VL-MC500U/K SERVICE MANUAL S72M7VL-MC500 SERVICE MANUAL LIQUID CRYSTAL DIGITAL CAMCORDER MODELS NTSC VL-MC500U VL-MC500K LIQUID CRYSTAL DIGITAL CAMCORDER In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS NTSC MODELS VL-MC500U/K Page 1. IMPORTANT SERVICE NOTES ............................................................................................
VL-MC500U/K 1. IMPORTANT SERVICE NOTES connections, metal cabinet, screw heads, knobs and control shafts, etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug (a non polarized adaptor plug must be used but only for the purpose of completing these checks) on the set and repeat the AC voltage measurements for each exposed metallic part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.
VL-MC500U/K WARNING :TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO WET LOCATIONS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol mark means following. Camcorder only For continued protection against fire hazard, replace only with same type fuse. (CP1; 1.25A 24V, CP2; 1.25A 24V, CP3; 1.25A 24V, CP4; 0.5A 50V) *Note: CP4 is except for VL-MC500K. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER·SERVICEABLE PARTS INSIDE.
VL-MC500U/K CAUTION BEFORE BATTERY DESTROY NICKEL-CADMIUM BATTERY The following program is available in the United States. Please consult local environmental authorities concerning the availability of this or other programs in your area. The RBRCTM Seal SHARP participates in the RBRCTM* Nickel-Cadmium Battery Recycling Program in the United States.
VL-MC500U/K ■ PRECAUTIONS FOR USING LEAD-FREE SOLDER 1) Employing lead-free solder "Main PWB", "Camera head PWB", "Audio I/O PWB", "Card PWB", "Inverter PWB", "Operation PWB", "DC Jack PWB", "CCD PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
VL-MC500U/K 2. SPECIFICATIONS Signal System: Recording System: Cassette: Recording/Playback Time: Tape Speed: Pickup Device: Lens: Lens Filter Diameter: Monitor: Microphone: Color Temperature Compensation: Minimum Illumination: Still Image Compression System: Still Image Recording Format: Still Image Recording Medium: Power Requirement: Power Consumption: Operating Temperature: Operating Humidity: Storage Temperature: Dimensions (approx.): Weight (approx.
VL-MC500U/K 3. PART NAMES For details on the use of each control.
VL-MC500U/K 4. DISASSEMBLY OF THE SET Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery have been removed. 1. 3. LCD Panel (d) FPC (c) Battery Unit (d) (d) 1) 2) 3) 4) Detach the battery unit. Remove the three screws ((d)XiPSN17P03000). Remove the one screw ((c)LX-HZ0050TAFN). Detach the LCD cabinet in the direction of the arrow. 1) Remove the FPC of the LCD panel, and detach the LCD panel in the direction of the arrow. 4. (d) (d) (d) (d) 2.
VL-MC500U/K 5. 1) Take out the mechanism in the direction of the arrow. 2) Remove the three floating screws ((a)LX-BZ0251TAFD) and the one floating screw ((b)LX-BZ0253TAFN). 3) Remove the five screws ((d)XiPSN17P03000) to detach the battery cover. (a) (a) Battery Cover (d) (a) (d) (d) (b) (d) (d) 6. 1) Detach the lithium battery lid.
VL-MC500U/K 5. MECHANISM ADJUSTMENT JIGS AND PARTS 5-1. Mechanism check adjustment jigs 1. PB-use cassette Torque meter 2. 9DASD-1015 3. DB * 1mN·m/1.5mN·m 1. Torque gauge 2. JiGTG0045 3. CN * For use in VS-REW winding torque measurement. 1. Torque gauge head 2. 9EQTGH-DH5000 3. BW * For use with the torque gauge listed left. 1. Tension gauge 4N 2. JiGSG0400 3. BK * For measurement of pinch roller pressure. Configuration 1. Name 2. Part No. 3. Code * Model, Uses Remarks 1.
VL-MC500U/K 6. INSPECTION AND MAINTENANCE ITEMS AND INTERVALS In order to keep the mechanical section always in good condition, perform the following inspection and maintenance at regular intervals. In addition, after repair, perform the following maintenance items regardless of how long the user has been using the unit. 6-1.
