VL-NZ50U/NZ100U VL-NZ150U 14-21.
VL-NZ50U/NZ100U VL-NZ150U 14-22.
VL-NZ50U/NZ100U VL-NZ150U 14-23.
VL-NZ50U/NZ100U VL-NZ150U 14-24.
VL-NZ50U/NZ100U VL-NZ150U 14-25.
VL-NZ50U/NZ100U VL-NZ150U 14-26.
VL-NZ50U/NZ100U VL-NZ150U 14-27.
VL-NZ50U/NZ100U VL-NZ150U 14-28.
VL-NZ50U/NZ100U VL-NZ150U 14-29.
VL-NZ50U/NZ100U VL-NZ150U 14-30.
VL-NZ50U/NZ100U VL-NZ150U 14-31.
VL-NZ50U/NZ100U VL-NZ150U -MEMO- 10 11 12 13 14 15 111 16 17 18 19
VL-NZ50U/NZ100U VL-NZ150U 14-32.
VL-NZ50U/NZ100U VL-NZ150U 14-33.
VL-NZ50U/NZ100U VL-NZ150U 15.
VL-NZ50U/NZ100U VL-NZ150U 138 120 108 90 75 60 54 48 42 36 27 A C KV1812K EX1394CE HVC359TR HVU359TR HVU362 64 50 44 38 30 28 24 20 16 14 10 28 37 43 49 55 61 76 91 109 121 139 32 25 22 19 15 14 12 10 8 7 5 36 48 56 64 72 80 100 120 144 160 184 ADC08351 CXA2096N PCM3008 IX0940TA 92 80 72 60 50 40 36 32 28 24 18 47 41 37 31 26 21 19 17 15 13 10 9 12 14 16 18 20 25 30 36 40 46 1 BH7277KV MB3881++ PT8214 IX0947TA 1 UPD16835 NJM2902V LV4051AT MB88146A MM1323XV 93 81 73 61 51 41 37 33 29 25 19
VL-NZ50U/NZ100U VL-NZ150U 16.
VL-NZ50U/NZ100U VL-NZ150U SIDE B J L911 C722 R739 C709 C716 C711 C713 TL1248 TL1247 TL412 Q705 Q704 C204 C212 TL204 C214 Q703 R722 R728 R709 R714 R797 R747 R729 R737 R720 R735 R733 FB201 TL914 R745 R717 R742 R743 C731 R796 R723 R772 R712 C735 R724 R736 R738 R725 R741 R731 L912 TL918 L913 C965 C738 C714 TL5702 Q1201 R1998 R1995 R1927 R911 R1929 Q1911 R1930 C905 R926 C928 R927 R920 R914 R918 C926 C903 R907 C993 R903 C902 R902 R1941 C904 R919 C925 R912 R909 R910
VL-NZ50U/NZ100U VL-NZ150U CAMERA HEAD PWB SIDE A J C26 IC21 C22 R21 C23 C21 C24 C25 I R22 L21 H R23 C33 C30 C27 C28 IC22 FB35 R24 R25 G C34 Q21 R26 FB36 R27 P52 R28 R30 F R29 C31 R31 C29 R560 P51 R34 R32 R33 C32 R558 R53 C51 C37 X21 C563 R556 E C35 R35 R38 C36 Q551 C566 R561 C D551 R576 R564 R563 R566 R562 C52 R583 IC51 R570 C53 R577 R574 C567 R568 R565 C565 D R572 R573 R582 IC552 C564 C54 R581 R569 C568 C569 R580 R575 C570 R567
VL-NZ50U/NZ100U VL-NZ150U SIDE B J TL27 TL46 TL22 I TL25 TL52 TL45 TL29 SC21 TL35 TL574 TL575 H TL21 TL54 TL53 TL47 TL37 TL24 TL34 TL57 TL44 TL36 TL33 TL43 TL39 TL59 TL30 G TL40 TL26 TL23 R51 0 TL28 TL41 TL42 R52 TL58 TL69 TL32 TL31 TL71 F SC551 R579 R578 TL55 TL63 TL56 TL564 TL557 TL558 TL72 TL555 TL553 TL551 TL552 TL554 TL560 TL556 L551 R559 TL562 TL559 C553 R553 TL561 C554 TL566 TL563 C561 R555 SC53 TL568 TL565 C556 TL570 TL567 C558 TL571
