VE-CG30U VE-CG40U SERVICE MANUAL S92Q8VE-CG30U S72M7VL-MC500 DIGITAL STILL CAMERA MODELS VE-CG30U VE-CG40U In the interests of user-safety (Required by safety regulations in some countries) the set should be resrored to its original condition and only parts identical to those specified be used. CONTENTS Page 1. IMPORTANT SERVICE NOTES ........................................................................................................ 2 2. SPECIFICATIONS ............................................
VE-CG30U VE-CG40U 1. IMPORTANT SERVICE NOTES connections, metal cabinet, screw heads, knobs and control shafts, etc.) and measure the AC voltage drop across the resistor. Reverse the AC plug (a non polarized adaptor plug must be used but only for the purpose of completing these checks) on the set and repeat the AC voltage measurements for each exposed metallic part. Any reading of 0.45V rms (this corresponds to 0.3mA rms AC.
VE-CG30U VE-CG40U ■ PRECAUTIONS FOR USING LEAD-FREE SOLDER 1) Employing lead-free solder "Main PWB", "Camera head PWB", "Audio I/O PWB", "Card PWB", "Inverter PWB", "Operation PWB", "DC Jack PWB", "CCD PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
VE-CG30U VE-CG40U 2. SPECIFICATIONS Digital still camera Image Capturing Device Operating Temperature Storage Temperature Operating Humidity 1/1.8" CCD image sensor (effective pixels: 4.04 megapixels(CG40U) 3.2megapixels(CG30U)) F2.0-F2.5 f=7-21mm (35mm film equivalent: 33-99mm) 1-3x in optical range, 3-9x in digital range Auto white balance with daylight, fluorescent or tungsten 1.5" CGSilicon, 134,000pixels AA size alkaline batteries Ni-MH rechageble batteries DC 6.0V with AC adapter 3.2W (CG40U), 2.
Tripod socket Zoom lens Flash sensor Self timer indicator Flash Microphone (CG40 ONLY) Shutter button Mode Dial Battery compartment door release Bottom view Wrist strap loop Power button Front view DC IN jack USB terminal A/V OUT jack (CG40U) VIDEO OUT jack (CG30U) Flash / Delete button Macro / Thumbnail button Speaker (CG40 ONLY) SET/DISPLAY button Data transfer button Card slot cover Power Zoom buttons (W: wide angle,T: telephoto) Diopter control Status indicator Jack cover Opera
VE-CG30U VE-CG40U 4. DISASSEMBLY OF THE SET 4-1. DISASSEMBLY OF THE SET Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery have been removed. 1. Remove the five screws ((a)LX-HZ0063TAFF) and two screws ((h)XiPSF17P04000). 4. After removing the one screw ((f)XiPSF17P03000) and one screw ((g)XiPSN17P02000), disconnect the connector and pull out the FFC to take out the LCD unit. a h FFC LCD unit h a a a a 2.
VE-CG30U VE-CG40U 8. Remove the four screws ((f)XiPSF17P03000) to take out the AV jack PWB and strobe unit. 6. Disconnect the two connectors to take out the CCD PWB. Each connector has four wires. (For 40U, disconnect the three connectors.) Caution: Hold the transformer to remove the strobe unit. Connector(CG40U only) AV jack PWB Connector Connector Transformer CCD PWB Strobe unit 7. Remove the one screw ((b)LX-HZ0050TAFF) and disconnect the connector to take out the top cabinet.
VE-CG30U VE-CG40U 4-2. REPLACEMENT OF CCD SENSOR 4-2-1. BEFORE REPLACEMENT 1) The CCD image sensor is more sensitive to electrostatic breakage than C-MOS LSI.Therefore sufficient means to prevent electrostatic damage must be taken when it is replaced. • Ground the soldering iron. • Ground also the human body, using the wrist strap(through an 1 M ohm resistor). • Until the CCD sensor is mounted on the PWB, fit it to the conductive sponge, and short-circuit the foot lead.
VE-CG30U VE-CG40U 5.TEST MODE FUNCTION [Note]: The meaning of TEST MODE FUNCTION Under this test mode, following things can be done. 1; Check and change EEPROM values, if required. 2; Apply several tests and adjustments. 3; Check the version # of firmware. How to enter the test mode (TEST MODE initial screen) Reset the user mode settings first. Download the user mode settings reset program to the SD card to create a test mode setting card. Regarding Test Mode Setting Program("Shce0009.dat" & "Shcu0009.
