VL-E990E VL-A110U/UC VL-AH130U SERVICE MANUAL SERVICE MANUAL S21O3VL-A110U LIQUID CRYSTAL CAMCORDER Hi 8 NTSC LIQUID CRYSTAL CAMCORDER Hi 8 VL-A110U/UC MODELS VL-AH130U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. NTSC CONTENTS MODELS VL-A110U/UC/AH130U Page 1. IMPORTANT SERVICE NOTES .......................................................................
VL-A110U/UC VL-AH130U VL-E990E 1. IMPORTANT SERVICE NOTES connections, metal cabinet, screw heads, knobs and control shafts, etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug (a non polarized adaptor plug must be used but only for the purpose of completing these checks) on the set and repeat the AC voltage measurements for each exposed metallic part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.
VL-E990E VL-A110U/UC VL-AH130U WARNING :TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO WET LOCATIONS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol mark means following. Camcorder only For continued protection against fire hazard, replace only with same type fuse. (CP901; 2.5A 64V, CP902; 2.5A 64V, CP903; 2.5A 64V) CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER·SERVICEABLE PARTS INSIDE.
VL-A110U/UC VL-AH130U VL-E990E CAUTION BEFORE BATTERY DESTROY NICKEL-CADMIUM BATTERY The following program is available in the United States. Please consult local environmental authorities concerning the availability of this or other programs in your area. The RBRCTM Seal SHARP participates in the RBRCTM* Nickel-Cadmium Battery Recycling Program in the United States.
VL-E990E VL-A110U/UC VL-AH130U 2. SPECIFICATIONS Signal System: Recording System: Cassette: Recording/Playback Time: Tape Speed: Pickup Device: Lens: Lens Filter Diameter: Monitor: Microphone: Color Temperature Compensation: Minimum Illumination: Video Output Level: Audio Output Level: Speaker Output: Power Requirement: Power Consumption: Operating Temperature: Operating Humidity: Storage Temperature: Dimensions (approx.): Weight (approx.
Speaker Microphone 6 Cassette compartment door Lens hood Remote sensor Rear view LCD monitor screen Battery compartment door Tripod socket Battery compartment door release DISPLAY button Power switch (CAMERA/VCR select switch) Hand strap FADE button Shoulder strap loop Power Zoom Wide angle/ Telephoto control VOLume control RECord START/STOP button Operation buttons Bottom view MENU button CHARGE indicator Lithium battery holder Shoulder strap loop Cassette compartment door release
VL-E990E VL-A110U/UC VL-AH130U 4. DISASSEMBLY OF THE SET 4-1. REMOVAL OF THE CAMERA SECTION Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery has been removed. (b) Connector (b) Pull out (a) (1) Camera front cabinet (d) (a) 5. Remove the connector of the 6-cell detection switch, and remove two screws ((b)LX-HZ0018TAFF) fixing the battery catcher. 1.
VL-A110U/UC VL-AH130U VL-E990E 4-2. DISASSEMBLY OF THE VCR MAIN BODY <1. Removal of the VCR lid shaft> Area A (b) (k) (2) Remove five screws ((b)LX-HZ0018TAFF). (1) Remove one screw ((k)LX-HZ0063TAFC).
VL-E990E VL-A110U/UC VL-AH130U <3. Removal of the VCR lid> Caution for installation of the VCR lid Microphone connector VCR lid Area B When installing the VCR lid, move the VCR lid in the arrow direction, keeping the VCR lid parallel to the main body as shown above. (1) Disconnect the microphone connector. <4.
VL-A110U/UC VL-AH130U VL-E990E <8. Removal of the Lithium PWB> (b) LCD unit Lithium PWB Main PWB Connector Connector Inverter transformer (3) Remove two screws ((b)LX-HZ0018TAFF) and two connec- (1) Remove the connector of the Lithium PWB from the Main PWB. tors, and remove the LCD unit (with inverter) from the main (2) Move the lithium unit in the direction of the arrow. body. <9. Disassembly of the frame V> <6.