VL-MC500U/K 7. MECHANICAL ADJUSTMENTS AND CHECKS The items discussed here relate to general on-site servicing (field servicing). Adjustments and replacements that require sophisticated facilities, jigs and technology are omitted. In addition, in order to maintain the characteristics that the unit has when it is new, not only are inspection and maintenance necessary, but it is absolutely necessary that, for example, the tape not be damaged, and always use jigs for adjustments that require them.
VL-MC500U/K 7-4. Back tension torque check and adjustment in record (playback) mode AC adapter used, with cassette controller assembly (1) Checking Set the torque cassette (SD-1015), and make sure in the SP record mode that the supply side torque is within the standard shown below (or in the playback mode for the tape on which the signal has been SP-recorded). (If torque ripple exists, read its center value.) 0.7 ± 0.1mN·m (2) Adjustment (Fig.
VL-MC500U/K (If the tension fluctuates, read its center value.) 15 ± 12mN 7-8. Checking of winding Tu reel base ratchet torque DC3V, without cassette controller assembly (Independent Mechanism) (1) Remove the cassette controller assembly, then apply DC3V to the loading motor and put the system into standby mode. (refer to 9-1) (2) Move the swing arm toward the S reel base side. Be careful not to cause damage to the gears and other parts in the process. (Fig.
VL-MC500U/K 8. TAPE RUNNING ADJUSTMENT 8-1. Adjustment locations · T roller, arm · Tu guide, arm · Slide chassis Adjust the height of only replaced parts with the adjusting jig. Adjustment procedure 8-2 · S guide · Pole base · Guide roller · Drum assembly · Capstan motor, etc.
VL-MC500U/K 8-4. Running rough adjustment (With cassette controller) 1) Su, Tu guide roller height adjustment Entrance side NG (1) Loosen the guide roller lock screw, then tighten loosely so that the roller turns easily. (2) Replay an alignment tape, and adjust the Sup, Tu guide roller so that the envelope sides of entrance and exit are flat. (3) Perform ± 1/4 shift, then, as in the above case, adjust until the envelope becomes flat.
VL-MC500U/K 9. MECHANICAL SECTION ASSEMBLY AND PARTS REPLACEMENT (DISASSEMBLY AND REASSEMBLY) Mechanical section disassembly and reassembly are explained in this section. For removal of the cabinet, etc., refer to 4. DISASSEMBLY OF THE SET. 1. Always replace cut washers that have been removed, for example in parts replacement, with new ones. 2. When reassembling, be careful not to allow screws, washers or foreign matter to enter. They can cause mechanical misoperation. 3.
VL-MC500U/K (6) STOP mode (5) PLAYBACK (RECORD, FF, VSF) mode The system is in the STOP (Rec Lock in CAMERA mode) The mechanism position for playback, record, FF and fast position; the S and the T pole bases are snap-fitted to the drum feed playback. base, the S brake is in contact with the S reel base, and the Tu The pinch roller is pressed to the capstan shaft, and the S/Tu brake is in contact with the Tu reel base. main brake is separated from the S/Tu reel base.
VL-MC500U/K 9-3. How to operate with the circuit board without the cassette controller assembly. In this method, if the procedure is followed incorrectly there is danger of damaging the mechanism and the tape, so except in special cases, such as when measuring the VSR torque, do not perform this procedure. Normally operate this unit with the cassette controller assembly attached. Be sure to follow each caution mentioned. (1) Apply DC3 ~ 4V to the loading motor to enter the standby mode.
VL-MC500U/K 9-5. Reassembly 9-5-1. Reassembly in side of the main chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the main chassis). 1. Groove grease 4.
VL-MC500U/K 9-5-2. Reassembly in side of the Slide chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the slide chassis) 2. 1. Sensor FPC cover Grease F K Main brake SPR. 391 H 393 F Tu main brake 374 N T spring hanging ANG 356 S guide hexagon 428 nut Tu reel base Ass'y 375 N O 411 Fit the main brake SPR from above, and close with the hook.
VL-MC500U/K 9-5-3. Main chassis assembly and slide chassis assembly assembling method (1) Enter the coupling mode. (In this position, the cam groove of the T arm operation lever in the figure is parallel to the side of the main chassis, and the poll base is slightly moved.