VE-CG30U VE-CG40U 5-1. Test mode specifications 5-1-1. TEST 0: EEPROM address change [Note]: If address is selected and the data is changed during adjustment, the data of EEPROM is rewritten, so take sufficient care for operation and never fail to take a memo of the address and the data before changing the data. When entering the test mode 0, the screen on the right appears. [Operation] 1. Move the triangle mark ( ) to the digit to be changed using the or button.
VE-CG30U VE-CG40U 5-1-3. TEST 2: User mode settings When finishing the service works, the camera must be set USER MODE again. In order to set the camera back to USER MODE, execute TEST 2 as below. [Operation] Select the TEST 2 and press the SET key. · Press the SET key start to [User Mode settings]. · When completed, the screen below appears.
VE-CG30U VE-CG40U 5-1-7. TEST 7: AF adjustment 5-1-9. TEST A: Shutter timing adjustment (open side) Select the TEST 7 and press the SET key. Select the TEST A and press the SET key.
VE-CG30U VE-CG40U 5-2. Adjustment method Jig name Part code AC adapter UADP-A013WJZZ 2 halogen lamps Commerical item Gray scale chart JiGCHART-1 Color Bar Chart JiGCHART-4 Siemens star chart JiGCHART-11 Illuminometer (0-3000 lux) JiGMETER-1 Color temperature meter (1600 - 400000K) JiGMETER-3 Color temperatute conversion filter (3200 - 6800K) JiGHOYA-LB165 HOYA "LB-165" Price code AY – CP DA CE CT FF BN Remarks
SC1002 QSOCN0672TAZZY (reverse contact) SC7201 QSOCN1872TAZZ SC1803 QSOCN0672TAZZY (reverse contact) CGS IF PWB Parts are monted on the back.
SC1002 QSOCN0672TAZZY (reverse contact) SC7201 QSOCN1872TAZZ SC1803 QSOCN0672TAZZY (reverse contact) CGS IF PWB Parts are monted on the back.
VE-CG30U VE-CG40U 5-2-1. Power circuit adjustment Conditions Mode dial setting: Measuring instrument: Adjustment jig: AUTO Digital voltmeter Dummy load is connected to each TL. Line name LCD 12.0V CAM 15.0V CAM -7.0V TL TL5904 TL1 TL3 Current 8.6mA 10.0mA 8.0mA Resistance 1.4KΩ 1.4KΩ 0.8KΩ 5-2-1-1. Power line voltage check Power line name 1.APCON 5V 2.APCON 3.3V 3.DPCON 3.3V 4.DPCON 1.8V 5.LCD 12V 6.CAM 15V 7.CAM -7.
VE-CG30U VE-CG40U 5-2-2-4. Common bias DC voltage adjustment Address: 0509 Measuring point: TL1842 TL1832 (GND) (1) Connect the digital voltmeter to TL1842. (2) Select the address 0509 and set the address. (Color Bar pattern appears onLCD Display) (3) Set the data of the DC voltage to a specified value using or key. Adjustment specification: 6.3V±0.1V 5-2-2-5. Video output level adjustment Address: 0065 Measuring point: TL407 TL411 (GND) (1) Connect the oscilloscope to TL407.
VE-CG30U VE-CG40U 5-2-3-3. Mechanical shutter open aperture adjustment/CCD sensitivity adjustment [Purpose] • Brightness of the optical system including the CCD imager is adjusted to obtain ISO100. • Operation time in the open state of the mechanical shutter aperture is memorized and the variation of exposing time is removed. [Object] • An evenly illuminated white object under the lighting described in “Preparation before adjustment and check items”.
Yes 19 FL201 or IC204(ASIC) failure. Yes Though voltage is applied to all power lines, power does not turn on (LED and LCD are not lit). Yes Is 15V applied to both ends of C5904? Is voltage (NONREG) applied to T5901 3PIN and 4PIN? Yes Yes Is 3.3V applied to TL4902 even for a moment? Yes Is 3.5V applied to both ends of C4902 even for a moment? Yes Is 1.