VL-E990E VL-A110U/UC VL-AH130U Claw C Claw B View E Claw A Claw D View F Note: When fixing the cassette compartment lid, first engage the claws A and B, and then engage the claws C and D, verify that the four claws (A, B, C and D) of the cassette compartment lid are securely engaged as shown in the view above. <11. Disassembly of the LCD panel> (2) (1) Claw (A) Claw (A) Reflection sheet Light guide plate Diffusion sheet Lugs Prism sheet Lugs (3) Claw (B) Disengage the claw, and remove the LCD panel.
VL-A110U/UC VL-AH130U VL-E990E 4-3. REPLACEMENT OF CCD SENSOR 4-3-1. BEFORE REPLACEMENT 1) The CCD image sensor is more sensitive to electrostatic breakage than C-MOS LSI. Therefore sufficient means to prevent electrostatic damage must be taken when it is replaced. • Ground the soldering iron. • Ground also the human body, using the wrist strap(through an 1 Mohm resistor). • Until the CCD sensor is mounted on the PWB, fit it to the conductive sponge, and short-circuit the foot lead.
VL-A110U/UC VL-AH130U 5. MECHANISM ADJUSTMENT 5-1. MECHANISM CHECKING/ADJUSTING JIGS, TOOLS AND PARTS 5-1-1. Mechanism checking/adjusting jigs and tools 1. Cassette torquemeter for PB 2. JiG8T-012 3. CV * (10 g·cm/25 g·cm) 1. Cassette torquemeter for VS-REW 2. JiG8T-032 3. CV * (50 g·cm/25 g·cm) 1. Torque gauge 2. JiGTG0045 3. CN * For measurement of loading brake torque Configuration 1. Name 2. Part No. 3. Code * Model, Uses Remarks 1. Torque gauge head 1. Torque driver 2.
VL-A110U/UC VL-AH130U 5-2. ITEMS AND TIMINGS OF INSPECTION AND MAINTENANCE The mechanism of VCR needs the following periodic inspection and maintenance in order that it maintains its high quality. Also, after the machine is repaired, execute the following maintenance and checks regardless of how long it has been used. 5-2-1. Inspection and maintenance list Checking/Maintenance point 500 Usage time (hrs.
VL-A110U/UC VL-AH130U 5-3. MECHANISM CHECKS AND ADJUSTMENTS The description given below relates to the general field services, but does not relate to the adjustment and replacement that require high level equipments, jigs, and technical skills. In order to maintain the initial characteristics of the machine, it is necessary to execute the maintenance and check and to prevent damage to tapes and other parts. For adjustments which need jigs, be sure to use the jigs.
VL-A110U/UC VL-AH130U 5-3-4. Checking and adjusting the tension pole position (1) Check When winding of P6-120 tape is started, check whether the tension pole is in the specified position against Si roller as shown or not. If it is not in the specified position, remove the cassette and adjust the position in the following procedure. (2) Adjustment 1. Don’t set up any tape, and select the PB mode. (Refer to Item 5-5-1-(4).) 2.
VL-A110U/UC VL-AH130U 5-4. ADJUSTMENT OF MECHANISM TAPE TRAVEL SYSTEM Sup tilted pole 5-4-1. Preparation for adjustment Sup GR (1) Clean the tape running areas (guide poles, rollers, drum, Capstan shaft, Pinch roller) (Figure 1) Si roller (2) Connect the oscilloscope to the following TPs. RF output ..... TL7410 H-SW-P ....... TL7417 GND ............. TL7413 (3) Playback the alignment tape (VR2ABOPS). Tension pole (4) Ascertain that each guide is free from remarkable curl.
VL-A110U/UC VL-AH130U 5-4-4. Adjusting the Tu guide Height setting jig Master plane (JiGMP-MX7U) Upper flange After replacement of Tu guide preset and adjust the height. (1) Tu guide height presetting (Figure 6) Adjust the height from the upper surface of mechanism chassis to the upper surface of lower flange with the aid of jig. Lower flange Figure 6 (2) Adjusting the Tu guide (Figure 7) 1 Playback the alignment tape (VR2ABOPS).
