VL-A10U/UC/UA/UW/T/K VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-AH30U/UC/T VL-E990E SERVICE MANUAL S10U5VL-AH30U LIQUID CRYSTAL CAMCORDER Hi 8 NTSC SERVICE MANUAL VL-A10U/UC/UA/UW VL-A10T/K MODELS VL-AH30U/UC/T LIQUID CRYSTAL CAMCORDER Hi 8 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS NTSC MODELS VL-A10U/UC/UA/UW/T/K/AH30U/UC/T Page 1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E 1. IMPORTANT SERVICE NOTES connections, metal cabinet, screw heads, knobs and control shafts, etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug (a non polarized adaptor plug must be used but only for the purpose of completing these checks) on the set and repeat the AC voltage measurements for each exposed metallic part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E WARNING :TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO WET LOCATIONS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol mark means following. Camcorder only For continued protection against fire hazard, replace only with same type fuse. (CP901; 2.5A 64V, CP902; 2.5A 64V, CP903; 2.5A 64V) CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER·SERVICEABLE PARTS INSIDE.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E CAUTION BEFORE BATTERY DESTROY NICKEL-CADMIUM BATTERY The following program is available in the United States. Please consult local environmental authorities concerning the availability of this or other programs in your area. The RBRCTM Seal SHARP participates in the RBRCTM* Nickel-Cadmium Battery Recycling Program in the United States.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E 2. SPECIFICATIONS Signal System: Recording System: Cassette: Recording/Playback Time: Tape Speed: Pickup Device: Lens: Lens Filter Diameter: Monitor: Microphone: Color Temperature Compensation: Minimum Illumination: Video Output Level: Audio Output Level: Speaker Output: Power Requirement: Power Consumption: Operating Temperature: Operating Humidity: Storage Temperature: Dimensions (approx.): Weight (approx.
Speaker Microphone 6 Cassette compartment door Lens hood Remote sensor Rear view LCD monitor screen Battery compartment door Tripod socket Battery compartment door release DISPLAY button Power switch (CAMERA/VCR select switch) Hand strap FADE button Shoulder strap loop Power Zoom Wide angle/ Telephoto control VOLume control RECord START/STOP button Operation buttons Bottom view MENU button CHARGE indicator Lithium battery holder Shoulder strap loop Cassette compartment door release
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E 4. DISASSEMBLY OF THE SET 4-1. REMOVAL OF THE CAMERA SECTION Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery has been removed. (b) Connector (b) Pull out (a) (1) Camera front cabinet (d) (a) 5. Remove the connector of the 6-cell detection switch, and remove two screws ((b)LX-HZ0018TAFF) fixing the battery catcher. 1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E 4-2. DISASSEMBLY OF THE VCR MAIN BODY <1. Removal of the VCR lid shaft> Area A (b) (k) (2) Remove five screws ((b)LX-HZ0018TAFF). (1) Remove one screw ((k)LX-HZ0063TAFC).
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E <3. Removal of the VCR lid> Caution for installation of the VCR lid Microphone connector VCR lid Area B When installing the VCR lid, move the VCR lid in the arrow direction, keeping the VCR lid parallel to the main body as shown above. (1) Disconnect the microphone connector. <4.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E <8. Removal of the Lithium PWB> (b) LCD unit Lithium PWB Main PWB Connector Connector Inverter transformer (3) Remove two screws ((b)LX-HZ0018TAFF) and two connec- (1) Remove the connector of the Lithium PWB from the Main PWB. tors, and remove the LCD unit (with inverter) from the main (2) Move the lithium unit in the direction of the arrow. body. <9. Disassembly of the frame V> <6.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Claw C Claw B View E Claw A Claw D View F Note: When fixing the cassette compartment lid, first engage the claws A and B, and then engage the claws C and D, verify that the four claws (A, B, C and D) of the cassette compartment lid are securely engaged as shown in the view above. <11.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E 4-3. REPLACEMENT OF CCD SENSOR 4-3-1. BEFORE REPLACEMENT 1) The CCD image sensor is more sensitive to electrostatic breakage than C-MOS LSI. Therefore sufficient means to prevent electrostatic damage must be taken when it is replaced. • Ground the soldering iron. • Ground also the human body, using the wrist strap(through an 1 Mohm resistor). • Until the CCD sensor is mounted on the PWB, fit it to the conductive sponge, and short-circuit the foot lead.