Yes Yes Yes 20 Yes Yes Yes No No No No No No No No No No No IC1 peripheral circuit Check periphery of IC204. IC3 failure Check IC204. Check IC2. Check L4 and L5. Check Q2 and C26. IC1 failure Check and IC2. Check IC4 and its peripheral circuit. Refer to power troubleshooting. Refer to LCD troubleshooting. IC1 corresponds to the part 103 of the Camera Exploded View on page 82. Check IC401 and its peripheral circuit.
Yes No No No No No Check IC1801 27PIN to 32PIN. Check peripheral circuit of L1802. Check SC801 on MAIN PWB and its peripheral circuit. Check FFC between MAIN PWB and LCD PWB. Refer to "Power circuit troubleshooting". Check FFC between MAIN PWB and LCD PWB. Backlight of LCD unit is defective. Yes Is 12V applied to TL1801? 21 Video/Audio cable is defective.
IC204 is defective. Is image recorded to SD card? Yes Is pulse sent from IC1602 8PIN? Yes Is audio signal sent to IC1602 3PIN? Yes Are IC1602 13PIN and 14PIN set to "H"? Yes Is 4.096MHz sent to R1637? Yes Yes Is 3.3V applied to both ends of L1602, L1603 and L1605? Is 5V applied to both ends of L1604? Set mode SW to MOVIE. Sound recording system troubleshooting Periphery of P1701 on operation PWB, FFC between operation PWB and MAIN PWB, and speaker unit are defective.
VE-CG30U VE-CG40U -MEMO- 23
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 7. BLOCK DIAGRAMS 7-1.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 7-2.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 7-3. POWER SECTION BLOCK DIAGRAM J *1: Only CG40 system for the AUDIO circuit and SP5V I DC JACK D1 AC ADAPTOR OUT: 6.0V – 7.0V (planed) Electric current rating (not yet determined) SP_5V *1 5.0V *1 REG circuit 5.5V booster circuit 5.5V Vf2 APCON_5V 5.0V REG circuit FET2 CAM 5V Vf1 FET1 OFF when the DC jack is inserted H CAM_ON + Size AA battery, 4 cells Voltage: 4.0 – 7.2V (1.0 - 1.8V per cell) CAM3.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8. SCHEMATIC DIAGRAMS 8-1.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-2.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-3.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-4.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-5.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-6.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-7.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U å AND SHADED COMPONENTS=SAFETY RELATED PARTS 8-8.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U å AND SHADED COMPONENTS=SAFETY RELATED PARTS 8-9.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-10.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-11.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-12.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-13.
VE-CG30U VE-CG40U 8-14.
VE-CG30U VE-CG40U 8-15.
VE-CG30U VE-CG40U 8-16.
VE-CG30U VE-CG40U 8-17.
VE-CG30U VE-CG40U 8-18.
VE-CG30U VE-CG40U 8-19.
VE-CG30U VE-CG40U VE-CG30U VE-CG40U 8-20.
VE-CG30U VE-CG40U 9.
VE-CG30U VE-CG40U -MEMO- 10 11 12 13 14 15 65 16 17 18 19
VE-CG30U VE-CG40U R2443 R2445 R2446 C2423 R2420 R2422 R2423 C2413 C2410 C2422 C2426 R2447 R2448 C2416 J R2424 R2425 10.