VL-A110U/UC VL-AH130U 5-5. MECHANISM ASSEMBLING AND PARTS REPLACEMENT (DISASSEMBLING AND ASSEMBLING) Below is given an explanation of assembling of mechanism and its parts replacement. The removal of cabinet and Circuit Board is explained in the relevant service manual. Notes 1 After removal of cut washers be sure to replace them with new ones. 2 Do not place the mechanism upside down on the table. Otherwise, the mechanism part may be deformed or damaged, resulting in malfunction.
VL-A110U/UC VL-AH130U 5-5-2. Cassette control ass’y Lock Lever (1) Set the unit to the EJECT mode, and let the housing stand upright. Or set the unit to the STANDBY mode, press the lock lever in the arrow direction, and let the housing stand upright. (See Fig. 5: in the direction a or b ) (When pushing in the direction a , slightly lift the housing by hand to release the lock lever.) (2) Remove the four screws 2 and take out the down guide 3.
VL-A110U/UC VL-AH130U 5-5-5. Phase matching The phase of the following parts must be matched as shown in the figure right. (Ascertain that the marks and round holes align.) (1) Lo relay gear (3) Sub-cam (2) Main cam (4) Mode switch Lo relay gear Phase alignment mark (Round hole) Mode switch Phase alignment mark ( Mark) Phase alignment mark (Round hole) 5-6. MECHANISM ASSEMBLING METHOD (1) Adjust the phase of each part. (2) Install screws and washers.
VL-A110U/UC VL-AH130U (7) Install the guide rail assembly taking care to position it (4) Install the loading block assembly and the capstan motor. correctly. (5) Install the drive gear. At this time, pay attention to the direction of gear. (The small gear must be located in the B A chassis side.) a a A a Make sure not deform the arm. Loading motor a Capstan motor a A D C Move FF downwards Install the motor under this plate. Drive gear Position the small gear of the drive towards the chassis.
VL-A110U/UC VL-AH130U (8) Install the drum assembly in the chassis. (9) Install the tape guide in the drum assembly. (10) Install the Si roller. (11) Install the slide chassis. T arm guide B Tape guide A Slide this part towards the T arm. Place the slide chassis on the guide rail. A Drum assembly B A A Si roller B Roller spring Main cam pin B Insert the main cam pin into the hole of cam of slide chassis. Sup reel base Item A M1.4 x 1.5 ø4 B M1.4 x 1.5 ø3.
VL-A110U/UC VL-AH130U 6. ADJUSTMENT OF VCR AND CAMERA 6-1. INITIAL SETTING OF E2PROM IC 6-1-1. E2PROM data alterable ways 1) Set the switch of main body to CAM, and use the remote control (RRMCG0033TASA) for adjustment to turn on the adjustment mode. 2) VCR adjustment address setting. V ADJ 0000 “0000” is blinking After an objective address was established, play key is pushed and set. In addition, numerical change uses a “REW” or “FF” key. 3) VCR adjustment data setting.
VL-A110U/UC VL-AH130U < Adjusting the video/LCD section > • Measuring instruments: *Color monitor TV set *Digital voltmeter *DC power supply *Audio generator (CR oscillator) *Alignment tape (JiGWR5-5NSP) (JiGWR5-8NSE) *Oscilloscope *Frequency counter *Signal generator *AV output cable (accessory) *Video recording tape (For Y/C, audio and servo adjustments) *DC cable (AC adapter accessory) *Video extension cables *Vector scope *AC adapter 6-3-2. Servicing the VCR section Adjustment 6-3-2-1.
VL-A110U/UC VL-AH130U • Types of test modes TEST No. 1 3 Title Sensors off Contents All sensors but the cassette controller switch, dew sensor and battery sensor stay off. Battery sensor’s input voltage put in memory. Automatic battery sensor adjustment Battery adjustment error display Battery sensor’s adjustment errors are displayed at the right of the “past errors” area.