VL-MC500U/K GREASE/OIL APPLICATION From rear surface side Rear surface · groove side surface Front surface · rear surface · groove side surface Drum base assembly From rear surface side Main cam Loading lever Tu loading arm S loading arm Intermediate gear angle Enabled after assembling Including groove side surface Enabled after assembling O : Oiling(Cosmo Hydro HV22) G : Greasing(Moly Coat YM-103) : Greasing(Moly Coat YM-103) Pinch control lever Capstan FPC stopper T arm control lever Side
VL-MC500U/K 10. ADJUSTING THE ELECTRICAL CIRCUITS Before starting the electric circuit adjustment • The adjustment methods described herein are used, in most cases, when the expendable mechanical parts, including the video head, have been replaced, at which time the electrical circuits need to be readjusted. Before adjusting the electrical circuits, make sure that the mechanism works properly (i.e., the mechanism is properly adjusted).
16 13 LENS UNIT LENS FPC Direct connection QSW-ZA008WJZZ OPERATION SW UNIT QSW-ZA007WJZZ POWER ZOOM SW UNIT MIC UNIT RMiCCA001WJZZ CCD PWB SC101 9 SC1002 TURN SW UNIT QSW-ZA009WJZZ HEAD AMP UNIT SC1201 SC1202 8 SC900 3 P306 J600 SPEAKER VSP0020P-A1WN 15 P600 BATTERY TERMINAL UNIT QTANZA005WJZZ 14 JIG FOR ENV.
VL-MC500U/K [TEST POINT] (Wiring board diagram: Main Side A) TL1242(INT MIC R) EE level check Frequency character check TL1216(INT MIC L) EE level check Frequency character check R446 IC405 TL3328 R3714 R3712 R3704 R3715 R3708 R1202 P1200 L2800 C2804 TL2824TL2825TL2826R2853 C2828 C2824 C2822 C404 C405 C2810 R407 R416 C2825 SC2801 R2823 C2811 R2825 C2812 R2830 TL3321 R3301 TL3323 TL3327 TL3326 TL3324 CP2 R2808 FB456 C463 C476 R3495 TL3340 C2814 L2803 C2826 R2856 C2823 SC90
VL-MC500U/K [Making adjustments] Adjusting the servo system controller and related parts 1. Setting the system codes Replacement of IC705 E2PROM requires the following data to be set in this order. [Procedure] Set the unit to the VCR mode and set the data for each address. Code Address Data 1. Model code 01 09 00 FF 2. Destination code 3. Specification code 02 0A 03 0B 01 FE 1C E3 4. Menu selection code 5. Software switching code 6.
VL-MC500U/K 3. SHUT OFF adjustment Mode Procedure Examples VCR ADJ mode 1) Load a recordable tape, and set the camera mode. 2) Press the "CONTINUE" and then the "TEST SEL" on the remote control for adjustment to enter the TEST mode (T-01 blinks). 3) Select T-03 with the FF or REW key and then press the PB key. 4) Observing the power voltage from TL900(-), set it so that TL904(+) obtains 6.00V ± 50mV. 5) Press the "DISPLAY" button on the main unit. Turn off the power and the adjustment is completed.
VL-MC500U/K ADJUSTING THE VIDEO I/O CIRCUIT SYSTEM (Wiring board diagram: Main Side A) L907 C937 C953 R995 L912 Q903 R956 TL908 R987 C957 C938 R970 C973 C970 J5701 FL5701 C931 Q906 C972 L916 C975 R989 R988 Q907 C971 L917 TL1473 R1477 TL1470 T900 TL1474 PCO D/A-Y C974 R1471 TL1472R1472 R1476 TL1476 R1475 R950 R951 C992 R1479 TL1475 L923 R996 Q905 R990 Q911 C980 C935 TL1477 R1480 C933 R1478 C960 TL1474 C991 TL1471 C990 J1401 L915 L900 L919 L904 R7426 J7401
VL-MC500U/K ADJUSTING THE LCD CIRCUIT * To make this adjustment, set the backlight switch to the "NORMAL" position.
VL-MC500U/K 4. White Balance adjustment Test point Mode Procedure LCD panel display surface Address VCR ADJ 584, VCR ADJ 586 VCR AV input 1) Input the white 40% signal to AV input. 2) Input the white 40% signal to the standard monitor, and adjust it to become equal to that of the screen. Standard monitor Adjustment rating Remark Examples Make this adjustment after 5-minute or longer aging. • During LCD monitor replacement. LCD Panel • During IC4401, IC705 replacement.