VL-NZ50U/NZ100U VL-NZ150U AUDIO I/O PWB J SIDE A I Q601 H R606 R2601 C608 Q604 R603 C2609 C2608 R2631 R605 Q603 R637 C2605 C643 C2606 C640 C644 R2618 C2607 C2602 C645 L601 R2617 R2630 R2616 R604 R2628 C611 R636 C618 R2606 R2629 R2619 R635 R634 R633 G C641 R607 C607 SC2604 IC2601 F Q605 C638 L602 C630 R2610 D601 R2609 R2620 R2627 R2625 C632 R2615 R2613 R2622 R2608 C635 R2621 C604 E P601 J601 D C B A 1 2 3 4 5 6 124 7 8 9 10
VL-NZ50U/NZ100U VL-NZ150U J SIDE B I TL609 TL608 TL2687 TL2669 TL2655 TL2662 C639 R624 0 C637 TL2689 TL2645 R632 TL2653 TL2663 C636 C633 C629 R627 C624 R623 R619 C628 TL2647 TL2683 TL2688 R628 C617 R641 TL2680 R631 C631 C620 C613 TL2644 C609 TL607 C634 C627 R630 C622 R625 R629 R620 C619 R614 R609 H R617 TL2648 R608 TL2643 R613 C612 TL2692 TL2691 R642 G TL2667 R643 TL2673 IC601 C642 R612 C2610 TL2675 TL2686 R638 TL2690 R622 C626 C621 C623 R626 R
VL-NZ50U/NZ100U VL-NZ150U CARD PWB SIDE A J I H G SC1501 F E D 1 SW1501 C B A 1 2 3 4 5 6 126 7 8 9 10
1 2 3 4 5 127 C1502 R1506 6 7 C1505 R1501 C1504 R1513 Q1502 C1501 R1512 R1508 C1503 C1510 TL1504 R1509 TL1505 R1510 TL1501 TL1514 Q1501 C1509 R1514 Q1503 TL1506 R1507 TL1507 TL1508 F TL1509 TL1510 TL1503 TL1515 G TL1513 TL1512 E TL1511 SC1502 TL1502 VL-NZ50U/NZ100U VL-NZ150U SIDE B J I H C1508 R1505 R1504 C1507 R1503 R1511 R1502 C1506 D C B A 8 9 10 0
VL-NZ50U/NZ100U VL-NZ150U INVERTER PWB J SIDE A I TL9810 BAT9802 1 TL9809 SC9802 TL9817 TL9815 C9812 BAT9801 H TL9813 T9800 R9808 TL9804TL9805 TL9818 R9809 TL9816 C9810 TL9814 TL9801 SC9801 R9804 G Q9801 C9809 C9802 L9801 TL9800 C9800 C9807 TL9803 R9803 TL9808 F SIDE B E D C 0 SW9800 B A 1 2 3 4 5 6 128 7 8 9 10
VL-NZ50U/NZ100U VL-NZ150U OPERATION PWB J SIDE A I 1 H SC2001 G F E SIDE B D R2003 R2002 0 TL2004 SW2001 R2001 RMC2001 SW2002 C2001 SW2003 TL2002 C TL2006 TL2005 B A 1 2 3 4 5 6 129 7 8 9 10
VL-NZ50U/NZ100U VL-NZ150U CCD PWB J SIDE A I TL102 TL104 TL107 TL103 TL105 TL110 TL108 TL112 C3 R107 R104 TL7 TL6 TL5 TL4 TL3 TL1 C2 C1 R3 C10 Q1 TL20 TL8 TL9 TL10 TL11 TL14 TL13 130 TL111 TL101 R7 R5 TL109 TL18 TL115 TL106 0 G R4 10 9 8 7 6 5 4 3 2 1 C5 D1 D C6 TL2 C7 F TL113 TL114 TL17 H R6 E C4 C B A
VL-NZ50U/NZ100U VL-NZ150U J SIDE B I SC101 C108 C104 H C105 R103 R109 R106 R105 C112 C111 1 C101 IC101 C107 R108 L101 G R102 C106 C109 C103 C102 C110 R101 F IC1 E D C B A 1 2 3 4 5 6 131 7 8 9 10
VL-NZ50U/NZ100U VL-NZ150U HEAD AMP PWB J Component Side SIDE A I TL301 Q302 R318 C324 R312 R323 C319 C311 R325 C333 Q303 C327 R324 C332 C323 P306 R314 R319 SC306 C340 C306 TP323 TP324 C321 C344 C318 C314 C312 C343 C309 C301 C342 R377 R315 R304 C313 C302 R317 C305 C320 C315 R331 R333 C322 C331 C330 IC301 C307 H R332 R330 TL303R311 TL302 R310 C308 R309 R316 R313 C310 R321 R308 C304 R320 SC304 SC301 G SC303 SC305 F E Wiring Side SIDE A D C B A 1 2 3 4 5 6 132 7