VL-A110U/UC VL-AH130U 6-3-2-3. Battery shut-off voltage adjusting method 1) 2) 3) 4) 5) 6) Supply power to the main unit, using the variable-voltage DC power supply (range of 2.5V to 5.0V). Set the CAM/OFF/VCR SW to CAM to switch to the camera mode. Load a recordable tape and set the main unit to CAM REC. PAUSE. Set the main unit to TEST mode No. 3, and start recording. Measure voltage between TL2911(+) and TL2914(GND), and adjust the supply voltage to 3.1V.
VL-A110U/UC VL-AH130U 6-3-3-1. Adjusting the power circuit 6-3-3. Adjusting the VCR circuit • Test Points on the Video Circuit Board a) POWER CIRCUIT ADJUSTMENT PROCEDURE Turn on power û 1. Adjust to CAM 15V û 2. Check P-CON 4.9V û 3. Check P-CON 3.3V û 4. Check P-CON 3.1V û 5. Check DSP 2.5V û 6. Check DSP 1.8V û 7. Check LCD 13.2V û 8. Check LCD 7V û 9. Check LCD -15.2V û 10. Check CAM -8V û Æ Turn off power.
VL-A110U/UC VL-AH130U 6-3-4. Adjustment of system controller and servo circuit 6-3-4-1. Adjustment of playback switching point Measuring instrument Oscilloscope b) CHARGING CIRCUIT ADJUSTMENT PROCEDURE Mode Playback 1) Play back the alignment tape (JiGWR5-5NSP) 2) Press the “CONTINUOUS PUSH” and “TEST MODE SELECAdjustment address 30h TION” of adjustment remote controller to set the test mode. Tape Alignment tape (JiGWR5-5NSP) (At this time the numeral of “TEST01” blinks.
VL-A110U/UC VL-AH130U 6-3-6. Adjustment of audio circuit 1. Adjustment of filter f0 Measuring instrument Oscilloscope Mode PB Input signal (tape) JiGWR5-5NSP Measuring terminal TL605/AUDIO.OUT Adjustment address 33 Set value Clear the waveform 1) Set the alignment tape (JiGWR5-5NSP). 2) Using the adjustment remote controller (RRMCG0033TASA), set the VCR adjustment mode, and set the address “33” with the operation switch (FF/REWIND key). 3) Play back the standard tape.
VL-A110U/UC VL-AH130U 5. VCO adjustment Measuring point Address Mode Adjusting method TL3802 03E VCR 1) Connect TL3803 to GND. 2) Connect the frequency counter to TL3802, and adjust the frequency. Adjustment standard 15.734kHz ± 100Hz Remarks ——————— 6. H-position adjustment Measuring point TL3802 Address 03B Mode VCR Adjusting method 1) Connect the oscilloscope to TL3802, and adjust the pulse width. t V Adjustment standard 2.8µsec ±0.15µsec Remarks ——————— 7.
VL-A110U/UC VL-AH130U 6-4. ADJUSTMENT OF CAMERA SECTION 6-4-1. Servicing of camera section (1) Object, measuring instrument and jigs necessary for camera section servicing • • • • • Gray scale chart Vectorscope Extension cable Oscilloscope Video output cable • Color bar chart • Color temperature conversion filter HOYA "LB-165" • Digital voltmeter • • • • Halogen light (2 pcs.) Color video monitor AC adapter Service Remote Control Configuration 1. Name 2. Part No. 3.
VL-A110U/UC VL-AH130U 6-4-2-1. Checking the power supply voltage • Measuring terminal: P-CON 4.9V P-CON 3.1V CAM 15V CAM -8V LENS 5.7V • Measuring instrument: Digital voltmeter 6-4-2-2. Auto focus adjustment • Basic iris adjustment Measuring instrument None DATA Adjustment Subject — 09 Hall offset Tape — 0A Iris offset Test point None 0B Iris close Adjustment address 71 Adjustment level 09, 0A, 0B 1) Set up the auto focus adjustment mode.