VL-MC500U/K DV INTERFACE (IEEE1394) ID SETTING This unit has a DV interface function conforming to IEEE1394. Therefore, each individual ID number must be used for each unit. Since this ID is written on the E2PROM (IC302) on the head amp PWB, the ID must be newly written when replacing this IC or the head amp PWB. Address 180, 17F, 17E Mode VCR Adjustment rating ID number obtained from the URL below Procedure 1) Refer to the ID code application below.
VL-MC500U/K (5) Click on [Repair use]. Click (6) Input the necessary information for the application. For the indispensable input items, be sure to input them. Select the [Group/company] and [Kind name] from the list. Input the [Model name]. Input the [Serial number]. Input the [Site/department of repair]. (7) Click on [motion]. The confirmation screen will appear. (8) Click on [Yes]. 2. Print the application result. (1) Print out the application result screen.
VL-MC500U/K 10-2. Camera Section Adjustments 10-2-1. Camera section service (1) Camera adjustment is performed after the set has been completed. (2) Subjects, measuring instruments and jigs needed for camera section service and adjustments • • • • • • Gray scale chart Color bar chart Oscilloscope Digital voltmeter Halogen lamp: 2 pcs.
VL-MC500U/K 4) Operation flow FF or REW PLAY FF or REW PLAY STOP Address is selected and specified, with the data called. Then the called data are selected and fixed. The operation flows in this sequence. 5) When the adjustment is complete: Press the "CONTINUE" key to let the "CAM ADJ" display disappear from the screen.
VL-MC500U/K (4) Camera signal system adjustment mode In the camera signal system adjustment mode, the automatic white balance is disabled to allow for the adjustment of the camera unit. At this time, the white balance mode is fixed at the INDOORS mode and the focus mode is switched to the manual focus mode. 1) Shifting to the camera signal system adjustment mode Set the data for the address "0000" to " 00". ] This shifts the camera signal system adjustment mode.
VL-MC500U/K 10-2-4. Adjustment procedures Adjustment method Item (1) Auto-focus adjustment Set the unit to the auto-focus function adjustment mode and write data to the address "13FD" one after another. This executed the adjustments automatically. The items to be adjusted are as listed below. Every time an adjustment is made properly, the data "FF" is written to the address. After each adjustment, make sure that the adjustment has been made properly, and then go on to the next adjustment item.
VL-MC500U/K Adjustment method Item (4) Iris AE coarse adjustment (1) Video output is observed with the oscilloscope in the grey scale standard record state, • Measurement terminal: the data of address "0002" is rewritten, and the luminance signal level is adjusted white S terminal luminance signal output to 680 ± 10mVp-p, gray of the background 330 ± 10mVp-p.
VL-MC500U/K Adjustment method Item (7) White balance adjustment • Measurement terminal: EE output • Address: "0128" INDOOR_W/B R "012A" INDOOR_W/B R • Measuring instrument: Vector scope • Object: Grey scale • Data variation width: "0000" to "03FF" (1) White balance adjustment is performed repeatedly.
VL-MC500U/K Adjustment method Item (12) Iris AE adjustment • Measurement terminal: S terminal luminance signal output (75 Ω termination) • Address: "0002" AE_CVT • Measuring instrument: Oscilloscope (horizontal sync) • Object: Grey scale • Data variation width: "0000" to "00FE" (1) Set the unit to the normal operation mode (write the data " FF" to the address "0000").
VL-MC500U/K 11. USEFUL TIPS (PROBLEMS DIFFER FROM THOSE FOUND ON VHS OR 8MM DECKS BECAUSE THE SIGNALS ARE DIGITALLY PROCESSED.) Camera (EE mode) Picture fails to appear Camera (REC mode) VCR (PB mode) VCR (EE mode) Picture fails to appear when tape recorded on this unit or another unit is played back. (EE OK) Blueback fails to appear.
VL-MC500U/K 12. SIGNAL FLOW DIAGRAMS 12-1.
VL-MC500U/K WAVEFORM DIAGRAM (DURING COLOR BAR PLAYBACK) 12-3.
VL-MC500U/K 12-5. FLOW IN PB MODE (AUDIO) WAVEFORM DIAGRAM (1.