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5. MECHANISM ADJUSTMENT 5-1. MECHANISM CHECKING/ADJUSTING JIGS, TOOLS AND PARTS 5-1-1. Mechanism checking/adjusting jigs and tools 1. Cassette torquemeter for PB 2. JiG8T-012 3. CV * (10 g·cm/25 g·cm) 1. Cassette torquemeter for VS-REW 2. JiG8T-032 3. CV * (50 g·cm/25 g·cm) 1. Torque gauge 2. JiGTG0045 3. CN * For measurement of loading brake torque Configuration 1. Name 2. Part No. 3. Code * Model, Uses Remarks 1. Torque gauge head 1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-2. ITEMS AND TIMINGS OF INSPECTION AND MAINTENANCE The mechanism of VCR needs the following periodic inspection and maintenance in order that it maintains its high quality. Also, after the machine is repaired, execute the following maintenance and checks regardless of how long it has been used. 5-2-1. Inspection and maintenance list Checking/Maintenance point 500 Usage time (hrs.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-3. MECHANISM CHECKS AND ADJUSTMENTS The description given below relates to the general field services, but does not relate to the adjustment and replacement that require high level equipments, jigs, and technical skills. In order to maintain the initial characteristics of the machine, it is necessary to execute the maintenance and check and to prevent damage to tapes and other parts. For adjustments which need jigs, be sure to use the jigs.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-3-4. Checking and adjusting the tension pole position (1) Check When winding of P6-120 tape is started, check whether the tension pole is in the specified position against Si roller as shown or not. If it is not in the specified position, remove the cassette and adjust the position in the following procedure. (2) Adjustment 1. Don’t set up any tape, and select the PB mode. (Refer to Item 5-5-1-(4).) 2.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-4. ADJUSTMENT OF MECHANISM TAPE TRAVEL SYSTEM Sup tilted pole 5-4-1. Preparation for adjustment Sup GR (1) Clean the tape running areas (guide poles, rollers, drum, Capstan shaft, Pinch roller) (Figure 1) Si roller (2) Connect the oscilloscope to the following TPs. RF output ..... TL7410 H-SW-P ....... TL7417 GND ............. TL7413 (3) Playback the alignment tape (VR2ABOPS). Tension pole (4) Ascertain that each guide is free from remarkable curl.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-4-4. Adjusting the Tu guide Height setting jig Master plane (JiGMP-MX7U) Upper flange After replacement of Tu guide preset and adjust the height. (1) Tu guide height presetting (Figure 6) Adjust the height from the upper surface of mechanism chassis to the upper surface of lower flange with the aid of jig. Lower flange Figure 6 (2) Adjusting the Tu guide (Figure 7) 1 Playback the alignment tape (VR2ABOPS).
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-5. MECHANISM ASSEMBLING AND PARTS REPLACEMENT (DISASSEMBLING AND ASSEMBLING) Below is given an explanation of assembling of mechanism and its parts replacement. The removal of cabinet and Circuit Board is explained in the relevant service manual. Notes 1 After removal of cut washers be sure to replace them with new ones. 2 Do not place the mechanism upside down on the table. Otherwise, the mechanism part may be deformed or damaged, resulting in malfunction.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5-5-2. Cassette control ass’y Lock Lever (1) Set the unit to the EJECT mode, and let the housing stand upright. Or set the unit to the STANDBY mode, press the lock lever in the arrow direction, and let the housing stand upright. (See Fig. 5: in the direction a or b ) (When pushing in the direction a , slightly lift the housing by hand to release the lock lever.) (2) Remove the four screws 2 and take out the down guide 3.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T (3) Upper drum ass’y (Both common type) Remove the upper drum ass’y from the lower drum ass'y as shown in Figure 3. At this time take care so as not to lose the gap shim. (4)-a Motor rotor ass'y and rotary transformer rotor ass'y(former type) Remove the 2 rotor mounting screws as shown in Figure 4-a, and remove the motor rotor and the rotary transformer ass'y.