VL-A110U/UC VL-AH130U R-Y 4. White balance adjustment Measuring instrument Vector scope Subject Gray scale Tape — Test point VIDEO OUT (Terminated in 75 Ω) Adjustment address R-W/B 00, B-W/B 02 Adjustment level R-W/B 0 % ± 3 % B-W/B 0 % ± 3 % Spot B-Y Center point 1) Adjust the spot to the center of vector scope (R-Y : 0%, B-Y : 0%) using address 00 and 02. 5.
VL-A110U/UC VL-AH130U 6-5. TROUBLE SHOOTING 6-5-1. Classification of troubles No function at all Check the Power circuit and system control circuit. û YES Check the system control and loading motor circuit. û YES Check the inverter transformer and power circuit. û YES * Check the camera section and Y/C circuit and LCD circuit. û YES Check the Y/C circuit and head amplifier circuit. û YES Check the Y/C circuit and head amplifier circuit. û YES Check the Y/C circuit and head amplifier circuit.
VL-A110U/UC VL-AH130U 6-5-2. Troubleshooting for the camera section No picture Check the lens drive circuit (IC551) and main signal line. û YES Check IC401 (DSP), and their peripherals. û YES Check IC706 (System/Servo Control), IC551 (Lens driver) and its peripherals. û YES Check IC706 (System/Servo Control), IC551 (Lens driver) and their peripherals. û YES Check IC706 (System/Servo Control), IC551 (Lens driver) and their peripherals.
VL-A110U/UC VL-AH130U 7. SYSTEM BLOCK DIAGRAMS BATTERY NONREGE IC900 POWER (CAMERA) IC701 3.0V Reg Power Control IC POWER (SYS 3.0V) IC706 POWER (AT 3.
Lens TG V øV 38 23 2 12 13 24 15 10 1 2 23 TL165 TL166 TL177 TL174 39 IC151 10 bit ADC IC11 V-DRIVER IC101 10 Q409 131 130 15 11 129 12 18 IC707 OSD 128 16 127 17 CCD14CK TL407 79 69 23 IC601 BF Q410 FL ACC FL REC FM 101 LCD B 103 LCD R 107 LCD G 115 EQ Q8404 Q8401 FL Q8402 PEAKING AMP 8 BIN 6 RIN EQ BUF Q6451 BUF IC1451 DRIVER 5 Q307 TL3815 TL3814 TL3813 30 32 7 9 24 23 18 17 IC301 H/A 11 10 9 REC RF-OUT CN9401 28 27 11 13 14 BU
Q307 39 BUF SC305 10 ROT ERASE (A),(B) Q302 5 SC305 22 D.O. PULSE SC305 34 REC RF 7 9 16 AGC IN SC305 SC305 19 PB Y FM 30 31 REC-C 2 4 3 11 32 Q315 Q315 BUF SC305 28 REC-Y SC305 24 H-SW-P SC305 23 OVER-P SC305 13 PB RF EVN. SC305 25 AV REC-H PB REC VGC VCC DOC 9 AGC Y AMP FF30 28 27 13 RECORDING AMPLIFIER CH-2 IC 301 HEAD AMP-PROCESS a 14 RECORDING AMPLIFIER CH-1 PLAYBACK AMPLIFIER CH-2 PLAYBACK AMPLIFIER CH-1 4.
CH4 output Drive circuit (Rise and fall voltage) CH5 output Drive circuit (Voltage drop) CH4 ERROR AMP. IN- Comparator section CH5 ERROR AMP. IN- Comparator section 3 4 5 40 8 Standard power CH8 ERROR AMP. IN- Comparator section IN+ 7 B/L CTL CH7 ERROR AMP. IN- Comparator section IN+ CAP ERROR 6 CH8 output Drive circuit (NPN) CH7 output Drive circuit (Rise and fall voltage) CH6 output Drive circuit (Voltage drop) CH3 output Drive circuit (Rise and fall voltage) CH3 ERROR AMP.