IC2501 LENS DRIVER LENS 45 IC503 D/A-CON IC101 CDS/AGC ADC PB REC (EE) USB CAMERA Section IC501 LENS MICON IC2502 IRIS DRIVE 72.
IC22 V-Driver VHiUPD16510-1 20P OFD V1, V2, V3, V4 H1-CLK, H2-CLK, RS-CLK, HL-CLK CCD OUT 46 X21 72.
J1401 CAMERA SECTION BLOCK DIAGRAM CAM ENGINE 47 SEP Y IN/OUT SEP C IN/OUT VIDEO IN/OUT SEP-Y-IN VIDEO-IN IC1431 VHiNJM2535V-1 ZYP0 7 ZCP0 7 ZUVSELP ZCLKP ZHDP ZVDP IC1401 VIDEO I/O VHiLA73070V-1 16P A-Y-OUT A-C-OUT A-Y/COMP_V_IN A-C_IN IC4401 VIO ENGINE RH-iXA204WJZZ 303P CDY0 7, CDC0 7 REC (EE), PB PB REC (EE) R G B CLD, SPD, CTR, EX1, EX2,PSS1,SPS, RES, CLS, LOW CVDR, CHDR I/O SEL SC2801 VR, VG, VB IC2800 LCD INTERFACE VHiMM1323XV-1 24P IC452 REC/PB ENGINE RH-iX0809TAZZ 368P CD
DI00 48 REC (EE), PB PB REC (EE) 15 11 7 7 XCS, XWE, XRAS, XCAS, XUDQM, XLDQM, XCKE, CLK18M1IV SM-ADR0 CVDR CHDR I/OSEL CDUVSELP CDHDP, CDVDP IC407 Codec External Memory 16M SDRAM RH-iXA193WJZZ 60P IC4401 VIO ENGINE RH-iXA204WJZZ 303P CDY0 CDC0 IC452 REC/PB ENGINE RH-iX0809TAZZ 368P X401 24.
REC (EE), PB PB REC (EE) REC/PB ENGINE BLOCK DODAT PDAD PDDA ADMCLK ADBCK ADLRCK DFSO DFSI AIDAT CS-1394, RD-1394, WR-1394 TPA-, TPA , TPB-, TPB AUD R AD IN AUD L AD IN AUD R DA OUT AUD L DA OUT IC1602 16Bit ADC/DAC VHiPCM3008+-1 16P MECHA/SYSTEM MICON DV CONNECT IC600 AIO VHiLA74206W-1 64P INT MIC SP OUT AUDIO R I/O AUDIO L I/O SPEAKER AV JACK VL-MC500U/K 13-5.
IC1 CCD Sensor 50 Focus-Motor Driver X21 72MHz IC503 D/A Converter IC1002 Gyro Amp RMC91 Gyro Sensor IC21 Timing Generator Zoom-Motor Driver IC2501 Iris Drive IC2502 Iris Amp IC22 V-Driver IC101 CDS AGC ADC CAMERA IC501 Lens µ-com CCD IC3701 CAM/CARD µ-com SSG Digital Auto C-Process Y-Process CAM ENG IC3702 16M SDRAM Electric Zoom Image Stabilizer Digital Noise Reduction IC201 Sirial Data PB Y/C Data IC203 64M SDRAM REC /PB Y/C Data MAIN VL-MC500U/K 13-6.
VL-MC500U/K -MEMO- 51
VL-MC500U/K 14. SCHEMATIC DIAGRAMS 14-1.
VL-MC500U/K 14-2.
VL-MC500U/K 14-3.
VL-MC500U/K 14-4.
VL-MC500U/K 14-5.
VL-MC500U/K 14-6.
VL-MC500U/K 14-7.
VL-MC500U/K 14-8.
VL-MC500U/K 14-9.
VL-MC500U/K 14-10.
VL-MC500U/K 14-11.
VL-MC500U/K 14-12.
VL-MC500U/K 14-13.
VL-MC500U/K 14-14.
VL-MC500U/K 14-15.
VL-MC500U/K 14-16.
VL-MC500U/K 14-17.
VL-MC500U/K 14-18.
VL-MC500U/K 14-19.
VL-MC500U/K 14-20.
VL-MC500U/K 14-21.
VL-MC500U/K 14-22.
VL-MC500U/K 14-23.