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T (3) Lower drum ass'y Tighten the FPC mounting screw to the lower drum ass'y. The screw tightening torque must be 0.08N·m (tighting torque 0.8kg·cm). (Figure 6) (4) Upper drum ass’y After fitting the gap shim which was removed when the upper drum ass'y was dismantled to the shaft of lower drum ass’y, fit the upper drum ass’y. (Figure 3) At this time slightly turn the upper drum ass'y by hand to ascertain that RTr does not scrape.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T (7) Install the guide rail assembly taking care to position it (4) Install the loading block assembly and the capstan motor. correctly. (5) Install the drive gear. At this time, pay attention to the direction of gear. (The small gear must be located in the B A chassis side.) a a A a Make sure not deform the arm. Loading motor Capstan motor a A a D C Move FF downwards Install the motor under this plate.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T (8) Install the drum assembly in the chassis. (9) Install the tape guide in the drum assembly. (10) Install the Si roller. (11) Install the slide chassis. T arm guide B Tape guide A Slide this part towards the T arm. Place the slide chassis on the guide rail. A Drum assembly B A A Si roller B Roller spring Main cam pin B Insert the main cam pin into the hole of cam of slide chassis. Sup reel base Item A M1.4 x 1.5 ø4 B M1.4 x 1.5 ø3.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6. ADJUSTMENT OF VCR AND CAMERA 6-1. INITIAL SETTING OF E2PROM IC 6-1-1. E2PROM data alterable ways 1) Set the switch of main body to CAM, and use the remote control (RRMCG0033TASA) for adjustment to turn on the adjustment mode. 2) VCR adjustment address setting. V ADJ 0000 “0000” is blinking After an objective address was established, play key is pushed and set. In addition, numerical change uses a “REW” or “FF” key. 3) VCR adjustment data setting.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T < Adjusting the video/LCD section > • Measuring instruments: *Color monitor TV set *Digital voltmeter *DC power supply *Audio generator (CR oscillator) *Alignment tape (JiGWR5-5NSP) (JiGWR5-8NSE) *Oscilloscope *Frequency counter *Signal generator *AV output cable (accessory) *Video recording tape (For Y/C, audio and servo adjustments) *DC cable (AC adapter accessory) *Video extension cables *Vector scope *AC adapter 6-3-2. Servicing the VCR section Adjustment 6-3-2-1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T • Types of test modes TEST No. 1 3 Title Sensors off Contents All sensors but the cassette controller switch, dew sensor and battery sensor stay off. Battery sensor’s input voltage put in memory. Automatic battery sensor adjustment Battery adjustment error display Battery sensor’s adjustment errors are displayed at the right of the “past errors” area.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-3-2-3. Battery shut-off voltage adjusting method 1) 2) 3) 4) 5) 6) Supply power to the main unit, using the variable-voltage DC power supply (range of 2.5V to 5.0V). Set the CAM/OFF/VCR SW to CAM to switch to the camera mode. Load a recordable tape and set the main unit to CAM REC. PAUSE. Set the main unit to TEST mode No. 3, and start recording. Measure voltage between TL2911(+) and TL2914(GND), and adjust the supply voltage to 3.1V.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-3-3-1. Adjusting the power circuit 6-3-3. Adjusting the VCR circuit • Test Points on the Video Circuit Board a) POWER CIRCUIT ADJUSTMENT PROCEDURE Turn on power û 1. Adjust to CAM 15V û 2. Check P-CON 4.9V û 3. Check P-CON 3.3V û 4. Check P-CON 3.1V û 5. Check DSP 2.5V û 6. Check DSP 1.8V. û 7. Check LCD 13.2V û 8. Check LCD 7V û 9. Check LCD -15.2V û 10. Check CAM -8V û Æ Turn off power.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-3-4. Adjustment of system controller and servo circuit 6-3-4-1. Adjustment of playback switching point Measuring instrument Oscilloscope b) CHARGING CIRCUIT ADJUSTMENT PROCEDURE Mode Playback 1) Play back the alignment tape (JiGWR5-5NSP) 2) Press the “CONTINUOUS PUSH” and “TEST MODE SELECAdjustment address 30h TION” of adjustment remote controller to set the test mode. Tape Alignment tape (JiGWR5-5NSP) (At this time the numeral of “TEST01” blinks.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-3-6. Adjustment of audio circuit 1. Adjustment of filter f0 Measuring instrument Oscilloscope Mode PB Input signal (tape) JiGWR5-5NSP Measuring terminal TL605/AUDIO.OUT Adjustment address 33 Set value Clear the waveform 1) Set the alignment tape (JiGWR5-5NSP). 