P2902 R2903 R2904 TL2911 F2902 R762 R2901 R2902 R218 IC702 IC2901 R706 R740 C3901 Q711 C6901 C3902 D3901 TL2909 Q6901 IC7901 C7902 IC701 C7901 C701 C703 R725 SC201 R710 C704 IC703 R775 TL2907 R6902 L3901 Q3901 NTL2 C702 TL2901 FB2902 R3902 R734 C705 TL2905 TL2906 TL2904 R715 R735 C716 TL2903 TL223 TL2902 FB2901 C707 R701 R204 R202 S201 R201 R769 R771 R255 C717 R7902 R708 R709 FL701 C706 R7901 R736 R765 R737 R733 R768 R774 Q710 R738 VE-CG30U VE-
VE-CG30U VE-CG40U R2425 R2424 R2423 R2422 R2420 J R2448 R2447 R2446 R2445 R2443 C2416 C2413 C2410 C2422 C2426 C2423 Z1 S204 I R773 IC2403 IC2408 C715 C46 C44 L801 L803 L802 C805 C802 R803 R806 TL808 R1013 TL1017 TL1023 TL1205 TL1203 R36 R38 C35 R19 C34 C33 C32 C31 FB8902 FB8901 C29 C28 C27 IC1201 SC1001 R20 R21 R22 R1926 R1906 C1902 R1905 C1903 R1923 R1907 C1907 R1930 R1901 TL1016 TL1204 TL1202 TL1201 C36 C1606 C21 R2 C2 Q1001 TL1024 R9905TL1025 C4 TL8 TL5901 TL22
FB2901 R204 R202 R201 P2902 R2903 F2902 D5902 R3901 L6901 C5901 T5901 C6902 R5902 L5901 L6902 SC701 C6903 C4907 Q5902 L4902 C5911 L5902 R248 R219 D5903 R4902 C4902 C5902 R1616 FB1602 R1620 TL1628 C1642 C43 R5908 P1602 R5909 L1901 C1626 C5905 Q5906 R5907 Q5903 C5909 C5913 TL4902 Q5905 C5908 R5910 R5904 R214 R215 Q5907 C5910 TL5903 Q5904 TL5904 R5912 R5913 R5914 R220 R216 R5911 R5903 R4901 D5901 C5904 Q4901 L4901 R5906 C5906 IC4902 Q5908 R5905 C4908
VE-CG30U VE-CG40U J TL1809 TL1846 SC4401 TL1807 TL1847 TL1811 R4405 R1832 R4413 R4401 C4402 C1805 R4403 D4401 R4408 TL1817 C1818 R1824 C1826 TL4402 R4415 C1824 R1801 R4402 C1830 R1802 1 R1803 C1820 TL4403 TL4404 SC1803 TL1821 TL1822 TL1824 TL1823 TL1825 SC1801 TL1842 TL4405 R4409 TL1826 TL1801 TL1836 TL1831 TL1827 TL1840 TL1818 TL1838 TL1828 TL1832 TL1833 TL1841 TL1804 R4410 TL1803 TL1802 C4403 1 R4407 D1802 C1831 C1823 C1803 TL4408 L1801 C1806 TL1845 IC1801 C
VE-CG30U VE-CG40U P4401 S4404 J4403 J4402 3 2 J4401 LCD SIDE B JACK SIDE B 2 P7201 SC1701 R1710 P1701 2 R1711 TOP-OPERATION SIDE B OPERATION SIDE B 10 11 12 13 14 15 71 16 17 18 19
VE-CG30U VE-CG40U 11. REPLACEMENT PARTS LIST/ Part No. ★ Description Code EXPLODED VIEWS Ref. No. Ref. No. IC1603 IC1604 IC1901 IC2201 IC2403 ELECTRICAL PARTS LIST Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Les pièces marquéss " å " sont importantes pour maintenir la sècurité de l'appareil.
VE-CG30U VE-CG40U Ref. No. ★ Part No.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No.
VE-CG30U VE-CG40U Ref. No. ★ Part No.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No.
VE-CG30U VE-CG40U Ref. No. ★ Part No. Description Code Ref. No.
VE-CG30U VE-CG40U Ref. No. ★ Part No. Description Code Ref. No. DUNTKB359PM00(VE-CG40U) DUNTKB359PM01(VE-CG30U) JACK PWB UNIT(Continued) RESISTORS R4401 VRS-CZ1JF000JY J 0 1/16W (CG40U) J 0 1/16W J 1k 1/16W (CG40U) J 0 1/16W J 1k 1/16W J 0 1/16W J 0 1/16W J 10k 1/16W J 0 1/16W (CG30U) J 2.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No. Part No.
VE-CG30U VE-CG40U Part No. ★ Description CABINET EXPLODED VIEW Ref. No. Code Ref. No. ★ Part No.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code 12. PACKING OF THE SET Ref. No. Part No. ★ Description QCNWGA016WJZZ (CG40U) QCNWGA017WJZZ (CG30U) AV Cable GCOVAA115WJSA Lens Cap åUADP-A013WJZZ AC Adaptor ★UBATA0002TAZZ Battery QCNWGA018WJPZ USB Cable CDSKA0082TA01 SD Card ★SPAKAA053WJZZ Packing Add. ★SPAKPA050WJZZ Wrapping Paper ★SPAKAA052WJZZ Packing Add.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No. -MEMO- 83 Part No.
VE-CG30U VE-CG40U Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code COPYRIGHT C 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.