VL-MC500U/K 14-24.
VL-MC500U/K 14-25.
VL-MC500U/K 14-26.
VL-MC500U/K 14-27.
VL-MC500U/K 14-28.
VL-MC500U/K 15.
VL-MC500U/K 138 120 108 90 75 60 54 48 42 36 27 A C HVC202A HVU362 KV1812K EX1394CE HVU359TR 64 50 44 38 30 28 24 20 16 14 10 28 37 43 49 55 61 76 91 109 121 139 32 25 22 19 15 14 12 10 8 7 5 36 48 56 64 72 80 100 120 144 160 184 PCM3008 IXA353WJ LA73070V UPD16S10 92 80 72 60 50 40 36 32 28 24 18 47 41 37 31 26 21 19 17 15 13 10 9 12 14 16 18 20 25 30 36 40 46 1 BH7277KV MB3881++ MN52A6CD H49334HN 1 NJM2902V MB8346BV MM1449XQ MM1323XV ADC08351 93 81 73 61 51 41 37 33 29 25 19 5 LB11990W
VL-MC500U/K 16.
VL-MC500U/K SIDE B R754 C737 R781 R779 C739 Q601 C644 VA601 R602 Q605 R611 C643 C605 R622 Q602 C946 L905 C949 R979 R974 Q1911 R1927 R1931 R1990 C1980 R1914 Q1931 R1913 C942 R980 C941 R1929 R1930 R1991 Q1908 R1925 Q901 IC901 TL1905 TL1904 Q1906 IC1902 R920 C1906 C928 R926 R1999 R924 R927 C905 R918 R914 C926 C993 C903 R907 R903 C902 R902 C904 R919 R911 C925 R912 R909 R910 C965 R1992 R1994 R933 C908 R936 C907 R928 Q1932 R1995 C1981 R1998 R1996 C1
VL-MC500U/K CAMERA PWB SIDE A C2501 J C2505 R2501 C2506 R2504 C2509 R556 C2503 R503 R501 C501 C2510 R502 R2510 1 R2507 R2509 G R2506 C2512 C2513 R2534 C2507 L501 R2505 C502 R513 C2502 C2511 C2520 C2518 R2513 R2516 C2515 R510 R514 C509 R2515 R581 R2514 C2519 IC2501 R2531 C2516 R2508 C2521 C2508 IC2502 R2525 C2517 R2526 R2520 R2512 R2527 R2523 D551 R2511 H R2503 R2502 C2504 R2530 R2528 I C507 C510 TL1027 R509 F IC503 IC501 C1016 TL511TL512 TL510 TL10
VL-MC500U/K SIDE B J TL2514 I TL2502 R2532 R2518 TL2512 TL2501 Q2502 R2521 R2519 H Q2505 TL2516 R2522 R2535 TL2503 Q2503 Q2501 R2524 Q2506 TL2505 Q2504 R2529 R2517 TL2509 C1018 TL2511 C1019TL1039 C1001 TL2513 C2514 C1017 TL1036 TL1001 TL1037 TL2517 R2533 R1013 TL2518 G TL1004 TL1018 E R1007 TL2507 TL2508 R1009 C1022 TL1020 C1007 TL1014 TL1016 C511 SC1001 TL1010 TL1012 R1005 TL1008 R515 TL1006 TL1009 TL1011 R1011 R1016 C1005 TL1013 C1011 C1014 TL1015 R101
VL-MC500U/K CARD PWB SIDE A J I H 2 P6600 G F SC1502 SC1501 E D P1504 C B A 1 2 3 4 5 6 116 7 8 9 10
VL-MC500U/K SIDE B J I H R6606 C6603TL6603 C6610 R6602 G R6610 C6607 C6606 1 R6605 C1513 C1516 C1500 Q1501 R1500 Q1500 C1501 TL1504 TL1501 C6602 C6611 C6608 R6608 TL1527 R1514 TL1524 TL1523 TL1520 TL1515 R1515 R6600 R6601 R6609 R6607 C1521 C1520 C6600 C6601 Q6600 TL6602 C6604 F TL1505 C6605 TL6601 IC6600 R6603 IC6601 TL1518 C1514 R1516 TL1503 R6604 R1501 R1505 R1502 R1506 R1503 R1507 C6609 TL1513 TL1502 TL1509 E TL1521 TL1526 TL1508 TL1510 TL1514 TL1516 C