LED Green DC JACK input 41 LED_R LED_G LED Red Charging : Red light up Completion : Green light up with JACK : OPEN with out JACK : GND Short circuit VDC<8V Voltage detective circuit 1 SW1 EXT Vcc 2 SW2 Charge control IC 7 8 Q2901 CS 5 3 LV 4 GND MM1332G CEL 6 ADP-DET Q2903 NON REG T PRE-CHARGE-ON CHARGE-ON_H Ni-MH battery BATT.-DET Q2903 with FET always is "OFF" at DC input.
VL-A110U/UC VL-AH130U 7-5. LENS DRIVE BLOCK DIAGRAM IC1 CCD SENSER ZOOM LENS MASTER LENS IC101 CDS AGC IC151 A/D IC401 DSP 42 41 DATA 49 48 LENS DATA2 CS 2 12 IC706 SYSCON DATA CLK IRIS, FOCUS, ZOOM CONTROL 3 4 124 Master Lens POSI 21 IRIS METER IC553 4.
VL-A110U/UC VL-AH130U -MEMO- 43
VL-A110U/UC VL-AH130U 8. SCHEMATIC DIAGRAMS 8-1.
VL-A110U/UC VL-AH130U 8-2.
VL-A110U/UC VL-AH130U 8-3.
VL-A110U/UC VL-AH130U 8-4.
VL-A110U/UC VL-AH130U 8-5.
VL-A110U/UC VL-AH130U 8-6.
VL-A110U/UC VL-AH130U 8-7.
VL-A110U/UC VL-AH130U 8-8.
VL-A110U/UC VL-AH130U 8-9.
VL-A110U/UC VL-AH130U 8-10.
VL-A110U/UC VL-AH130U 8-11.
VL-A110U/UC VL-AH130U 8-12.
VL-A110U/UC VL-AH130U 8-13.
VL-A110U/UC VL-AH130U 8-14.
VL-A110U/UC VL-AH130U 8-15.
VL-A110U/UC VL-AH130U 8-16.
VL-A110U/UC VL-AH130U 8-17.
VL-A110U/UC VL-AH130U 8-18.
VL-A110U/UC VL-AH130U 8-19.
VL-A110U/UC VL-AH130U 9.
VL-A110U/UC VL-AH130U VCR PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 83 7 8 9 10
VL-A110U/UC VL-AH130U VCR PWB Component Side SIDE B J D2912 Q2905 D901 C907 Q907 D2913 D903 FB151 C916 C920 Q911 R151 SC151 R152 L920 L926 L923 R1963R1965 C1929 R1942 R168TL170 R1956 TL174 R195 R170TL172 C164 R196 R1939 TL178 R173TL177 R186 C1912 TL181 TL188 R179 R180TL182 R182 TL184 R183 TL3801 TL185 TL1801 R930 TH3800 TL915 R931 C946 C952 IC904 R3806 R3805 C3818 C3817 R3853 C3819 R729 R713 R728 R712 R727 R711 R726 R710 R725 R709 R724 R708 R723 R707 R74
VL-A110U/UC VL-AH130U VCR PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 85 7 8 9 10
VL-A110U/UC VL-AH130U CAMERA PWB Component Side SIDE A J TL556 TL557 TL559 TL560TL565 TL566 TL567 TL568 TL570 P101 I Z1 TL100 C111 C113 L101 C108 TL101 SC551 H TL551 TL553 TL555 TL11 TL12 TL13 TL14 TL15 C563 TL25 TL29 SC102 R142TL130 TL127 R139 TL126 R138 R137 TL125 R135TL123 R132 TL120 R131TL119 R129 TL117 R128TL116 TL115 TL113 TL111 TL121 TL128 R140 R134 R133 R127 C38 L13 TL122 R123 TL112 TL31TL30 TL114 L12 R27 R28 C25 R31 R29 TL105 FB103 R109 R41 C35 TL129 TL124 R36 R
VL-A110U/UC VL-AH130U CAMERA PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 87 7 8 9 10