2) Using the adjustment remote controller (RRMCG0033TASA), set the VCR adjustment mode, and set the address “33” with the operation switch (FF/REWIND key). 3) Play back the standard tape.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 5. VCO adjustment Measuring point Address Mode Adjusting method TL3802 03E VCR 1) Connect TL3803 to GND. 2) Connect the frequency counter to TL3802, and adjust the frequency. Adjustment standard 15.734kHz ± 100Hz Remarks ——————— 6. H-position adjustment Measuring point TL3802 Address 03B Mode VCR Adjusting method 1) Connect the oscilloscope to TL3802, and adjust the pulse width. t V Adjustment standard 2.8µsec ±0.15µsec Remarks ——————— 7.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-4. ADJUSTMENT OF CAMERA SECTION 6-4-1. Servicing of camera section (1) Object, measuring instrument and jigs necessary for camera section servicing • • • • • Gray scale chart Vectorscope Extension cable Oscilloscope Video output cable • Color bar chart • Color temperature conversion filter HOYA "LB-165" • Digital voltmeter • • • • Halogen light (2 pcs.) Color video monitor AC adapter Service Remote Control Configuration 1. Name 2.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-4-2-1. Checking the power supply voltage • Measuring terminal: P-CON 4.9V P-CON 3.1V CAM 15V CAM -8V LENS 5.7V • Measuring instrument: Digital voltmeter 6-4-2-2. Auto focus adjustment • Basic iris adjustment Measuring instrument None DATA Adjustment Subject — 09 Hall offset Tape — 0A Iris offset Test point None 0B Iris close Adjustment address 71 Adjustment level 09, 0A, 0B 1) Set up the auto focus adjustment mode.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T R-Y 4. White balance adjustment Measuring instrument Vector scope Subject Gray scale Tape — Test point VIDEO OUT (Terminated in 75 Ω) Adjustment address R-W/B 00, B-W/B 02 Adjustment level R-W/B 0 % ± 3 % B-W/B 0 % ± 3 % Spot B-Y Center point 1) Adjust the spot to the center of vector scope (R-Y : 0%, B-Y : 0%) using address 00 and 02. 5.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-5. TROUBLE SHOOTING 6-5-1. Classification of troubles û YES Check the Power circuit and system control circuit. û YES Check the system control and loading motor circuit. û YES Check the inverter transformer and power circuit. û YES * Check the camera section and Y/C circuit and LCD circuit. û YES Check the Y/C circuit and head amplifier circuit. û YES Check the Y/C circuit and head amplifier circuit. û YES Check the Y/C circuit and head amplifier circuit.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 6-5-2. Troubleshooting for the camera section û YES Check the lens drive circuit (IC551) and main signal line. û YES Check IC201 (DSP), and their peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and its peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and their peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and their peripherals.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-H875T VL-H890T 7. SYSTEM BLOCK DIAGRAMS BATTERY NONREGE IC900 POWER (CAMERA) IC701 3.3V Reg Power Control IC POWER (SYS 3.3V) IC706 POWER (AT 3.
Lens TG V øV 39 23 2 12 13 24 15 10 1 2 23 TL165 TL166 TL177 TL174 39 IC151 10 bit ADC IC11 V-DRIVER IC101 10 Q409 131 130 15 11 129 12 18 IC707 OSD 128 16 127 17 CCD14CK TL407 79 69 23 IC601 BF Q410 FL ACC FL REC FM 101 LCD B 103 LCD R 107 LCD G 115 Q8401 Q8402 EQ Q8404 FL PEAKING AMP 8 BIN 6 RIN BUF Q6451 BUF IC1451 DRIVER 5 Q307 TL3815 TL3814 TL3813 30 32 7 9 24 23 18 17 IC301 H/A 11 10 9 REC RF-OUT CN9401 28 27 11 13 14 BUF 1
Q307 40 BUF SC305 10 ROT ERASE (A),(B) Q302 5 SC305 22 D.O. PULSE SC305 34 REC RF 7 9 16 AGC IN SC305 SC305 19 PB Y FM 30 31 REC-C 2 4 3 11 32 Q315 Q315 BUF SC305 28 REC-Y SC305 24 H-SW-P SC305 23 OVER-P SC305 13 PB RF EVN. SC305 25 AV REC-H PB REC VGC VCC DOC 9 AGC Y AMP FF30 28 27 13 RECORDING AMPLIFIER CH-2 IC 301 HEAD AMP-PROCESS a 14 RECORDING AMPLIFIER CH-1 PLAYBACK AMPLIFIER CH-2 PLAYBACK AMPLIFIER CH-1 4.
CH4 output Drive circuit (Rise and fall voltage) CH5 output Drive circuit (Voltage drop) CH4 ERROR AMP. IN- Comparator section CH5 ERROR AMP. IN- Comparator section 3 4 41 8 Standard power CH8 ERROR AMP. IN- Comparator section IN+ B/L CTL CH7 ERROR AMP. IN- Comparator section IN+ 7 CAP ERROR 6 DRUM ERROR CH8 output Drive circuit (NPN) CH7 output Drive circuit (Rise and fall voltage) CH6 output Drive circuit (Voltage drop) CH3 output Drive circuit (Rise and fall voltage) CH3 ERROR AMP.
