Installation Instructions

ManualsBrandsSharp ManualsMicrowave/Micro Hood AccessoriesSharp 30" Drawer Extension Kit For Sharp Microwave Drawer

E 1

30" EXTENSION KIT: SKMD30E3DS

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES TO THE INSTALLER

• Read all of the Installation Manual that is included with the Microwave Drawer before installing the extension kit.

• Observe all governing codes, ordinances, and safety instructions.

• Be sure to leave these instructions with the consumer.

Parts included:

Left Side Trim (qty. 1)

GWAKPB282MRF0

Right Side Trim (qty. 1)

GWAKPB283MRF0

Mounting Brackets (qty. 2)

LBRC-B029MRT0

Bracket Screws (qty. 8)

LX-CZB073MRE0

Trim Screws (qty. 4)

XOTS740PO8000

Install the extension kit after properly installing the microwave drawer in the cabinet. See steps below.

Note that the side trims are marked "L" and "R" on the back side.

TINSKB263MRR0

MICROWAVE DRAWER STANDARD MOUNT, MEASUREMENTS AND INSTALLATION INSTRUCTIONS

A. 21-5/8" (549.3 mm)

B. 4-11/16" (119.1 mm)

C. 1-3/4" (44.5 mm)

D. 21-7/8" (555.6 mm)

E. 23-5/8" (600.1 mm)

F. 16" (406.4 mm)

G. 14-19/32" (370.7 mm)

H. 1-17/32" (38.9 mm) door thickness

I. 15" (381.0 mm) auto drawer opening

J. 4" (101.0 mm)

Figure 1

Summary of content (6 pages)

PAGE 1
30" EXTENSION KIT: SKMD30E3DS INSTALLATION INSTRUCTIONS IMPORTANT NOTES TO THE INSTALLER • Read all of the Installation Manual that is included with the Microwave Drawer before installing the extension kit. • Observe all governing codes, ordinances, and safety instructions. • Be sure to leave these instructions with the consumer. Parts included: Trim Screws (qty. 4) XOTS740PO8000 Bracket Screws (qty. 8) LX-CZB073MRE0 Left Side Trim (qty. 1) GWAKPB282MRF0 Right Side Trim (qty.
PAGE 2
1. Prepare cabinet opening as shown in Figure 2. A B 2. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. C E D M F G O H K I 3. Carefully guide the drawer into the prepared opening. Avoid contact with the sides of the cutout opening and also pinching the cord between the oven and the wall. 4. Slide the drawer all the way back until the side rails are flush with the face of the cabinet. P J L 5. Open the drawer.
PAGE 3
7. Remove the 2 trim screws from each mounting bracket to begin installation. 10. Place side trims on top of the mounting brackets, aligning the screw holes. 8. Open the drawer to properly align brackets to microwave side rails. See Figure 5. 11. Mount the Left and Right 30" trim extensions using the 4 trim screws provided. See Figure 7. Note: The mounting brackets come assembled to the side trims. Note: Each side trim is marked "L" and "R" on the backside to indicate Left and Right.
PAGE 4
MICROWAVE DRAWER FLUSH MOUNT, MEASUREMENTS AND INSTALLATION INSTRUCTIONS B Figures 1 and 2 contain many Microwave Drawer measurements for reference when planning the drawer’s location. A C J This Microwave Drawer can be installed below any electric or gas wall oven. F G * Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach.
PAGE 5
6. Close drawer to complete oven installation. See Figure 6. No oven shown Suggested electrical outlet location A Anti-Tip block B C Figure 4 Front view A. 22-1/8" (562.0 mm) mounting cleat opening width B. 3 0 - 5 / 1 6 " ( 7 7 0 . 0 m m ) m i n i m u m 30-5/8" (777.9 mm) maximum C. 1/8" (3.2 mm) from opening to top of shelf Figure 6 2. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. 7.
PAGE 6
9. Using the 4 holes on each bracket as a template, pre-drill the cabinet using a 1/16" (1.6 mm) bit. Secure the mounting brackets to cabinet with the 8 bracket screws provided. See Figure 8. 10. Place side trims on top of the mounting brackets, aligning the screw holes. Note: Each side trim is marked "L" and "R" on the backside to indicate Left and Right. 11. Mount the Left and Right 30" trim extensions, using the 4 trim screws provided. See Figure 9.