VL-A110U/UC VL-AH130U CAMERA PWB Component Side SIDE B J R581 R588 R576 C574 C568 R563 TL136 R148 TL135 IC553 R147 C106 C110 C112 C109 R106 C107 C103 R101 R102 R122 TL102 TL148R120 C553 C104 R103 R105 R104 C105 TL149R121 TL150 R107 R108 C573 R572 R585 C571 R586 R579 R587 R561 R564 R577 D551 C567 G R570 C566 R569 R562 R571 C572 R568 C569 R567 R566 R565 IC552 R578 C570 R575 R584 H P102 R583 R582 R580 I IC101 IC554 R589 TL147R119 TL143R115 C102 C101 C120 C15 C119 C11
VL-A110U/UC VL-AH130U CAMERA PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 89 7 8 9 10
VL-A110U/UC VL-AH130U HEAD AMP PWB Component Side SIDE A C3707 C3708 J TL3705 C3713 C3716 C3717 IC3701 C3720 TL3732 C3725 C3727 TL3733 C3726 C3729 TL3701 TL3734 R3729 TL3725 TL3716 R3727 R3726 TL3727 TL3729 TL3728 TL3738 TL3736 TL3723 R3724 R3728 R3725 C3732 TL3724 TL3706 TL3717 G C3733 TL3719 C3730 C3731 R3719 R3723 C3728 TL3718 C3723 TL3726 C3724 C3734 H TL3702 L3701 L3702 R3720 C3718 C3719 C3722 C3721 R3721 R3722 C3714 C3710 C3715 TL3721 C3711 C3705 TL3722
VL-A110U/UC VL-AH130U HEAD AMP PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 91 7 8 9 10
VL-A110U/UC VL-AH130U HEAD AMP PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 92 7 8 9 10
VL-A110U/UC VL-AH130U Part No. ★ Description Code 10.REPLACEMENT PARTS LIST/ EXPLODED VIEWS Ref. No. Ref. No. Part No. ★ Description Code DUNTK2949QA00(VL-AH130U) DUNTK2949QA03(VL-A110U/UC) VCR UNIT ELECTRICAL PARTS LIST INTEGRATED CIRCUITS Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
VL-A110U/UC VL-AH130U Ref. No. Part No.
VL-A110U/UC VL-AH130U Ref. No. L7404 L7405 L7406 L7407 L7408 L7452 L7453 L8401 L8402 L8404 L8405 L8451 L8452 å T901 ★ Part No. VPBBM471J310N VPD9M181J190N VPBBM331J260N VPD9M330J3R6N VPBBM331J260N VPD9M8R2J2R0N VPD9M8R2J2R0N VPD9M1R8JR84N VPD9M2R2JR96N VPD9M221J210N VP-1M391J330N VPD9M820J9R5N VPD9M221J210N RTRNZ0154TAZZ Code Ref. No. Part No. Peaking, 470µH Peaking, 180µH Peaking, 330µH Peaking, 33µH(AH130U) Peaking, 330µH Peaking, 8.2µH Peaking, 8.2µH(AH130U) Peaking, 1.8µH Peaking, 2.
VL-A110U/UC VL-AH130U Ref. No. C738 C750 C800 C801 C803 C804 C805 C900 C901 C902 C903 C904 C905 C906 C907 C909 C910 C912 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 C925 C926 C927 C930 C931 C932 C933 C934 C935 C936 C937 C938 C939 C940 C941 C942 C943 C944 C945 C946 C947 C948 C952 C953 C955 C956 C1401 C1405 C1406 C1407 C1408 C1415 C1416 C1451 C1452 C1453 C1454 C1456 C1458 C1459 C1801 C1803 C1805 C1806 C1808 C1809 C1810 Part No.
VL-A110U/UC VL-AH130U Ref. No. ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R753 R755 R756 R757 R758 R759 R760 R761 R762 R763 R765 R766 R767 R768 R769 R772 R773 R774 R775 R776 R777 R778 R779 R780 R781 R785 R786 R787 R788 R789 R790 R791 R792 R793 R794 R795 R797 R798 R799 R801 R802 R803 R902 R903 R904 R905 R907 R908 R911 R912 R913 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 Part No.