VL-MC500U/K INVERTER PWB J SIDE A C9807 I Q9801 T9800 R9803 C9802 R9804 H TL9804 C9810 G C9800 L9801 TL9802 F TL9807 C9812 TL9801 C9801 TL9806 TL9817 TL9805 TL9813 E TL9815 SC9801 D 1 C R9809 R9808 TL9816 TL9814 TL9818 TL9803 B SC9802 A 1 2 3 4 5 6 118 7 8 9 10
VL-MC500U/K J SIDE B I H G F E SW9800 D C B A 1 2 3 4 5 6 119 7 8 9 10
VL-MC500U/K CCD PWB J SIDE A I RMC91 TL91 H TL93 C92 TL92 G TL5 R4 TL7 F D2 C6 R6 C8 C5 R5 C1 D1 1 C23 R3 Q1 TL6 TL1 TL2 TL3 TL4 C2 TL12 C4 C9 TL10 TL9 E R26 TL14 TL13 C109 TL11 R24 C33 R37 R34 TL109 IC21 C35 TL107 C47 R35 R43 R21 R31 C27 R30 TL111 C30 C32 FB22 R41 R39 L23 R40 R32 X21 C22 R38 C38 R27 R33 C C40 R23 C46 D R22 Q21 C34 R28 R7 C3 C39 C37 C29 TL112 C36 C41 SC101 B TL102 TL8 TL103 TL104TL105TL106TL108TL110TL113 A 1 2 3
VL-MC500U/K J SIDE B I IC22 C43 C24 R29 C7 R36 C44 C21 C45 C91 H P101 C42 IC1 G F E TL126 2 C110 C115 C108 C102 TL125 C114 R101 D R106 R102 R107 TL124 TL123 C107 IC101 R108 TL122 R103 R110 C112 C116 C113 C111 C106 C104 C105 TL121 P102 C R109 C103 C101 TL120 TL119 L101 TL118 TL117 B L102 TL116 TL115 A 1 2 3 4 5 6 121 7 8 9 10
VL-MC500U/K HEAD AMP PWB J Component Side SIDE A I TL301 C305 C330 R318 C324 R312 R323 C319 C311 R325 C333 Q303 C327 R324 C332 C323 P306 R314 R319 SC306 C340 C306 TP323 TP324 C321 C344 C318 C314 C312 C343 C309 C301 C342 R377 R315 R304 C313 C302 C320 C315 R331 R333 C322 Q302 C331 R317 IC301 C307 H R332 R330 TL303R311 TL302 R310 C308 R309 R316 R313 C310 R321 R308 C304 R320 G SC301 SC304 SC303 SC305 F E Wiring Side SIDE A D C B A 1 2 3 4 5 6 122 7 8 9 10
B 1 2 3 4 5 123 6 7 8 TP340 TP338 C345 L301 TP336 TP339 TP335 TP345 TP343 TP337 TP346 TP341 TP347 TP342 TP309 TP301 TP308TP310 TP313 TP317 TP314 TP312 TP311 TP321 TP320 TP319 TP318 TP316 TP322 TP328 TP355 TP351 TP353 TP354 TP340 TP338 C329 R380 TP336 TP366 TP365 TP352 TP364 TP363 TP356 TP362 TP361 TP360 TP359 TP357 TP358 TP339 TP335 TP345 TP343 TP337 TP346 TP341 TP347 TP342 TP349 TP348TP344 IC302 TP325 TP327 TP326 TP329 TP315 TP334 TP332 TP331 TP330 L301 TP349 TP348TP344 IC30
VL-MC500U/K -MEMO- 124
VL-MC500U/K Part No. ★ Description LIST/ Code 17. REPLACEMENT PARTS EXPLODED VIEWS Ref. No. Ref. No. Part No. ★ Description Code DUNTKB321QA01(VL-MC500K) DUNTKB400QA00(VL-MC500U) MAIN PWB UNIT ELECTRICAL PARTS LIST INTEGRATED CIRCUITS Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Les pièces marquéss " å " sont importantes pour maintenir la sècurité de l'appareil.
VL-MC500U/K Ref. No. VL-SD20U Part No.
VL-MC500U/K ★ Ref. No. Part No.