G 1 2 3 4 5 133 6 7 L301 8 TP340 TP338 C329 R380 TP336 TP366 TP365 TP352 TP364 TP363 TP356 TP362 TP361 TP360 TP359 TP357 TP358 TP339 TP335 TP343 TP337 TP345 TP346 TP341 TP342 TP347 TP348TP344 TP349 IC302 TP355 TP351 TP353 TP354 C345 TP309 TP301 TP308TP310 TP313 TP317 TP314 TP312 TP311 TP321 TP320 TP319 TP318 TP316 TP322 TP325 TP327 TP326 TP328 TP315 TP334 TP332 TP331 TP330 TP350 H TP329 TP333 TP304 TP306 TP307 TP302 TP303 TP305 VL-NZ50U/NZ100U VL-NZ150U J Component Side
VL-NZ50U/NZ100U VL-NZ150U DC JACK PWB J SIDE A D2900 I 0 J2900 H G F SIDE B E D P2900 C L2900 B A 1 2 3 4 5 6 134 7 8 9 10
VL-NZ50U/NZ100U VL-NZ150U Part No. ★ Description LIST/ Code 17. REPLACEMENT PARTS EXPLODED VIEWS Ref. No. Ref. No. Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. " HOW TO ORDER REPLACEMENT PARTS" Contact your nearest SHARP Parts Distributor.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. VL-SD20U Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. C162 C163 C164 C201 C202 C204 C205 C206 C207 C208 C211 C212 C213 C214 C215 C217 C218 C220 C401 C402 C403 C404 C405 C407 C410 C411 C412 C413 C414 C415 C417 C418 C419 C420 C421 C423 C424 C425 C430 C432 C435 C447 C450 C451 C452 C456 C457 C460 C462 C463 C465 C473 C474 C475 C476 C477 C478 C701 C702 C703 C704 C705 C706 C709 C711 C712 C713 C714 C715 C716 C717 C718 C719 C720 C721 Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. R713 R714 R716 R717 R718 R719 R720 R722 R723 R724 R725 R726 R727 R728 R729 R730 R731 R732 R733 R734 R735 R736 R737 R738 R739 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R755 R756 R759 R760 R761 R762 R763 R764 R765 R766 R767 R771 R772 R779 R780 R782 R796 R797 R902 R903 R904 R905 R906 R907 R908 R909 R910 R912 R913 R914 R917 R918 R919 R920 R924 R926 Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. R1471 R1480 R1481 R1482 R1483 R1700 R1701 R1702 R1703 R1704 R1705 R1706 R1707 R1708 R1709 R1710 R1711 R1712 R1713 R1714 R1715 R1716 R1717 R1718 R1719 R1720 R1721 R1722 R1723 R1724 R1725 R1726 R1727 R1728 R1729 R1911 R1912 R1913 R1914 R1925 R1927 R1929 R1930 R1931 R1940 R1941 R1943 R1944 R1945 R1950 R1956 R1957 R1958 R1959 R1968 R1969 R1980 R1981 R1982 R1983 R1984 R1985 R1986 R1989 R1990 R1991 R1992 R1994 R1995 R1996 R1997 R1998 R2801 R2802 R2803 Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. ★ Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. VL-SD20U ★ Part No. Description Ref. No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. ★ Part No. Description Code Ref. No. DUNTKB191PM00(VL-NZ100U/C/K/NZ150U) CARD PWB UNIT VSKTA2014EY-1Y VSHN2C01FU/-1 C1501 C1502 C1503 VCSATA0JJ336M VCKYCZ1CB103K VCKYCZ1AF104Z R1501 R1502 R1504 R1505 R1506 R1507 R1508 R1509 R1510 R1511 R1512 R1513 R1514 VRS-CZ1JF103J VRS-CZ1JF103J VRS-CZ1JF103J VRS-CZ1JF103J VRS-CZ1JF103J VRS-CZ1JF000J VRS-CZ1JF103D VRS-CZ1JF103D VRS-CZ1JF104J VRS-CZ1JF152J VRS-CZ1JF222D VRS-CZ1JF000J VRS-CZ1JF153D KTA2014EY HN2C01FU AB AC 6.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. VL-SD20U ★ Part No. R106 R107 R108 VRS-CZ1JF562J VRS-CZ1JF223J VRS-CZ1JF223J SC101 QCNCW3396TAZZY Description 5.6k 1/16W Metal Oxide 22k 1/16W Metal Oxide 22k 1/16W Metal Oxide Code Ref. No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No. ★ Description Code Ref. No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. VL-SD20U Part No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No.
VL-NZ50U/NZ100U VL-NZ150U VL-SD20U MECHANISM CHASSIS Ref. No. Part No. ★ EXPLODED Description VIEW Code Ref. No. ★ Part No. 429 600 383 402 435 313 436 338 341 335 435 434 332 324 352 458 393 435 394 385 376 502 432 d 466 331 F 420 401 374 391 a 434 330 357 375 390 a 391 402 b 344 b 436 470 425 353 E 397 356 339 426 383 411~ 415 1 pc. 428 381 403 457 337 382 351 354 c 431 340 342 G 392 432 456 1pc.
VL-NZ50U/NZ100U VL-NZ150U LENS VIEW Ref. No.UNIT EXPLODED Part No. ★ Description Code Ref. No. ★ Part No.
VL-NZ50U/NZ100U VL-NZ150U VL-SD20U CABINET EXPLODED Ref. No. Part No. ★ VIEWDescription Ref. No. Code 14-2 i 14-5 H ★ Part No.
VL-NZ50U/NZ100U VL-NZ150U CASSETTE CONTROL VIEW Ref. No. Part No. ★ EXPLOOD Description Code Ref. No. ★ Part No. Description 434 D 600 602 610 4±0.5 604 8.5±0.
VL-NZ50U/NZ100U VL-NZ150U VL-SD20U VL-NZ50U/NZ100U/NZ150U SERVICE JIG SPECIFICATIONS Ref. No. Ref. No. Part No. ★ Description Code 1-1. Adjusting jigs for checking the mechanism No. Name New part Part No. ★ Type number, Application 1mN·m/1.
VL-NZ50U/NZ100U VL-NZ150U Ref. PACKING No. Part No. ★ Description 18. OF THE SET No.4 Code Ref. No. Part No. ★ Description Code VL-NZ50U/C/ NZ100U/C/K No.2 No.1 VL-NZ150U No.4 No.8 No.3 No.14 No.2 No.16 No.7 No.16 No.12 No.7 No.5 No.3 No.22 No.10 No.23 No.22 No.8 No.13 No.24 No.14 No.15 No.9 No.21 No.5 No.9 No.10 No.12 No.20 No.13 No.20 No.26 No.25 No.6, No.11, No.17 No.18 No.19 ACCESSORIES No.
VL-NZ50U/NZ100U VL-NZ150U Ref. No. Part No. VL-SD20U ★ Description Ref. No. Code ★ Part No. Description Code COPYRIGHT C 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