VL-A110U/UC VL-AH130U Ref. No. R1926 R1927 R1929 R1930 R1931 R1932 R1933 R1934 R1935 R1936 R1937 R1938 R1939 R1940 R1941 R1942 R1943 R1944 R1945 R1946 R1947 R1948 R1949 R1950 R1951 R1952 R1953 R1955 R1956 R1957 R1959 R1960 R1961 R1962 R1963 R1965 R1966 R1967 R1968 R1970 R1972 R1973 R1974 R1975 R1976 R1980 R1981 R1982 R2402 R2403 R2404 R2405 R2406 R2407 R2408 R2409 R2410 R2411 R2412 R2413 R2414 R2415 R2416 R2417 R2418 R2419 R2420 R2421 R2423 R2901 R2902 R2903 R2905 R2908 R2911 Part No.
VL-A110U/UC VL-AH130U Ref. No. Part No.
VL-A110U/UC VL-AH130U Ref. No. ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. R3701 R3702 R3703 R3704 R3705 R3706 R3707 R3708 R3715 R3716 R3717 R3718 R3719 R3720 R3721 R3722 R3723 R3724 R3725 R3726 R3727 R3728 R3729 R3731 R3732 R3733 ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. Part No. 204 206 207 208 209 211 212 213 214 LX-HZ3074GEFN LX-BZ3132GEFF LX-BZ3178GEZZ LX-HZ3083GEFF LX-HZ3077GEFN LX-HZ3084GEFF LX-HZ3116GEFD LX-NZ3053GEZZ LX-WZ1076GE02 215 LX-WZ1075GE02 216 XWHJZ12-02040 217 QCNW-1714TAZZ ★ Description Code Screw M1.7x5.3 S Tight Screw M1.4x1.5xD3.5 Screw M1.4x1.5xD4.0 Screw M1.4x2.5 S Tight Screw M1.4x3.0 S Tight Screw M1.4x4.0 S Tight Screw M1.4x3.2 S Tight Screw M1.4 Nut Washer D0.8xD3.0x0.2t Plastics Washer D2.1xD5.0x0.
VL-A110U/UC VL-AH130U Ref. No. Part No. ★ Description Code Ref. No. CASSETTE HOUSING PARTS 400 401 CHLDX3077GE01 MSPRT0414GEZZ Cassette Compartment Ass'y Up Main Spring Part No. ★ AY ACCESSORIES GCOVH1225TASA QCNW-1448TAZZ or QCNW-1295TAZZ RRMCG0084TASA AD RRMCG0085TASA PCOVM8016TA00 LANGK0324TAFW PFiLW0060TAZZ VHiLZ2413H5-1 DUNTK2800PM03 LX-HZ0013TAFF Dustproof Rubber CCD Retaining Plate Optical Filter CCD Sensor CCD PWB Unit Screw (1.
VL-A110U/UC VL-AH130U Ref. No. PartCHASSIS No. ★ Description VIEW Code MECHANISM EXPLODED Ref. No. ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. Part No. ★ VIEWDescription CABINET EXPLODED Code 3-2 Ref. No. k ★ Part No.
VL-A110U/UC VL-AH130U Ref. No. Ref. No. Part No. ★ CONTROL Description Code CASSETTE HOUSING UNIT EXPLODED VIEW Part No. ★ Description Code 400 401 C 401 B A 1 2 3 4 5 6 CAMERA UNIT EXPLODED VIEW 5 D 6 2 4 3 C 1 The mark must be on the face. B CCD side Lens side Mark Face the thinner part toward the lens side.
VL-A110U/UC VL-AH130U Ref. PACKING No. Part No. ★ Description 11. OF THE SET Code åUADP-0312TAZZ (AC Adapter) Ref. No. Part No.
VL-A110U/UC VL-AH130U Ref. No. Part No. ★ Description Ref. No. Code ★ Part No. Description Code COPYRIGHT C 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