LED Green DC JACK input 42 LED_R LED_G LED Red Charging : Red light up Completion : Green light up with JACK : OPEN with out JACK : GND Short circuit VDC<8V Voltage detective circuit 1 SW1 EXT Vcc 2 SW2 Charge control IC 7 8 Q2901 CS 5 3 LV 4 GND MM1332G CEL 6 ADP-DET Q2903 NON REG T PRE-CHARGE-ON CHARGE-ON_H Ni-MH battery BATT.-DET Q2903 with FET always is "OFF" at DC input.
VL-H875T VL-H890T VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 7-5. LENS DRIVE BLOCK DIAGRAM IC1 CCD SENSER ZOOM LENS MASTER LENS IC101 CDS AGC IC151 A/D IC401 DSP 42 41 DATA 49 48 LENS DATA2 CS 2 12 IC706 SYSCON DATA CLK IRIS, FOCUS, ZOOM CONTROL 3 4 124 Master Lens POSI 21 IRIS METER IC553 4.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8. SCHEMATIC DIAGRAMS 8-1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-2.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-3.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-4.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-5.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-6.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-7.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-8.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-9.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-10.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-11.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-12.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-13.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-14.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-15.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-16.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-17.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-18.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 8-19.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 9.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 93 81 73 61 51 41 37 33 29 25 19 A 138 120 108 90 75 60 54 48 42 36 27 J C EX0161TA EX0210TA EX0870CE HVU362 KV1812K FS1J2E MA729 MA2S111 F1J2H HVU350B I HVU359TR F02J9 H 64 44 38 30 28 24 20 16 14 10 IX0616TA 32 22 19 15 14 12 10 8 7 5 G 28 37 43 49 55 61 76 91 109 121 139 F CXA2096N MS548331 MM1323XV BU4051FV LA7473V PCMB3006T M40C558V T7A164S UPD16510 LB11952W IX0759TA BA7761KV BH7273KV LR38610 BH7272KV MB88344F UPC2391G LB1990W MM1449XQ MB86611 C111306F I
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T 10.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VCR PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 85 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VCR PWB Component Side SIDE B J I D2913 D903 FB151 C916 C920 Q911 C943 FB152 R151 C917 D902 C948 Q925 TL153 TL9716 SC151 L920 L926 L923 R1963R1965 R1952R1953 C1929 R1942 R196 C164 R173TL177 TL178 R186 TL181 TL188 R179 R180TL182 R182 R183 TL185 TL1801 R930 TH3800 TL915 R931 C946 C952 IC904 R3806 R3805 C3818 R3853 C3819 R729 R713 R728 R712 R727 R711 R726 R710 R725 R709 R724 R708 R723 R707 R743 TL189 TL183 TL903 TL184 TL38
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VCR PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 87 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T CAMERA PWB Component Side SIDE A J TL556 TL557 TL559 TL560TL565 TL566 TL567 TL568 TL570 I P101 Z1 TL100 C111 C113 L101 C108 TL101 SC551 H TL551 TL553 TL555 TL11 TL12 TL13 TL14 TL15 TL562 TL564 C563 TL25 TL29 SC102 R142TL130 TL127 R139 TL126 R138 R137 TL125 R135TL123 R132 TL120 R131TL119 R129 TL117 R128TL116 TL115 TL113 TL111 TL121 TL128 R140 R134 R133 R127 C38 L13 TL122 R123 TL112 TL31TL30 TL114 L12 R27 R28 C25 R31 C TL104 FB102 R29 TL105
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T CAMERA PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 89 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T CAMERA PWB Component Side SIDE B J C574 C568 R563 R570 C566 R569 R562 IC552 TL136 R148 TL135 IC553 R147 C106 C110 C112 C109 R106 C107 C103 R101 R102 R122 TL102 TL148R120 C553 C104 R103 R105 R104 C105 TL149R121 TL150 R107 R108 C573 R572 R585 C571 R586 R579 R587 R561 R564 R577 D551 R571 C572 R568 C569 R567 R566 R565 C567 G P102 R583 R582 R580 R578 C570 R575 R584 H R581 R588 R576 I IC101 IC554 R589 TL147R119 TL143R115 F C102 C101 C120