VL-MC500U/K Ref. No. C956 C957 C959 C960 C962 C963 C964 C965 C966 C967 C968 C969 C970 C971 C972 C973 C974 C980 C981 C982 C983 C990 C991 C992 C993 C1200 C1201 C1202 C1402 C1406 C1407 C1408 C1409 C1410 C1411 C1412 C1415 C1416 C1417 C1418 C1419 C1431 C1432 C1433 C1434 C1435 C1436 C1437 C1438 C1439 C1440 C1441 C1603 C1604 C1605 C1608 C1610 C1611 C1617 C1701 C1702 C1703 C1704 C1705 C1706 C1707 C1708 C1709 C1710 C1711 C1712 C1713 C1714 C1715 C1716 VL-SD20U Part No.
VL-MC500U/K ★ Ref. No. Part No.
VL-MC500U/K VL-SD20U Ref. No. Part No.
VL-MC500U/K Ref. No. R928 R929 R930 R931 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R946 R948 R949 R950 R951 R952 R954 R955 R956 R957 R959 R960 R962 R965 R966 R968 R970 R972 R973 R974 R975 R977 R979 R980 R982 R983 R987 R988 R989 R990 R995 R996 R999 R1201 R1202 R1402 R1403 R1404 R1405 R1406 R1413 R1414 R1419 R1422 R1423 R1424 R1431 R1432 R1433 R1434 R1435 R1436 R1437 R1438 R1439 R1440 R1441 R1442 R1462 R1471 Part No.
VL-MC500U/K Ref. No. R2820 R2821 R2822 R2823 R2824 R2825 R2829 R2830 R2831 R2833 R2835 R2840 R2851 R2852 R2853 R2856 R2857 R2858 R2859 R2860 R2861 R2862 R2863 R3401 R3402 R3404 R3406 R3407 R3409 R3410 R3411 R3412 R3413 R3414 R3415 R3416 R3417 R3418 R3419 R3420 R3421 R3422 R3423 R3424 R3425 R3427 R3428 R3429 R3430 R3432 R3435 R3436 R3437 R3442 R3445 R3451 R3452 R3454 R3457 R3462 R3463 R3468 R3469 R3470 R3471 R3472 R3473 R3478 R3479 R3480 R3481 R3482 R3486 R3487 R3488 VL-SD20U Part No.
VL-MC500U/K Ref. No. ★ Part No.
VL-MC500U/K Ref. No. VL-SD20U Part No.
VL-MC500U/K Ref. No. ★ Part No. Description Code MISCELLANEOUS PARTS SC9801 QSOCN0871TAZZY Socket, 8Pin SC9802 QCNCWA002WJZZY Connector, 4Pin SW9800 QSW-M0019TAZZY Switch AC AE AC ★ Ref. No. Part No.
VL-MC500U/K VL-SD20U ★ Ref. No. Part No.
VL-MC500U/K Ref. No. Part No.
VL-MC500U/K VL-SD20U ★ Ref. No. Part No.
VL-MC500U/K Ref. No. Part No. ★ Description Code Ref. No.
VL-MC500U/K VL-SD20U MECHANISM CHASSIS Ref. No. Part No. ★ EXPLODED Description VIEW Code Ref. No. ★ Part No.
VL-MC500U/K LENS VIEW Ref. No.UNIT EXPLODED Part No. ★ Description Code H Ref. No. 12-6 m ★ Part No.
VL-MC500U/K VL-SD20U CABINET EXPLODED Ref. No. Part No. ★ VIEWDescription Ref. No. Code ★ Part No.
VL-MC500U/K CASSETTE CONTROL VIEW Ref. No. Part No. ★ EXPLOOD Description Code Ref. No. ★ Part No. Description 434 D 600 602 610 4±0.5 604 8.5±0.
VL-MC500U/K VL-SD20U VL-MC500U/K SERVICE Ref. No. Part No. ★ JIG SPECIFICATIONS Description Code 1-1. Adjusting jigs for checking the mechanism No. Name New part Ref. No. Part No. ★ Type number, Application 1mN·m/1.
VL-MC500U/K Ref. PACKING No. Part No. ★ Description 18. OF THE SET Ref. No. Part No.
VL-MC500U/K Ref. No. VL-SD20U Part No. ★ Description Ref. No. Code ★ Part No. Description Code COPYRIGHT C 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