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T CAMERA PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 91 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T HEAD AMP PWB Component Side SIDE A C3707 C3708 J TL3705 C3711 IC3701 TL3702 L3701 C3720 TL3732 R3723 C3728 TL3733 C3726 C3729 TL3719 TL3701 TL3734 R3729 TL3725 TL3716 R3727 R3726 TL3727 TL3729 TL3728 TL3738 TL3736 TL3723 R3724 R3728 R3725 C3732 TL3724 TL3706 TL3717 G C3733 C3730 C3731 TL3718 C3723 TL3726 C3724 C3734 L3702 R3720 C3718 C3719 C3722 C3721 R3721 R3722 C3716 C3717 R3719 C3705 C3702 C3703 R3701R3705R3707 R3704 R3702 C3
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T HEAD AMP PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 93 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T HEAD AMP PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 94 7 8 9 10
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Part No. ★ Description Code 11.REPLACEMENT PARTS LIST/ EXPLODED VIEWS Ref. No. Ref. No. Part No. Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. Q925 Q926 Q928 Q932 Q933 Q934 Q935 Q936 Q937 Q938 Q939 Q940 Q941 Q1401 Q1402 Q1403 Q1404 Q1406 Q1451 Q1800 Q1801 Q1802 Q2401 Q2402 Q2403 Q2405 Q2406 Q2407 Q2408 Q2901 Q2903 Q2905 Q2906 Q2907 Q2910 Q2911 Q2912 Q2913 Q2914 Q2915 Q3601 Q3602 Q3801 Q6401 Q6402 Q6404 Q6451 Q7401 Q7402 Q7403 Q7404 Q7405 Q7406 Q7407 Q7408 Q7409 Q7410 Q7451 Q7452 Q7453 Q7454 Q7455 Q8401 Q8402 Q8404 Q8405 Q8406 Q8407 Q8451 Q8452 Q8453 Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. C715 C716 C717 C718 C720 C721 C722 C724 C725 C726 C727 C728 C729 C730 C731 C732 C733 C737 C738 C750 C800 C801 C803 C804 C805 C900 C901 C902 C903 C904 C905 C906 C907 C909 C910 C912 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 C925 C926 C927 C930 C931 C932 C933 C934 C935 C936 C937 C938 C939 C940 C941 C942 C943 C944 C945 C946 C947 C948 C950 C951 C952 C953 C955 C956 C1401 Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. R8462 R8463 R8464 R8467 R9410 R9919 R9921 ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. C3705 C3706 C3707 C3708 C3709 C3710 C3711 C3712 C3713 C3714 C3715 C3716 C3717 C3718 C3719 C3720 C3721 C3722 C3723 C3724 C3725 C3726 C3727 C3728 C3729 C3730 C3731 C3732 C3733 C3734 ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. VL-E990E Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. VL-E990E Part No. ★ Description Code Ref. No. 401 402 403 CHLDX3077GE01 MSPRT0414GEZZ MROD-0014GEFJ PDMP-0013GEZZ Cassette Compartment Ass'y Up Main Spring Damper rod Cassette Compartment Damper PCOVM8016TA00 LANGK0324TAFW PFiLW0060TAZZ VHiLZ2413H5-1 DUNTK2800PM03 LX-HZ0013TAFF Dustproof Rubber CCD Retaining Plate Optical Filter CCD Sensor CCD PWB Unit Screw (1.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No. ★ Description Ref. No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No. ★ Description VIEW Code MECHANISM CHASSIS EXPLODED Ref. No. Description Code 375 200 203 200 217 H ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No. ★ CABINET EXPLODED VIEWDescription Ref. No. Code ★ Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No. ★ CONTROL Description Code Ref. No. CASSETTE HOUSING UNIT EXPLODED VIEW Part No. ★ Description Code 402 C 403 400 401 401 B A 1 2 3 4 5 6 CAMERA UNIT EXPLODED VIEW 5 D 6 2 4 3 C 1 The mark must be on the face. B CCD side Lens side Mark Face the thinner part toward the lens side.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. PACKING No. Part No. ★ Description 12. OF THE SET Ref. No. Code Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T Ref. No. Part No. VL-E990E ★ Description Code Ref. No. -MEMO- 114 Part No.
VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-E990E Ref. No. Part No. ★ Description Ref. No. Code -MEMO- 115 Part No.
VL-A10U/UC/UA/UW/T/K VL-A10U/UC/UA/UW/T/K VL-AH30U/UC/T VL-AH30U/UC/T Ref. No. Part No. VL-E990E ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT C 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
